USER MANUAL FOR LV-700 Lecip Arcontia confidential (V1.
1. Technical Overview of LV-700 • Software Platform o Linux Kernel 4.1.38 o QT 5.7.1 Application Frame work o Python 3.5.2 • NXP Application processor o ARM Cortex-9 single core 32-bit o 1 GHz o Automotive grade • System o o o 1024 MB DDR3L SDRAM 2x 36Mx16 x 8 banks 4GB e-MMC flash • External Interfaces o Ethernet 100Base-T2 with embedded EUI-48 MAC Address o 2 x RS 232 o RS-485 o 2 x Isolated Bipolar Outputs (max. 200mA) o Unique ID of the Unit Holder • User Interface o o o • • • • 5.
• Service Area (Service Hatch) o USB OTG o 2-bit Boot configuration switch o SIM card Slot o 4 x SAM Interfaces o RS-232 for Linux console o Tamper Switch o Manual Rest button o Visually and by MCU readable 10-bit H/W Revision/Variant/BOM resistive network • Supported Smart Cards o Mifare Classic, Mifare Plus, Mifare Ultralight, Mifare Ultrlight C, Mifare Desfire, Mifare SmartMX, GTML, GTML2, ISO 144434A tags, ISO 14443B tags, Felica, Calypso • Supported SAM o Mifare SAM AV1/AV2 and other ISO/IEC 7816
2. External/Electrical Interface and Access Card Here is the detailed description of Pinout, connectors and function or available signals on Access card. 1 2 3 4 5 6 7 8 9 10 11 2 J2 J3 J4 Pin nr. Interface 1 2 3 4 5 6 7 1 2 1 2 12 13 14 3 4 5 15 16 17 18 19 20 6 7 1 2 3 4 21 22 23 24 25 26 27 28 29 30 1 Conn. L2R Pos. Fig 1. Access Card J5 J6 5 6 7 1 2 3 4 5 6 7 RS232-1 IGN POWER SUPPLY ETHERNET RS232-2 RS485 GPO1 GPO2 GPI1 GPI2 Function Wire Wire-end ferrule (mm2) AWG RTS 0.
Highly recommended crimp tool is KNIPEX 975314 or any other with a hexagonal crimp shape. Figure 2: Flat shape Figure 3: Hexagonal shape Using crimp tool with a non-hexagonal shape (Figure 2) will produce a flat form of wire-end ferrule that cannot be pushed in the hole of spring-cage terminal block. Hexagonal form (Figure 3) however is a good approximation of the circle and pushing in should be easily done. Lecip Arcontia confidential (V1.
3. Board to Board Connector The passive part (Access Card) of the Arcontia validator is connected to the active part (Main Board) through a pair of B2B connectors. Access card is equipped with receptacle side (J1) while main board with mating header side (J1). The connector pair is Hirose FX23 and FX23L series. It is a pair of 40+4 hybrid power/signal contacts with floating ability. Figure 4: FX23/FX23L XY-Floating Ability Floating movable amount in both X and Y-direction is ± 0.
The applied pair of the receptacle and the header gives a stacked height of 19mm. Figure 6: The Applied Combination Lecip Arcontia confidential (V1.
4. User Interface An overview of user Interface is shown in the picture below. The user interface is consist of: • • • • • 5.7" LCD 24 LVDS VGA (680x480 Resolution) 4 x Indication LEDs Smart Card Reader QR code Reader Speaker Speaker 5.7” LCD (680x480) Smart Card Reader Area Indication LEDs QR Code Reader Figure 7: User Interface Lecip Arcontia confidential (V1.
5.Mechanical Interface 245mm 140 (mm) 47mm Figure 8: Dimension Front View (mm) Figure 9: Dimension Side View (mm) Lecip Arcontia confidential (V1.
5. Electrical Interface Overview 5.1 Top Placement of LV-700 Main Board SD1 J1 J6 J10 SIM Figure 10: Top Placement of LV-700 Main Board • • • • • • • • • • SAM1 – Secure Access Module Slot no 1 SAM2 – Secure Access Module Slot no 2 SAM3 – Secure Access Module Slot no 3 SAM4 – Secure Access Module Slot no 4 SIM1 – SIM Module Slot SD1 – Micro SD slot for additional memory J1 (Hirose: FX23-40P-0.
5.1.1 Service Hatch • SAM1 – SAM 4 – Secure Access Module A Secure Access Module (or Secure Application Module) is based on smartcard ICs and is used to enhance the security and cryptography performance in devices, commonly in devices needing to perform secure transactios, such as paying terminals. It can be used for computation and secure authentication against smart cards or contactless EMV cards.
