Simply Connected Quick Install Guide XAP-1210 High Power Wireless 300N Low Profile Access Point Use the XAP-1210 to: • Deliver Broader WI-Fl Coverage and Eliminate Client Device Roaming Issues with Fewer APs • Improve Data Rates with Multi-Stream Wireless 802.
XAP-1210 Quick lnsta/ I Guide Quick Install Guide Model Number: XAP-1210 High Power Wireless 300N Low Profile Access Point FCC ID: W59XAP1210 IC: 8584A-XAP1210 © 2014 Luxul. All Rights Reserved. No part of this publication may be modified or adapted in any way, for any purposes without permission in writing from Luxul. The material in this manual is subject to change without notice. Luxul reserves the right to make changes to any product to improve reliability, function, or design.
LUlif'UL Simply Connected PACKAGE CONTENTS The following Items should be Included In the box: ... One: XAP-1210 Wireless AP ... One: Mounting Bracket and Hardware ... One: PoE Injector and Power Cord ... Two: Ethernet Cables ... One: Quick Install Guide NOTE: If any of the listed items are missing or damaged, please contact the reseller from whom you purchased for ret'um/replacement.
XAP-1210 ___. ___ Quick lnsta/ I Guide PoE Injector LED Indicators Name PWR ..._ Status Function On Power is connected to the injector Off Injector is not receiving power PREPARING FOR INSTALLATION System and Power Requirements ~ Computer with supported Web browser. Minimum supported web browser ver- sions include: I.E. 9.0, Firefox 2.5, Safari 5.0, Chrome 3.0 and up. The Web browser is used to configure the XAP-1210. ~ The POE injector power supply requires AClOOV - 240V, 50Hz - 60Hz.
LU~UL Simply Connected XAP-1210 mounted on a ceiling XAP-1210 mounted on a wall Desktop Installation Place on any flat surface XAP-1210 on a desktop or flat surface Connecting the Ethernet Cable With the XAP-1210 properly mounted, you can now plug the Ethernet Cable into the RJ-45 connector. NOTE: Category-5, super Category-5 or Category-6 unshielded twisted pair {CAT5/CAT5e/CAT6 UTP) cables can be used.
MOUNTING PATTERN @~I_ _ @.
J @ J @
XAP-1210 Quick lnsta/ I Guide PoE Injector Setup ~ Data In: Connect an Ethernet cable from your router or switch to the Data In port of the included PoE Injector ~ Data & PWR Out: Connect an Ethernet cable from the Data & PWR Out port of the included PoE Injector to the PoE Port of the XAP-1210 ~ AC Power: Connect the included AC Cord to the Power Input of the Included Injector first and then to the AC outlet.
LUlfUL Simply Connected CONFIGURATION Default IP Address The XAP-1210 is not equipped with an internal DHCP server. If connected to a Luxul Router, configuration will be automatic. Otherwise, the IP address of the computer for login and configuration will need to be manually configured. The table below lists the default parameters of the XAP-1210. Parameter: Default Value Default IP address: 192.168.0.10 Default user name: admin Default password: admin The Luxul XAP-1210 default IP addresss is 192.168.0.
XAP-1210 Quick lnsta/ I Guide ADVANCED SETTINGS For advanced settings information go to luxul.com WARNINGS AND SAFETY INFORMATION ~ Verify that the electrical circuits have appropriate grounding and overload protection. ~ Attach only approved power cords to the device. ~ Verify there is adequate ventilation around the device, and that ambient temperatures meet equipment operation specifications. ~ The XAP-1210 is designed for indoor use only. DO NOT place this outdoors.
LUl lUL Simply Connected Warning: Exposure to Radio Frequency (RF) Radiation: The radiated output of this device is below the FCC radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact during normal operation is minimized. ~ The end user must avoid any extended human RF exposure directly in front of the device, up to a distance of 20cm, when unit is on.
Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. NOTE: O)The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment.