Luxshare Precision Industry (Kunshan) Co., Ltd Wireless Charger For Mobile Phone In The Car 15W WACM Tx Controller Specification （JMC-Ford Motor） Statement: All rights reserved by Luxshare Precision Industry (Kunshan) Co.,Ltd (hereinafter referred to as LUXHSAREICT)! Without the LUXHSAREICT duly authorized in writing, whether to any third party organizations, groups or individuals,whether unintentional or intentional, it’s illegal! Security classification of the document belongs to: business secret.
Functional Specification WPC002 Content 1 Overview ...............................................................................................................3 1.1 Overview ................................................................................................... 3 1.2 Purpose/Scope ........................................................................................... 3 1.3 Revision Chart .......................................................................................... 3 1.
Functional Specification 1 WPC002 Overview 1.1 Overview This document belongs to LUXHSAREICT; This document was initially applied to the Tx controller of JMC Ford Car Mobile Wireless Charging Module; The product is currently used in the JMC Ford CX743 and subsequent derivative vehicles If there is any misunderstanding between English and Chinese in this document, please refer to the meaning in Chinese. 1.
Functional Specification 1.5 AMS Automobile Multimedia System FOD Foreign Object Detection CAN BUS Controller Area Network-BUS DTC Diagnostic Trouble Code EMC Electro Magnetic Compatibility KL.15 Ignition Supply KL.30 Battery Positive KL.31 Battery Negative FSC Functional Status Classification DUT Device Under Testing TBD To Be Defined NC NO Change WPC002 System Definition Abbreviation Chart 1‐3 Item Description Coil Tx MP-A9 Three Coils Full Load Max.
Functional Specification WPC002 《ISO 10605:2008》 AUTO 15W WPC Tx 2019-08-02 Copyright © 2016~2019 Luxshare Precision Industry (Kunshan) Co.,Ltd Page 5 of 15 All Rights Reserved.
Functional Specification 2 WPC002 Introduction 2.1 System Introduction This specification describes an automotive Wireless Charging Module(Hereinafter referred to as WACM); WCAM usesan an Electromagnetic induction technique; It is applied to vehicles and provides wireless power transmission to the mobile phone that meets the conditions, which can ensure that the power received by the receivers is 15W Max.
Functional Specification WPC002 Chart2‐1 2.2.2 Product 2D AUTO 15W WPC Tx 2019-08-02 Copyright © 2016~2019 Luxshare Precision Industry (Kunshan) Co.,Ltd Page 7 of 15 All Rights Reserved.
Functional Specification WPC002 Chart2‐2 Product 2D 2.2.3 Chart2‐3 2.3 Technique Parameters 2.3.1 Product Technique Parameters Parameters Electrical Specification Output Spec. Max. Output Power WACM Operating Temperature Range Temperature Range Range 15W Max -40℃~65℃ （＞65℃，Over-temperature Storeage Temperature Range AUTO 15W WPC Tx 2019-08-02 Copyright © 2016~2019 Luxshare Precision Industry (Kunshan) Co.,Ltd Protection） -40℃~85℃ Page 8 of 15 All Rights Reserved.
WPC002 Functional Specification Wireless Charger Function Nominal：9~16V （Hysteresis interval exists， 8~9V，16~18V also works） Communication 6~18V Function Module Rated Operating Range 12.4V Voltage Operating Voltage Curre Max. Output Current nt 3A Efficiency at Max. efficient Efficie point when input voltage is Current Consumption ＞70% 12.4v. ncy Operatiing Current in –load ≤100mA mode 暗电流 Dark Current ACC or IGN OFF Operating Wireless Charger switching frequency ≤0.
Functional Specification 2.4 WPC002 System Block Diagram 2‐6 Chart System Schematic 2.5 Ports Definition 2.5.
Functional Specification 2.5.2 Main Body Connector WPC002 Definition Connector Shape Figure Male prot type : luxshare Female prot type： TE ：1743282-1，TE:5-963715-1 PIN Definition IO Characteristics NO. Pin NO. 1 A1 KL.30 B+ Power Input Power 5A Max 2 A2 Green LED Driver output L-SMOS 20mA Max 3 A3 PEPS Disable DL-I 10mA Max 4 A4 KL.31 GND Power Ground Power 5A Max 5 A5 CAN_H COMM 500mA 6 A6 CAN_L COMM 500mA 7 A7 Red LED Driver output L-SMOS 20mA 8 A8 IGN （KL.
WPC002 Functional Specification 2.5.3 Wire Harness Connector Definition Connector Shape Figure PIN Definition IO Characteristics NO. Pin NO. 1 B1 KL.30 B+ Power Input Power 5A Max 2 B2 IGN （KL.15）Power mode input DH-I，-WeekUp 20mA 3 B3 / / / 4 B4 KL.
Functional Specification WPC002 Connector Shape Figure Female prot type：TE ：1743282-1， TE:5-963715-1 Match Port： Wireless Charger main body connector PIN Definition IO Characteristics NO. Pin NO. 1 A1 KL.30 B+ Power Input Power 5A Max 2 A2 Green LED Driver output L-SMOS 20mA Max 3 A3 PEPS Disable DL-I 10mA Max 4 A4 KL.31 GND Power Ground Power 5A Max 5 A5 CAN_H COMM 500mA 6 A6 CAN_L COMM 500mA 7 A7 Red LED Driver output L-SMOS 20mA 8 A8 IGN （KL.
Functional Specification 2.6 WPC002 Coil Definition 2.6.1 Coil Dimension MP-A9 Chart 2-11 Primary Coils of Power Transmitter design MP-A9 Chart 2-12 Primary Coil of Power Transmitter design MP-A9 2.6.2 Bottom Coil Dimensions Specification NO. Parameter Symbol Value 1 Outer length dol 53.0±1.5 mm 2 Inner length dil 27.5±0.5 mm 3 Outer width dow 46.7±1.5 mm 4 Inner width diw 20.5±0.5 mm 5 Thickness dc 1.6±0.
WPC002 Functional Specification 2.6.3 NO. Top Coil Dimensions Specification Parameter Symbol Value 1 Outer length dol 53.0±1.5 mm 2 Inner length dil 25.2±0.5 mm 3 Outer width dow 48.1±1.5 mm 4 Inner width diw 19.5±0.5 mm 5 Thickness dc 1.6±0.5 mm 6 Number of turns per layer N 12 7 Number of layers – 1 Remark Blank Below Chart 2-14 Top Primary Coil parameters of Power Transmitter design MP-A9 2.6.4 NO. Coil Specification Item Specifications Typ.
Functional Specification WPC002 FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
