Users Manual

Warnings
Disposal:
The product with this mark indicates that this product shouldn't be disposed with other household wastes throughout
the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To return your used device, please use the local
recycle service or contact your point of purchase to withdraw the product.
·
the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
·Persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge must not use the appliance, unless
they're under supervision, understand the hazards involved or they have been thoroughly instructed in the use of the apparatus by a person
who is responsible for the safety of these persons.
·Don't leave the cords or plug unorganized in order to prevent tripping hazards.
·Any attempts to reconstruct the construction aren't allowed.
This appliance can be used by children aged from 8 years and above if they have been given supervision or instruction concerning use of
The product is powered by electricity. In order to avoid burns, fire and electric shock and make sure the safe and correct use
of the system and maintain the longevity of the overall construction and the built-in electronics, please read the instructions
carefully.
Electrical Safety Instructions
STEP1: When the mount is powered on, press the small button on the control box with a thin tool
as shown. The unit will emit a beep, indicating that the control box is on standby for
program coding.
STEP2: Press the “ ”button on the remote control, and you will hear repeated beeps for
approximate10 seconds indicating that the remote control is being programmed.
The unit will emit a beep again indicating success.
Note: Clear up the historical data when replacing a new remote control to pair. Press the small
button on the control box with hearing a beep, and hold for 5 seconds to confirm the
data-cleaning process is completed until you hear a beep again.
Remote Control Operation Instructions
A. Coding of Remote Control and Control Box
B. Button Functions
1.Upward/Downward Movement
Press and hold the " " button to lift the mount. Press and hold the " " button to lower the mount.
(Tips: Clear up all obstacles within the range of motion.)
2.Memory Setting
Long press the “ ” or “ ” button for 3 seconds until you hear a beep, indicating that the
current position has been saved to memory. The “ ” “ ” buttons can each store a
different position.
3.Recall Memory
Press the “ ” or “ ” button and the mount will automatically get to the position saved in the
corresponding button “ ” or “ ”.
4.Default Setting
Short press the “ ” button and the mount will automatically retract to the lowest position.
To stop it, press the “ ” button again.
5.Reset Mode
Long press the “ ” button for 3 seconds until you hear a beep, and the mount starts to move
downwards. Then the mount will move upwards a little bit when reaching the lowest position and
automatically come to a stop. The system resets successfully when the unit emits two beeps.
No te: The remote control is powered by two AAA batteries (not included).
·The appliance is only to be used with the power supply unit provided with the appliance. Alterations of the given power unit aren't allowed.
·Never operate the system with a damaged power supply cord or plug. If any parts is damaged, please contact your service agent of
purchase for a replacement.
·Never operate the system if it's in moist environment or its electrical components has contact with liquids.
·Don't clean the product while the power is still connected.
·Don't disassemble or replace components while the power is still connected.
·Unplug the appliance when the system isn't in use, and place the power plug out of children reach.
Troubleshooting Guide
In Front
This Troubleshooting Guide will assist you in identifying and solving common problems and answering questions you may have
about the product. Contact your place of purchase should the answer to your question or problem not be found in this
Troubleshooting Guide and/or for any after service parts and sales support.
1.Possible reasons motorized mount does not respond to remote control.
A.TV Mount
·
·The system may be overheating. Check if the unit beeps four times after pressing the button. If so, allow the unit to cool down and return
to room temperature. (about 30 minutes)
·The AC/DC end of the power cord may be unplugged/disconnect from the outlet/mount. Check the connection to ensure the unit
has power.
·Incorrect operation. Check if the unit beeps once after pressing the button. If so, please follow the instructions found in the manual to
properly operate the mount.
The system may be error. Check if the unit beeps three times after pressing the button. If so, please reset the system.
B.Remote Control
·
·The batteries in the remote control may be low or dead. Replace the batteries.
·The remote control may be broken. Check to see if the indicator LED found on the remote lights when a button is pressed.
If not, contact your place of purchase for a replacement.
The remote control operating distance may be too far and not in range of the mount. Acceptable range should be less than 30 feet (10m).
2.The TV mount stops moving during operation and emits a long beep.
·
·The weight of TV may exceed the maximum weight limitation of the mounting system.
·The motor wire may be broken. Reset the system. If the problem still exists, contact your place of purchase for replacement.
Check to see if a foreign object is impeding the mount from moving. If so, remove the object and discard.
3.The TV mount is making an abnormal noise or sound.
[Remote Specification] Frequency band(s):2437MHz | Receiver category: Type II | Transmitting power:2dBm
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
FCC Notice
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
·
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
· Consult the dealer or an experienced radio/TV technician for help. RF exposure warning
Reorient or relocate the receiving antenna.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed
and operated with minimum distance 20cm between the radiator & your body.
12
INSTALLATION MANUAL
Motorized TV Mount
LP66-46M
50kg
(110lbs)
RATED
Use with products heavier than the rated weights indicated may result in instability causing possible injury.
Please closely follow the assembly instructions. Improper installation may result in damage or serious personal injury.
Safety gear and proper tools must be used. This product should only be installed by professionals.
Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, contact your place of
purchase for a replacement.
Check that the product is secure and safe to use at regular intervals (at least every three months).
200x200/300x300
400x200/400x400
600x400
65"
MAX