Use and Care Manual

What’s in the Box
Lay out all box components
included on a level and
comfortable workspace:
MM00175 INSTRUCTION MANUAL
ASSEMBLY • INSTALLATION • OPERATION • MAINTENANCE • SAFETY
(2) A Curved Metal Tube & Foam
(2) B Straight Metal Tube & Foam
(2) C Rope Set with Eye Bolts
(1) D Teepee Tent Cover
(1) E Mat/Seat
(1) F Carabiner
(4) G Acorn Nut Cap
(8) H Lock Washer
(8) I Regular Washer
(1) J Wrench
Teepee Tent Swing
ASSEMBLY INSTRUCTIONS
BEFORE YOU START: Observing the following statements
and warnings reduces the likelihood of serious or fatal injury.
ASSEMBLY WARNING:
• Due to the presence of small parts during assembly, keep
out of reach of children unl assembly is complete.
• To prevent serious injury, children must not use the swing
unl properly installed. Do not use swing if any damage or
deterioraon is detected or parts are missing. Contact point
of purchase retailer or M&M Sales Enterprises, Inc.
• Never substute parts.
• Please keep instrucons for future reference.
ASSEMBLY INSTRUCTIONS:
• Assembly should be completed by adult person(s).
We intend for our products to bring joy not frustraon.
• A at level surface approximately 5 . x 5 . will be
needed to spread out materials for assembly.
• One hex wrench is included for ghtening the eye bolts.
• Lay out all necessary swing components pictured.
• Unfold material swing cover on level surface with design facing up.
STEP 1
STEP 2
STEP 4
STEP 6
STEP 7
STEP 8
LBS.
250
Insert one curved metal tube with foam through
the swing cover sleeve. Before inserng the
remaining tubes, note the direcon of the rst
tube. All narrow ends of tube will t into wider
opening end of an adjoining tube. Insert the
remaining three tubes.
Insert all narrow ends
of tube into wider
end of adjoining tube,
making sure to align the
overlapping holes.
Add washer and nut to the boom side of tube bolt
and secure. Tighten with wrench. Repeat steps 3,
4 and 5 on remaining three straps with remaining
three screw ends. Pull the hook/loop straps back
over the tubing frame and aach to the hook/loop
fastener on underside of swing.
Finished Teepee Tent
Swing should look as
pictured above. Ropes
should not cross each
other above swing.
Hang and enjoy.
STEP 3
Pull the eye bolt ends of each rope
through the canvas slots. Slide one
regular washer and one lock washer
onto the eye bolt. Then, insert the
eye bolt through the holes formed
at the tube’s connecon points.
Clip the carabiner through both
o-rings at the end of each rope
set and ghten. Lastly, place the
buckle on the Teepee Tent cover
through the carabiner. Buckle to
secure and ghten.
Figure 1
18”(min)-24”(max) ground clearance.
INSTALLATION
TREE LIMB OR CROSS BAR ASSEMBLY:
First test the tree limb or cross bar to ensure that it is
secure, it will support at least 250 lbs., is over level ground,
has a minimum height of 7 feet and is no less than 6 feet
on all sides from vercal elements. Swing should have a
clearance of at least 1.5 mes the total length of all the
rope measured from the tree limb/horizontal beam to the
tree strap aachment point. (See: Figure 1)
GENERAL INSTRUCTIONS:
• DO NOT install home playground equipment
over concrete, asphalt, packed earth, grass,
carpet or any other hard surface — A fall onto a
hard surface can result in serious injury or death
to the equipment user.
• To prevent serious injury, equipment must not
be used unl properly installed.
ADJUST SWING HEIGHT
• Adjust swing hanging length so plaorm is
parallel with ground. Boom of swing should
be no more than 24 inches and no less than 18
inches from the ground.
• Never add extra length to chain or rope.
The chains or ropes provided are the maximum
length designed for the swinging element(s).
NOTE: Connued on Back Side
At least 6’
from the
trunk or 1.5x
the length the
swing rope.
A
B
C
D
Tree Strap
E
F
G*
H* I*
J
STEP 5
M&M Sales
Enterprises, Inc.
1300 Synergy Ct, Dubuque, IA 52002
877-242-0514
www.mandmsalesinc.com
*Washers and Acorn Nut Cap
Pictured as Actual Size
Swing with or
without Teepee
Tent Cover