5.2 Bottom Placement of LV-700 Main Board Figure 11: Bottom Placement of LV-700 Main Board J3 J5 • • J5 (Molex: 502244-3330) – 5.7” LCD Interface J3 (TE-Connectivity: 1759503-1) – Antenna’s Slot Lecip Arcontia confidential (V1.
6. Mechanical Interface 215mm 62.23mm 80.4mm 35.70mm 9.90mm Lecip Arcontia confidential (V1.00 2019-05-13) 121.46mm 25mm 40.
7. Instruction for Validator Demonstration Software A LV-700 device normally has an LV-700 demonstration software preinstalled, or it comes with a SDcard containing the operating system and this software. When the device is powered on it will automatically launch this demo. This automatic boot-up of the demonstration software may or may not be present.
7.1 Main Menu The first screen you are presented with is the Main Menu. It has four immediate options to choose from. Two of them, “Adult Single” and “Student Single”, are related to the contactless card reader and the remaining two, “Day Pass Barcode” and “Single Barcode”, to the onboard bar code camera. These options illustrate the process of paying for a ticket using a card or a barcode. Main Menu. Lecip Arcontia confidential (V1.
There is another fifth option not immediately visible; swiping left on the display in the Main Menu will bring you to the Main Service Menu. Main Service Menu. In the main service menu you can format cards to be used in the payment demos on the main menu, or top up already formatted cards. It also gives access to changing screen brightness, volume and currency. Lecip Arcontia confidential (V1.
7.1.1 Back Button Some screens have a back button. Tapping this will return the user to the previous screen. Lecip Arcontia confidential (V1.
7.2 Adult Single Red area doesn’t appear in the application. Tapping the “Adult Single” option in the Main Menu will request the user to tap a card to pay for a ticket. Once a card has been tapped it will be deducted with the specified amount. The card used must first have been formatted as is done in the “Create Card” section. Lecip Arcontia confidential (V1.
Application requesting user to tap card. Lecip Arcontia confidential (V1.
If the validator was able to deduct the specified amount it will play a sound and show the success screen. It will display the amount deducted and current balance. Success screen for Adult Single ticket. In case of insufficient funds or a communication error, or some other error it will display an error screen. Lecip Arcontia confidential (V1.
7.3 Student Single Clicking the “Student Single” option in the Main Menu will request the user to tap a card. Once a card has been tapped it will be deducted with the specified amount. The card used must first have been formatted as is done in the “Create Card” section. Lecip Arcontia confidential (V1.
Application requesting user to tap a card. Lecip Arcontia confidential (V1.
If the validator was able to deduct the specified amount it will play a sound and show the success screen. It will display the amount deducted and current balance. Success screen for Student Single ticket. In case of insufficient funds or a communication error, or some other error it will display an error screen. Lecip Arcontia confidential (V1.
7.4 Day Pass Barcode Tapping the “Day Pass Barcode” option in the Main Menu will request the user to present a barcode to the camera. Depending on the configuration of the camera, it will start flashing immediately scanning for barcodes. Also, the types of barcodes supported by the camera is determined by the configuration. A barcode can contain custom data, hence the illustrations regarding output may differ depending on the barcode presented to the camera. Lecip Arcontia confidential (V1.
Application requesting user to present a barcode. If the validator detects a barcode it will play a sound and display the data on a success screen. In the picture below the contents of the barcode was “Expire+MM.DD.YYYY”. Lecip Arcontia confidential (V1.
Day Pass Barcode success screen. Lecip Arcontia confidential (V1.
7.5 Single Barcode Tapping the “Single Barcode” option in the Main Menu will request the user to present a barcode to the camera. Depending on the configuration of the camera, it will start flashing immediately scanning for barcodes. The types of barcodes supported by the camera is determined by its configuration. Since a barcode is custom data the illustrations regarding output may differ depending on the barcode presented to the camera. Lecip Arcontia confidential (V1.
Application requesting user to present a barcode. Lecip Arcontia confidential (V1.
If the validator detects a barcode it will play a sound and show the data on a success screen. In the picture below the contents of the barcode was “MM.DD.YYYY HH:MM+€4.00”. Single Barcode success screen. Lecip Arcontia confidential (V1.
7.6 Create Card Tapping the “Create Card” option in the Main Service Menu will request the user to present a card. Once in the field the reader will format (and set a balance) the card so that it can be used with the other card related options. The card must be a Mifare DESFire card, otherwise it will not work and an error screen will be displayed. In other words; all other card related operations depend on a Mifare DESFire card that has been properly formatted. Lecip Arcontia confidential (V1.
