Operations Manual

http://www.goodluckycn.com
FF1108-1CWLA fish finder Wireless
Mode Operations Manual
When FF1108-1CWLA powers on, the will temporarily
display on screen last for 5seconds.Then will
show ,From this menu, use the arrow keys to select either
Start-Up, Simulator.
FF1108-1CWLA Fish Finder Wireless
Mode Operations Manual
Thank you for choosing FF1108-1CWLA fish finder.
The FF1108-1CWLA has two different user modes:WIRELESS
/TRANSDUCER
Use the User Mode menu choice to change between these two
user modes.
WIRELESS:This user mode allows you to operate the FF1108-1CWLA
with the wireless sonar sensor. When signal indicator
is displayed on the screen, the unit is in Wireless mode.
Wireless sonar sensor signal
connect indicator
Display View
The FF1108-1CWLA displays underwater information in an easy-
to-understand format. The top of the display corresponds to
the water surface at the transducer, and the bottom of the
dis p lay corresponds to the Depth Range au tomatically
selected for the current water depth. The Bottom Contour
varies as the depth under the boat changes. Digital readouts
provide precise information for depth, fish and water
temperature.
As the boat moves, terrain and bottom composition variations
are displayed. Fish, baitfish and the rmoclines (underwater
Press the POWER-MENU key last for 5 seconds to power
FF1108-1CWLA on. Press and hold the POWER-MENU key
until the unit shuts down to power off.
Powering ON and OFF
Fish Alarm—
Press the POWER-MENU key until FISH ALARM appears.
Select Off for no fish alarm, or one of the following symbols to
set the alarm. An alarm will sound when the FF1108-1CWLA
detects fish that correspond to the alarm setting. Fish Alarm
will only sound if Fish ID+ is also set to On.
Make sure press the POWER-MENU key until FISH ICON
appears. Select either Off to view “raw” sonar returns, or On to
view Fish symbols. Fish ICON uses advanced signal processing
to interpret sonar returns, and will display a Fish Symbol when
very selective requirements are met.
Make sure press the POWER-MENU key UNITS appears.
UNITS selects the UNITS of (M/℃、FT/℃、M/℉ 、FT/℉ )
Units
Fish Icon
A select number of possible fish returns will be displayed with
their associated depth. (On, Off)
SPECIFICATIONS
Maintenance
Follow these simple procedures to ensure your FF1108-1CWLA
continues to deliver top performance. If the unit comes into
contact with salt spray, wipe the affected surfaces with a cloth
dampened in fresh water.
Do not use a chemical glass cleaner on the less-this may cause
cracking in the lens.
When cleaning the LCD protective lens, use a chamois and
non-abrasive, mild cleaner. Do not wipe while dirt or grease is
on the lens. Be careful to avoid scratching the lens.
Never leave the unit in a closed car or trunk - the extremely high
temperatures generated in hot weather can damage the
electronics.
After using the Wireless sonar sensor in salt water, wipe the
affected surfaces with a cloth dampened with fresh water. The
Wireless sonar sensor Cuprum-switch must be rinsed with fresh
water after exposure to salt water prevent corrosion.
If your Wireless sonar sensor remains out of the water for a
long period of time, it may take some time to wet it when returned
to the water. Small air bubbles can cling to the surface of the
Wireless sonar sensor and interfere with proper operation.
Wipe the face of the Wireless sonar sensor with a wet cloth to
remove them.
Wireless sonar sensor Maintenance
Wireless sonar sensor is placed back in the water and reception
is regained.
will be displayed until the
seconds, the
1) The Wireless sonar sensor uses line -of- sight wireless
technology. If objects are placed between the FF1108-1CWLA and
the Wireless sonar sensor, reception may be lost.
2) The Wireless sonar sensor depth range is 3 to 147 feet
(0.7 to 45 meters). Erratic readings may occur in water that is
shallower than 3 feet. In addition, because of the nature of
sonar, this product is not intended for use in swimming pools
or small enclosed bodies of water.
3) Reeling the Wireless sonar sensor too fast can cause loss
of signal and the screen will freeze.
4) Check the buoyant balance between the Wireless sonar
sensor and your tackle; over 0.2 ounce will submerge the
Wireless sonar sensor, causing signal loss.
5) The Wireless sonar sensor may not obtain its maximum RF
distance of 200 feet unless the water is smooth. Waves or chop
may reduce the RF range significantly.
2.When in very shallow water, I get gaps in the bottom reading
and inconsistent digital depth indication.
The Wireless sonar sensor will work reliably in water 3 feet
(0.7 meters) or deeper. The depth is measured from the
Wireless sonar sensor. A Wireless sonar sensor to FF1108-1CWLA
distance of greater than 200ft may cause intermittent screen
display. Excessively rough water may cause the Wireless sonar
sensor to submerge, again losing contact.
Fish finder power:… … …3.7 Volt rechargeable lithium battery
Wireless sonar sensor power :… … … …3. 7V Lithium Battery
Display Type … … … … … … … … … …320x240 TFT color LCD
Depth Capability… … … … … … … … … … … … … …3-147 feet
(0.7 – 45 meters)
。
Sonar Beam Angle… … … … … … … … … … … … … … … …90
Sonar Operating Frequency … … … … … … … … … …125kHz
Operational Wireless Frequency… … … … … … … 433.92MHZ
Operational Range … … … … … … … … 200feet (60meters)
.
·Use Start-Up for on the water use.
·Use Simulator for learning how to use the system with
simulated sonar data; access Simulator by pressing the Down
Arrow Key once
NOTE: Each time the POWER-MENU key is pressed, the
backlight momentarily illuminates for easy viewing at night.
