User's Manual

ManualsBrandsm&h Inprocess messtechnik ManualsElectronicsRadio-wave Touch Probe

m&h Inprocess Messtechnik GmbH x Am Langholz 11 x D-88289 Waldburg

Fon +49(0)7529 / 9733-0

x Fax +49 (0)7529 / 9733-7 x vertrieb@mh-inprocess.com

Radio

wave Touch Probe RWP38.41

www.mh

rocess.com

OPERATING INSTRUCTIONS

(Translation of the original operating instructions)

Page

System Components, Technical Data, Dimensions 1

Stylus Change, Battery Replacement 2

Aligning Stylus to Spindle Centre 3

Channels and Frequencies, Setting the Channel 4

Activation Code and Time-out Adjustment 5

Optical Status Display, Adjusting Trigger Force, Maintenance 6

Probe ON/OFF Procedure, Mounting the Shank 7

HSK Shanks, SK Shanks 8

Coromant Capto Shanks,

THERMO-LOCK

Shanks, Other Shanks 9

Measuring Unit Extension 10

Styli, Accessories 11

Safety Advice, Declaration of Conformity, FCC/RSS-Declaration 12

Delivery Contents, Spare Parts, Accessories 13

BA-RWP3841-2311-WEST Subject to change without notice

Summary of content (15 pages)

