5 GHz Subscriber Station Model: LTU-LR
Introduction Thank you for purchasing the Ubiquiti® LTU™ 5 GHz Subscriber Station. This Quick Start Guide is designed to guide you through installation and also includes warranty terms. Package Contents LTU-LR U-Bolt Mount Bracket Flange Nuts (Qty. 2) Gigabit PoE (24V, 0.5A) with Mounting Bracket Pole Clamp Washers (Qty.
Hardware Overview Back Panel Reset Button USB-C Port LEDs Reset Button To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the device is powered on. USB-C Port Reserved for future use. LEDs 5 GHz 5 GHz The LED will light blue when the 5 GHz link is active. GPS GPS The LED will light blue when the GPS signal strength is sufficient. This requires a minimum of three satellite connections.
Bottom Panel Ethernet Port Ethernet Port Gigabit PoE port for handling all user traffic and powering the device. Default IP address: 192.168.1.
Pole Mounting 1. Remove the lock nut. 2. Attach the Mount Bracket.
3. Replace the lock nut. 4. Insert the U-Bolt into the Pole Clamp.
5. Insert the U-Bolt into the Mount Bracket. Secure the U-Bolt with the Washers and Flange Nuts.
6. Aim the device, and then lock the aim by tightening the Flange Nuts to a torque of 25 N ∙ m.
Connecting Power 1. Remove the port cover by pressing down the center of the cover and sliding the cover out. 2. Connect an Ethernet cable to the Ethernet port.
3. Replace the port cover. 4. Connect the power using one of the following options: • Using the included Gigabit PoE Adapter: Go to Connecting to the PoE Adapter. • Using a separate PoE switch: Connect the Ethernet cable from the device’s Ethernet port to a 24V Passive PoE-enabled Ethernet port on the switch. WARNING: The switch port must comply with the power specifications listed in the Specifications section of this Quick Start Guide.
Connecting to the PoE Adapter 1. Connect the Ethernet cable from the device to the POE port of the Gigabit PoE adapter. 2. Connect an Ethernet cable from your LAN to the LAN port of the Gigabit PoE adapter. 3. Connect the Power Cord to the Gigabit PoE adapter. Connect the other end of the Power Cord to a power outlet. Mounting the PoE Adapter (Optional) 1. Remove the PoE Mounting Bracket from the adapter, place the bracket at the desired location, and mark the two holes. 2.
Accessing the Configuration Interface 1. Make sure that your host system is connected via Ethernet to the device. 2. Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet. 3. Launch your web browser and type https://192.168.1.20 in the address field. Press enter (PC) or return (Mac). https://192.168.1.20 4. Enter ubnt in the Username and Password fields. Select your Country and Language. You must agree to the Terms of Use to use the product. Click Login.
Installer Compliance Responsibility Devices must be professionally installed and it is the professional installer’s responsibility to make sure the device is operated within local country regulatory requirements. Since Ubiquiti equipment can be paired with a variety of antennas and cables, the Output Power field is provided to the professional installer to assist in meeting regulatory requirements.
Specifications LTU-LR Dimensions 316.5 x 316.5 x 174.3 mm (12.46 x 12.46 x 6.86") Weight 1.3 kg (2.87 lb) Networking Interface (1) 10/100/1000 Ethernet Port Enclosure Outdoor UV Stabilized Plastic Max. Power Consumption Power Supply 9W 24V, 0.
Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in a location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Electrical Safety Information 1. Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturer’s label.
Compliance FCC Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
CAN ICES-3(A)/NMB-3(A) Le présent appareil est conforme aux CNR d’ISDE Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1. l’appareil ne doit pas produire de brouillage; 2. l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Le présent émetteur radio (IC: 6545A-LTU5S) a été approuvé par ISDE Canada.
Brazil Nota: Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente autorizados. CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it. Country List AT BE BG CY CZ DE DK EE IE IT LV LT EL ES FI LU MT NL PL PT RO SE FR HR HU SI SK UK BFWA (Broadband Fixed Wireless Access) members noted in blue Note: This device meets Max.
RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities.
Español La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
Declaration of Conformity български [Bulgarian] С настоящото UBIQUITI декларира, че това устройство LTU-LR е в съответствие със съществените изисквания и други приложими разпоредби на Директиви 2014/53/EC, 2014/30/ЕС, 2014/35/ЕС. Цялостният текст на ЕС декларацията за съответствие може да се намери на следния интернет адрес: ui.
Italiano [Italian] Con la presente, UBIQUITI, dichiara che questo dispositivo LTU-LR, è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti delle direttive 2014/53/UE, 2014/30/UE, 2014/35/UE. Il testo completo della dichiarazione di conformità UE è disponibile al seguente indirizzo Internet: ui.
Ubiquiti Inc. 685 Third Avenue, 27th Floor New York, NY 10017 USA ©2019 Ubiquiti Inc. All rights reserved. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, airMAX, airOS, LTU, and UNMS are trademarks or registered trademarks of Ubiquiti Inc. in the United States and in other countries. Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc., registered in the U.S.