Adjust the LIGHT menu setting to keep the backlight on.
temperature changes) are displayed when detected. Underwater
conditions vary greatly, so some experience and interpretation
is needed to realize all the benefits of the FF1108-1CWLA use
the picture as a guide to the most common conditions and
practice using the FF1108-1CWLA over known bottom types.
Display
User Mode
Left Arrow Key
Right Arrow Key
Power/MENU key
Never leave the Wireless sonar sensor in a closed car or trunk
-the extremely high temperatures generated in hot weather can
damage the electronics.
Trouble
1.The FF1108-1CWLA loses signal in wireless User Mode
.If the FF1108-1CWLA, while in Wireless user mode, is not able
to get an RF signal from the Wireless sonar sensor, the display
will stop updating and the NO SIGNAL will be displayed
after several seconds. Whenever reception is lost or the
Wireless sonar sensor pulled out from the water for more
than a few
sometimes a vertical line is missing or a black line from top to
bottom is displayed.
This screen image jump is due to an automatic change in depth.
New returns graphed at a different scale will not match up with
the historic data already graphed at a higher or lower scale.
Vertical lines can also occur as the radio signal from the
Wireless sonar sensor is lost and then regained in rough water
conditions.
3.The display shows fluctuating depth readings and excessive
clutter, including vertical bars that may be drawn on top of fish
icons.
4.The screen jumps and the bottom has an abrupt change;
This amazing product is especially designed for amateur and
professional fisherman alike, to find out the location of fish,
depth and bottom contour of water. The unit can be used in
ocean, river or lake,and is fantastic for detecting schools of fish
in any particular area.Using amazing and innovative technology,
this fish finder is the ideal tool to bring the fish to you!
The FF1108-1CWLA has two user modes: WIRELESS/SIMULATION.
A simple menu system allows you to access your FF1108-1CWLA
adjustable settings. To activate the menu system, press the
POWER-MENU key. Press the POWER-MENU key repeatedly
to display the FF1108-1CWLA menu settings,one at a time.When
a menu settings is on the display, use the UP and DOWN Arrow
keys to adjust the menu setting. Menus settings are removed
from the screen automatically after several seconds. In Normal
operating mode, most menu settings saved to memory.
(Off, large fish only, Large fish/Small fish).
Battery Strength Indicator
Sensor Connect Indicator
Water Depth
Water Temperature
Large Fish Icon With Depth
Bottom C ontour
Depth upper limit
Water Surface Line
Samll Fi sh Icon With Depth
Depth low limit
Sensitivy
W-Sensor Battery Indicator
W-Sensor
a. Charging the sensor
b. Using the sensor
Switch 1 for W-Sensor
Working Indicator
Charging Port
Switch 2 for fish attractive lamp
Charging Indicator
1. Press Switch 1, wireless sensor
will be turned on, and working
Indicator will be lit.
pic1 pic2
pic3
2. Press Switch 2, fish attractive
lamp will be turned on, and fish
attractive light will be lit.
3. Please screw down the lid to
prevent water come in.
4. Tie the fishing line to the hole of W-sensor, and cast it to the water.
Press the POWER-MENU key until SENSITIVITY appears.
Sensitivity controls how much detail is shown on the display.
Increasing the sensitivity shows more sonar returns from small
baitfish and suspended debris in the water; however, the display
may become too cluttered. When operating in very clear water
or greater depths, increased sensitivity shows weaker returns
that may be of interest. Decreasing the sensitivity eliminates
the clutter from the display that is sometimes present in murky
or muddy water. If Sensitivity is adjusted too low, the display may
not show many sonar returns that could be fish. (1 –10).
Press the POWER-MENU key until Depth low limit appears.
Automatic is the default setting. When in automatic, the lower
range will be adjusted by the unit to follow the bottom.
(Auto, 1 to 45 meter)
Depth upper limit—
Press the POWER-MENU key until Depth upper limit appears. Select
Auto to magnify the area around the bottom in order to reveal fish and
structure close to the bottom that may not be visible during normal
operation. When Depth upper limit is set to Auto, the upper and lower
Depth Ranges are automatically adjusted to keep the area above and
below the bottom on the display. Select Off to return to normal
operation. (Off, 1 to 45 meter).
NOTE: In manual operation, if the current depth is greater than
the depth range settings, the bottom will not be visible on the
display. Select AUTO to return to automatic operation.
There is also a series of manual ranges which can be selected.
The manual depth ranges are determined by the present depth
conditions.
Depth low limit—
Shallow alarm
Press the POWER-MENU key until SHALLOW ALARM appears.
Select OFF for no Shallow Alarm, or select 1 to 45 meter to set
the alarm depth. An audible alarm sounds when the depth is
equal to or less than the setting. (Off, 1 to 45meter)
Depth upper limit
Bottom Contour
Depth low limit
Language—
Press the POWER-MENU key until LANGUAGE appears.The
FF1108-CW fish finder has two language choice(English,Russian)
Brightness
Press the POWER-MENU key until BRIGHTNESS appears.
Use the backlight for night fishing. Select either Off, or On to
activate the backlight at the desired level.
Sensitivity—
Start up
Start up
Language
English
Brightness
5
Sensitivity
5
Depth low limit
Auto
Depth upper limit
off
Shallow alarm
off
Fish alarm
off
Units
M / ℃
User mode
Wireless
User mode
Simulation
Fish icon
off
Fish icon
On
Fish icon
off
Start up
Start up
User mode
Simulation
MADE IN CHINA
MANUFACTURER: JINHUA LUCKY ET MANUFACTURER CO.,LTD.