User's Manual

2
Wall Mounting:
The figures are for reference only.
You can also install the device on the wall or
other places without the gang box. For
details, refer to the User Manual.
Direct
Sunlight
Direct Sunlight
through Window
Backlight
Indirect Sunlight
through Window
Close to Light
1
Make sure the gang box is installed on the wall.
3
plate and hang the terminal on the
4
Use 1 supplied screw (SC-KM3X6-H2-SUS)
5
Apply Silicone sealant among the joints
between the device rear panel and the
wall (except the lower side) to keep the
raindrop from entering.
Use 2 supplied screws (SC-K1M4×6-SUS) to secure the base plate
on the gang box.
and connect to the corresponding external devices’ cables.
Use another 4 supplied screws (KA4×22-SUS)to secure the
Installation Environment:
indoors, the device should be at least 2 meters away from the light, and at
least 3 meters away from the window or the door. If installing the device
outdoors, you should apply Silicone sealant among the device to keep the
raindrop from entering.
microUSB Interface
(Use micro USB to USB cable
to connect with USB interface)
CameraCamera
Debugging Port
(For debugging only)
Tamper
Wiring
Terminal
Network
Interface
Screen
IR Light IR Light
White Light
22.7 mm
83.2 mm
12.3 mm
172.5 mm
Mic
LTK3410MF
Face Recognition Terminal
Quick Start Guide
Make sure the power supply is used indoors, and the working
temperature is between 0 and 40 °C.
The Wiegand termimal here is a Wiegand input
connect to an access controller, you should
The suggested external power supply for door lock
is 12 V, 1A.
The suggested external power supply for Wiegand
card reader is 12 V, 1 A.
For wiring the fire system, see the user manual.
you can use the supplied cable as shown below.
Connect
Network
Interface of
Device
Connect
Network
Cable
Model Manufacture Standard
ADS-26FSG-12 12024EPG Shenzhen Honor Electronic Co.,Ltd PG
MSA- C2000IC12.0-24P- DE MOSO Technology Co.,Ltd PDE
ADS-26FSG-12 12024EPB Shenzhen Honor Electronic Co.,Ltd PB
ADS-26FSG-12 12024EPCU/EPC Shenzhen Honor Electronic Co.,Ltd PCU
ADS-26FSG-12 12024EPI-01 Shenzhen Honor Electronic Co.,Ltd PI
ADS-26FSG-12 12024EPBR Shenzhen Honor Electronic Co.,Ltd PBR
RS-485
Wiegand
Door Lock
Network Interface
Power Input
GND
GND
GND
GND
BTN
12V External
Power Supply
Wiegand
Card Reader
Group B
Group D
B1
B2
B3
C1
C2
C3
D6
D7
D1
D2
D3
D4
D5
(NC)
(COM)
(NO)
Eletric Dropbolt
Power Supply
Eletric Strike
Door Contact
Exit Button
White/Black
White/Purple
White/Yellow
White/Red
Yellow/Green
Yellow/Gray
Yellow/Black
Black
Red/Black
Black
Yellow
Green
White
Blue
Red
NO
COM
NC
NO
COM
NC
1
Installation
2
Appearance
3.1
Device Wiring (Normal)
Loudspeaker
This sticker means“Hot parts! Burned fingers
when handling the parts. Wait one-half hour after
switching off before handling parts.”It is to
indicate that the marked item can be hot and
should not be touched without taking care. For
device with this sticker, this device is intended for
installation in a restricted access location, access
can only be gained by service persons or by users
who have been instructed about the reasons for
the restrictions applied to the location and about
any precautions that shall be taken.