Requesting user to tap a card for formatting. Lecip Arcontia confidential (V1.
If the validator could successfully format the card it will play a sound and display a success screen. Create Card success screen. Lecip Arcontia confidential (V1.
7.7 Top up Card Tapping the “Top up” option in the Main Service Menu will request the user to present a card. Once in the field the reader will top up (increase it’s balance) the card so that it can be used with the other card related options. The card must first have been created and formatted properly as is done in the “Create Card” option. Lecip Arcontia confidential (V1.
First screen of Top up. Once a valid card has been tapped it will proceed to the next section. Otherwise it will display an error and return to the Main Service Section. Lecip Arcontia confidential (V1.
Second screen of Top up. Requesting user to specify amount. Next step is to specify the amount to top-up. This is done by tapping on the desired amount. Once an amount has been selected the user will be requested to tap the card once again. Lecip Arcontia confidential (V1.
Third screen of Top up. Requesting user to tap a card to be topped up with the amount specified in the previous section. Lecip Arcontia confidential (V1.
If the card was valid and the operation was successful a sound will be heard and the success screen displayed. It will display the current balance of the card. Top up success screen. Lecip Arcontia confidential (V1.
7.8 Setting Tapping the “Setting” option in the Main Service Menu will open up the Setting menu. Here it’s possible to change the brightness of the screen, adjust volume and also change the currency displayed. Lecip Arcontia confidential (V1.
Setting menu. Lecip Arcontia confidential (V1.
7.8.1 Volume Tapping the “Volume” option in the Main Service Menu will allow the user to change the volume of the sounds played by the validator. Lecip Arcontia confidential (V1.
Volume screen. Pressing the “+” button will increase the volume. Pressing the “-“ button will decrease the volume. A sound is played every time the volume is changed so that one can easily find the desired volume. Lecip Arcontia confidential (V1.
7.8.2 Brightness Tapping the “Brightness” option in the Main Service Menu will allow the user to change the brightness of the display of the device. Lecip Arcontia confidential (V1.
Brightness screen. Pressing the “+” button will increase the brightness of the display. Pressing the “-“ button will decrease the brightness of the display. Lecip Arcontia confidential (V1.
7.8.3 Currency Tapping the “Currency” option in the Main Service Menu will allow the user to change the currency displayed by the application. Such as the amount deducted when processing an “Adult Single” ticket. Lecip Arcontia confidential (V1.
Currency screen. To change the currency one must tap on one of the two options. Lecip Arcontia confidential (V1.
7.9 Service Service is not implemented. Nothing will happen if tapped. Lecip Arcontia confidential (V1.
7.10 Error Screen Error Screen. In case of errors during card transactions an error is displayed. This could be due to interrupted or corrupted communication, balance too low etc. An error sound is also played when this is displayed. Lecip Arcontia confidential (V1.
8. Installation 8.1 Required Tools and equipment 8.2 Mounting Module Assembly 8.3 Kit in Bag details 8.4 On –board Mount Procedure 8.2 Mounting Module Assembly Lecip Arcontia confidential (V1.
• Mounting Module Insert the lock Shaft Lecip Arcontia confidential (V1.
• Mounting Module: Assemble the lock system Lecip Arcontia confidential (V1.
• Mounting Module: Secure the lock Shaft Lecip Arcontia confidential (V1.
8.3 Kit in Bag details • Pole Mounting Kit Lecip Arcontia confidential (V1.
• Wall Mounting Kit Lecip Arcontia confidential (V1.
8.4 On-Board Mount Procedure Lecip Arcontia confidential (V1.
• On-Board Mount: Insert Pole Positioners Lecip Arcontia confidential (V1.
• On-Board Mount: Disassemble Connection Parts Lecip Arcontia confidential (V1.
• On-Board Mount: Cable Entry Lecip Arcontia confidential (V1.
• On-Board Mount: Pole Fittings Lecip Arcontia confidential (V1.
• On-Board Mount: Pole Brackets Lecip Arcontia confidential (V1.
• On-Board Mount: Back Pole Cover Lecip Arcontia confidential (V1.
• On-Board Mount: Connecting Cables Lecip Arcontia confidential (V1.
• On-Board Mount: Connection Hatch Lecip Arcontia confidential (V1.
• On-Board Mount: Operating Unit Lecip Arcontia confidential (V1.
FCC Part 15 Information to User: Part 15.19(a): This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Part 15.105: Class A Statement: NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.