Installation Manual

ManualsBrandsLutron Electronics ManualsElectronicsHome Works tabletop radio frequency keypad control

Please Read Before Installing

RF Tabletop Keypads

HRT-

5KP-A, -C 10KP-A, -C 15KP-A, -C 6LKP-A, -C

5RL-A, -C 10RL-A, -C 15RL-A, -C 6LRL-A, -C

120/127 V ~ , 50/60 Hz (9 V adapter, -A and -C models)

Batteries: 2 AAA size, 1.5V each (-C models)

Installation Instructions

Overview

RF Tabletop Keypads are for use with HomeWorks sys-

tems. The keypad buttons are programmed with a per-

sonal computer using the HomeWorks Utility.

Up to 32 keypads, each with a unique address, can be

assigned to each HomeWorks RF Processor.

Important Notes

Codes: Install in accordance with all local and national

electrical codes.

Power: Battery-powered models (-C only): Use only high

quality alkaline batteries, two (2) size AAA, 1.5V each.

Caution - Do not use rechargeable batteries.

Using improperly rated batteries could damage

the RF Tabletop Keypad.

All models (-A, -C): Use only the adapter provided by

Lutron with your RF Tabletop Keypad.

Caution - Using an adapter not rated for the

following specifications could damage the key-

pad and possibly overheat the adapter.

• Input: 120/127 VAC, 50/60 Hz

• Output: 9 VDC/300 mA Class 2

Environment: Ambient operating temperature:

32-104°F (0-40°C), 0-90% humidity, non-condensing.

Indoor use only.

Faceplates: Do not paint controls or faceplates.

Cleaning: To clean, wipe with a clean damp cloth. DO

NOT use any chemical cleaning solutions.

RF Device Placement: RF Tabletop Keypads must be

located within 30 feet (10m) of an RF Signal Repeater or

an RF Processor.

Setup: RF Tabletop Keypads will not function until they

are addressed and programmed. See the HomeWorks

Utility online help.

HRT-5KP

HRT-5RL

HRT-10KP

HRT-10RL

HRT-15KP

HRT-15RL

HRT-6LKP

HRT-6LRL

Summary of content (4 pages)

PAGE 1
RF Tabletop Keypads Installation Instructions HRT5KP-A, -C 10KP-A, -C 15KP-A, -C 6LKP-A, -C 5RL-A, -C 10RL-A, -C 15RL-A, -C 6LRL-A, -C Please Read Before Installing 120/127 V ~ , 50/60 Hz (9 V adapter, -A and -C models) Batteries: 2 AAA size, 1.5V each (-C models) Overview HRT-5KP HRT-5RL HRT-10KP HRT-10RL HRT-15KP HRT-15RL HRT-6LKP HRT-6LRL RF Tabletop Keypads are for use with HomeWorks systems. The keypad buttons are programmed with a personal computer using the HomeWorks Utility.
PAGE 2
Installation Battery Installation (-C Models) Adapter Installation (All Models) 1. Remove battery cover. 1. Find a suitable location for the RF Tabletop Keypad. Place the keypad in a convenient and accessible location. Note: RF Keypads must be located within 30 feet (10m) of an RF Signal Repeater or an RF Processor. 2. Apply power to the RF Tabletop Keypad. Plug in power cord and adapter 2. Install batteries as shown. Use two 1.5V AAA alkaline batteries only.
PAGE 3
Troubleshooting Guide RF Keypads will not control other system devices until the keypads are addressed and programmed. See the HomeWorks® Utility online help. Symptom Cause and Action LEDs on an adapter-powered keypad do not light. No power available to keypad. • Verify adapter is plugged in. Faulty adapter. • Replace adapter. A battery-powered keypad will not “wake up” when a button is pressed. Dead, low, or no batteries in keypad. • Replace the batteries. Batteries are incorrectly installed.
PAGE 4
FCC Information Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed in accordance with the instructions, may cause harmful interference to radio communications.