PAGE 1
Radio-wave Touch Probe RWP38.
PAGE 2
Radio-wave Touch Probe RWP38.41 System Components Radio-wave Receiver RWR95.40 Radio-wave Touch Probe RWP38.41 Technical Data Dimensions Sensing Directions: ± X; ± Y; -Z Max.Stylus Overtravel: XY ±12.5°; Z –6mm (0.24”) Trigger Force with 50mm Stylus: XY = 0.3-1.4N; Z = 2.5-12.5N adjustable Factory Settings: XY = 0.96N; Z = 8.
PAGE 3
Radio-wave Touch Probe RWP38.41 Stylus Change Attention ! After changing the stylus: Adjust stylus to spindle centre! Calibrate probe ! Mounting pin #0885 M=2Nm (1,47 lbf.ft) Battery Replacement Battery cover 38.41-BD (incl. O-Ring 21x2 Viton #4475) 2x Battery 3,6V Type ½ AA #4316 Battery cover open Battery cover closed Attention ! Before opening probe, clean and dry well. Do NOT blow off with compressed air! Open battery cover by a circular motion. Remove empty batteries.
PAGE 4
Radio-wave Touch Probe RWP38.41 Aligning Stylus to Spindle Centre 1 Set „C“ Screws 2 Adjustment to <20µ Hexagon key AF2mm #1097 Hexagon key AF2.
PAGE 5
Radio-wave Touch Probe RWP38.
PAGE 6
Radio-wave Touch Probe RWP38.41 Activation Code and Time-Out Adjustment With 3 available activation codes, „A“ / „B“ / „C“, it is possible to operate up to 3 systems with one receiver. The receiver sends the selected activation code and expect only signals from the selected activation code.
PAGE 7
Radio-wave Touch Probe RWP38.41 Optical Status Display LED blinking green: Probe is transmitting signals LED blinking green / red: Low battery warning LED blinking orange: Stylus deflected Adjusting Trigger Force (patented) In case of strong machine vibrations or heavy styli it is recommended to increase probe trigger force.
PAGE 8
Radio-wave Touch Probe RWP38.41 Probe ON / OFF Procedure The bi-directional probe will be activated and deactivated by the Radio-wave Receiver RWR95.40. After setting the M-Code the probe is activated in <1,5 s and deactivated in <1,5 s after resetting. <1,5s <1,5s >10VDC M-Code 0V ON OFF Mounting the Shank Removing the shank: Remove all „A“ and „C“ screws. Remove shank. Assembling the shank: Carefully slide the shank onto the probe body. Align the „C“ threads with the conical bores.
PAGE 9
Radio-wave Touch Probe RWP38.41 Probe with Shank HSK Available Shanks: L: DIN69893-HSK-E25 93 (3.67”) DIN69893-HSK-A32 110 (4.33”) DIN69893-HSK-E32 110 (4.33”) DIN69893-HSK-A40 110 (4.33”) DIN69893-HSK-E40 110 (4.33”) DIN69893-HSK-F40 110 (4.33”) DIN69893-HSK-A50 110 (4.33”) DIN69893-HSK-A50 142,5 (5.61”) DIN69893-HSK-E50 116 (4.57”) DIN69893-HSK-E50 142,5 (5.61”) DIN69893-HSK-F50 116 (4.57”) DIN69893-HSK-A63 110 (4.33”) DIN69893-HSK-A63 142,5 (5.61”) DIN69893-HSK-A63-70 144 (5.
PAGE 10
Radio-wave Touch Probe RWP38.41 Probe with Shank Coromant Capto Available Shanks: L: Coromant Capto C4 110 (4.33”) Coromant Capto C5 110 (4.33”) Coromant Capto C5 147,5 (5.81”) Coromant Capto C6 116 (4.57”) Coromant Capto C6 147,5 (5.81”) Coromant Capto C8 116 (4.57”) Coromant Capto C8 147,5 (5.81”) Other shanks upon request Order Number: 38.41-C4 38.41-C5 38.41-C5-147,5 38.41-C6 38.41-C6-147,5 38.41-C8 38.
PAGE 11
Radio-wave Touch Probe RWP38.41 Measuring Unit Extension Procedure: Clean and dry the probe body well before removing the probe ! When screwing in the probe, ensure the O-Rings are properly seated ! Align probe to the spindle centre! Calibrate probe out O-Ring 24x2 Viton #2074 Measuring unit C-Spanner #2951 Extension Order Number Length 21.00-VE50 50 (1.96“) 21.00-VE100 100 (3.93“) 21.00-VE200 200 (7.87“) Extension max. 400 (15.75”) in M=12Nm (8,8 lbf.
PAGE 12
Radio-wave Touch Probe RWP38.41 M4-Styli, Shaft-∅ 7 M4-Styli, Shaft-∅ 5 All styli with ceramic shaft All styli with ruby ball Order Number: Order Number: 91.00-T53/6-KE-M4 (Ruby ball) 91.00-T20/2-HM-M4 (Tungsten carbide shaft) 91.00-T20/3-HM-M4 (Tungsten carbide shaft) 91.00-T83/6-KE-M4 (Ruby ball) 91.00-T20/4-HM-M4 (Tungsten carbide shaft) 91.00-T103/6-KE-M4 (Ruby ball) 91.00-T20/5-ST-M4 (Stainless steel shaft) 91.00-T53/6-KE-M4-Si (Silicon nitride ball) 91.
PAGE 13
Radio-wave Touch Probe RWP38.41 Safety Advice ! 1. Manual or automatic positioning of the probe should be protected, so that the machine axis stops feeding if the probe is triggered during its move to the position where actual measuring should begin. 2. Feedhold or spindle-stop resulting from a trigger or ready signal from a probe should only happen if the probe is actually in the spindle.
PAGE 14
Radio-wave Touch Probe RWP38.41 Delivery Contents, Spare Parts, Accessories Delivery Contents Order Number 38.41-RWP Description Radio-wave Touch Probe RWP38.41 4xBattery Type 1/2AA(3,6V) Toolbox Storage box Spare Parts and Tools Order Number Description #4316 Battery Type ½ AA (3,6V) 38.41-BD Battery cover #4475 O-Ring 21x12 Viton for Battery cover #1351 Clamping screw AF2.
PAGE 15
Radio-wave Touch Probe RWP38.41 Delivery Contents, Spare Parts, Accessories Accessories Order Number Description 21.00-VE50 Extension L=50mm (1.96“) 21.00-VE100 Extension L=100mm (3.93“) 21.00-VE200 Extension L=200mm (7.87“) 25.