User's Manual

ManualsBrandsLutron Electronics ManualsElectronicsControl Unit

Attention Contractors...

Installer’s Guide Addendum for

Tabletop Transmitters

A Step-by-Step Guide for Installing, and Operating

Tabletop Transmitters for use with a Lutron RadioTouch

Visual Environment Control System

1234 5678 9101112 13141516

CLASS 2 LOW VOLTAGE WIRING

12345

Power

Status Program

Burn-In

123

Sivoia Cntrl 1

Sivoia Cntrl 2

RTA-RX-F-SC

Radio Frequency Controller

LISTED 243C

Ind. Cont. Eq.

Coopersburg, PA 18036

STATUS INDICATOR OPERATION

ON - Burn-in Mode

Slow Blink -Normal Operation Mode

Fast Blink - Program Mode

Very Fast Blink - Receiving RF Data

RadioTouch

345678910

12 13 14

15 16

Occ. Com

Signal

15V

24V

Circuit Com

Sw Closure 1

Sw Closure 2

Sw Closure 3

Sw Closure 4

Sw Closure 5

Closure Com

0-10 Purple

0-10 Gray

Receiver

Settings

Terminal connections

are Class 2.

Occ. Sensor

0-10 V

Shade Switch Closures

12345

Powered

When Lit

Status

Indicator

Program

Button

Burn-in

Button

RECEIVER SWITCH SETTINGS

1. UP-Preset Lock DN.-Preset Adj.

2. UP-Occ. Sensor DN.-Emerg. Set.

3. UP-FDB Mode DN.-ECO Mode

4. UP-OFF DN.-Min. Light

5. UP-Auto ON DN.-Manual ON

See Installers Guide for System

Addressing and Programming Instructions

123

Shade

Settings

SHADE SWITCH SETTINGS

1. UP-A/C Shades DN.-Normal Oper.

PS Signal

Summary of content (8 pages)

PAGE 1
Attention Contractors... RadioTouch RTA-RX-F-SC TM Radio Frequency Controller LISTED 243C Ind. Cont. Eq. ® Coopersburg, PA 18036 STATUS INDICATOR OPERATION ON - Burn-in Mode Slow Blink -Normal Operation Mode Fast Blink - Program Mode Very Fast Blink - Receiving RF Data RECEIVER SWITCH SETTINGS 1. UP-Preset Lock DN.-Preset Adj. 2. UP-Occ. Sensor DN.-Emerg. Set. 3. UP-FDB Mode DN.-ECO Mode 4. UP-OFF DN.-Min. Light 5. UP-Auto ON DN.-Manual ON SHADE SWITCH SETTINGS 1. UP-A/C Shades DN.-Normal Oper.
PAGE 2
Hardware Installation RadioTouch Addressing a Tabletop Transmitter Each column of buttons on the tabletop transmitter must be addressed to the Controller that you wish to control with that column. Addressing Columns of Buttons Step A - Press and release the programming button on the Controller. After the button is pressed the lights will cycle up and down for 3 seconds to notify you that you are in programming mode, and settle at 50% light output.
PAGE 3
Hardware Installation RadioTouch Deleting a Tabletop Transmitter Each column of buttons on the tabletop transmitter must be deleted separately from the Controller that you no longer wish to control. Deleting Columns of Lights Step A - Press and release the programming button on the Controller. After the button is pressed the lights will cycle up and down for 3 seconds to notify you that you are in programming mode, and settle at 50% light output.
PAGE 4
Hardware Installation RadioTouch Setting the ON light level of a two button, dimmable lighting column Remote Method Note: No DIP switches need to be switched to perform this operation. Step A - Press and hold the ON and the lower buttons for 5 seconds. The lights will flash to notify you that you are in Preset Adjust Mode, and settle at 100% light level.
PAGE 5
Hardware Installation RadioTouch RadioTouch RTA-RX-F-SC TM Radio Frequency Controller LISTED 243C Ind. Cont. Eq. ® STATUS INDICATOR OPERATION ON - Burn-in Mode Slow Blink -Normal Operation Mode Fast Blink - Program Mode Very Fast Blink - Receiving RF Data RECEIVER SWITCH SETTINGS 1. UP-Preset Lock DN.-Preset Adj. 2. UP-Occ. Sensor DN.-Emerg. Set. 3. UP-FDB Mode DN.-ECO Mode 4. UP-OFF DN.-Min. Light 5. UP-Auto ON DN.-Manual ON SHADE SWITCH SETTINGS 1. UP-A/C Shades DN.-Normal Oper.
PAGE 6
Hardware Installation RadioTouch Setup for AC Motorized Window Treatments (RTA-RX-F-SC only) Make sure that the RadioTouch Controller is properly wired. Refer to the RadioTouch Installer’s Guide (P/N 030-200) for detailed wiring information. Step A - On the RadioTouch Controller, flip SHADE SETTINGS DIP SWITCH #1 UP for open, close, and stop functionality. Step B - Make sure appropriate transmitters are added to the Controller. See page 2 for Addressing Tabletop Transmitters to Controllers.
PAGE 7
Notes RadioTouch Tabletop Transmitter Addendum 7
PAGE 8
LIMITED WARRANTY Lutron will, at its option, repair or replace any unit that is defective in materials or manufacture within one year after purchase. For warranty service, return unit to place of purchase or mail to Lutron at 7200 Suter Rd., Coopersburg, PA 18036-1299, postage pre-paid. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES, AND THE IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TO ONE YEAR FROM PURCHASE.