Network PTZ Camera·Quick Start Guide Network PTZ Camera Quick Start Guide i
Network PTZ Camera·Quick Start Guide Quick Start Guide About this Manual This Manual is applicable to Network PTZ Camera. The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version in the company website.
Network PTZ Camera·Quick Start Guide SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, OUR COMPANY WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW.
Network PTZ Camera·Quick Start Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Network PTZ Camera·Quick Start Guide 2015/35/EU, the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information, please see: www.recyclethis.info.
Network PTZ Camera·Quick Start Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected. Warnings Follow these safeguards to prevent serious injury or death.
Network PTZ Camera·Quick Start Guide Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard. Make sure that the plug is firmly connected to the power socket. Make sure that the power has been disconnected before you wire, install or dismantle the PTZ camera. When the product is mounted on wall or ceiling, the device shall be firmly fixed.
Network PTZ Camera·Quick Start Guide Do not touch senor modules with fingers. If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an extended period, replace the lens cap to protect the sensor from dirt. Do not aim the camera at the sun or extra bright places. Blooming or smearing may occur otherwise (which is not a malfunction), and affect the endurance of sensor at the same time.
Network PTZ Camera·Quick Start Guide Table of Contents 1 Overview ....................................................................... 9 1.1 Introduction ............................................................................. 9 1.2 Cable Descriptions .................................................................... 9 1.3 Alarm Output.......................................................................... 10 2 Installation .................................................................
Network PTZ Camera·Quick Start Guide 1 Overview 1.1 Introduction The network PTZ camera has the following series: PTZIP2XX Series PTZ Camera PTZIP4XX Series PTZ Camera Integrated with an optical zoom lens, this series of cameras feature in the PTZ limits, 3D positioning, Day/Night auto switch, 3D DNR, etc., and are widely applied in various kinds of environments. 1.2 Cable Descriptions The cable interfaces of network PTZ camera are shown in Figure 1-1.
Network PTZ Camera·Quick Start Guide Power Cord DC12V IN Video Cable RS-485 Alarm Cable .. Audio Cable Network Cable Figure 1-1 Cables of PTZ Camera Power Cord: Supports 12 VDC power supply. Video Cable: Connect BNC Cable to test the video output. Alarm Cable: Connect terminal ALARM-IN with GND interface, and connect terminal ALARM-OUT with ALARM-COM interface. Audio Cable: Connect terminal AUDIO-IN with GND interface.
Network PTZ Camera·Quick Start Guide GND Output DC 30V 1A Power Supply JQC-3FG Relay (10A 250VAC) Direct load Relay Output OUT (n) OUT (n) + DC - ~220V AC Relay Output OUT (n) OUT (n) Figure 1-2 Alarm Output 11 FireWire Zero Line
Network PTZ Camera·Quick Start Guide 2 Installation Before you start: Check the package contents and make sure that the device in the package is in good condition and all the assembly parts are included. Notes: Do not drag the PTZ camera with its waterproof cables; otherwise the waterproof performance is affected. Do not touch the bubble directly by hand. The image blurs otherwise. Do not power up the camera until the installation is finished.
Network PTZ Camera·Quick Start Guide Crack Cover 2.0 Figure 2-1 Open the Cover 2. Unscrew the screws on the camera base with the cross screwdriver, and remove the bubble, as shown in Figure 2-2. Bubble Screw Figure 2-2 Remove the Bubble 3. Open the memory card slot in the camera, and insert the memory card.
Network PTZ Camera·Quick Start Guide 4. Align the bubble with the camera base, and install the bubble back. Fix the bubble with four M4×10 screws, as shown in Figure 2-3. Figure 2-3 Install the Bubble 5. Align the cover with the camera, and install the cover back, as shown in Figure 2-4.
Network PTZ Camera·Quick Start Guide 2.1.2 PTZIP4XX Series PTZ Camera Steps: 1. Remove the four silicone plugs on the decorative rim as shown in Figure 2-5, and you can see four flange screws in the decorative rim. Silicone Plug Decorative Rim Figure 2-5 Remove the Silicone Plugs 2. Loosen four flange screws with a screwdriver. Remove the bubble and the decorative rim as shown in Figure 2-6.
Network PTZ Camera·Quick Start Guide 3. Open the memory card cover and insert the memory card into the card slot as shown in Figure 2-7 and Figure 2-8. Memory Card Slot Memory Card Cover Figure 2-7 For 20× Camera Module Memory Card Slot Memory Card Cover Figure 2-8 For 4× Camera Module 4. Close the memory card cover. Fix the four flange screws and push four silicone plugs back to assemble the PTZ camera. 2.2 Installing PTZIP2XX Series PTZ Camera 2.2.
Network PTZ Camera·Quick Start Guide The thickness of the ceiling shall range from 5 mm to 40 mm. Make sure the ceiling is strong enough to withstand more than four times the weight of the PTZ camera and its accessories. Steps: 1. Rotate the installation plate anticlockwise, and remove the installation plate, as shown in Figure 2-9. OPEN Installation Plate Figure 2-9 Remove the Installation Plate 2. Drill four screw holes in the ceiling according to the installation plate. 3.
Network PTZ Camera·Quick Start Guide Figure 2-10 Fix the Installation Plate 4. Route the cables from the cable hole in the installation plate. 5. Align the camera with the installation plate, and rotate the camera clockwise to fix it, as shown in Figure 2-11.
Network PTZ Camera·Quick Start Guide 2.2.2 Wall Mounting Notes: For cement wall, you need to use the expansion screw to fix the bracket. The mounting hole of the expansion pipe on the wall should align with the mounting hole on the bracket. For wooden wall, you can just use the self-tapping screw to fix the bracket. Make sure that the wall is strong enough to withstand more than eight times the weight of the PTZ camera and its accessories. Steps: 1.
Network PTZ Camera·Quick Start Guide Fixing Screw Bracket Base Figure 2-13 Remove the Bracket Base 3. Install the bracket base on the wall with four PA4×25 screws. Figure 2-14 Install the Bracket Base 4. Route the cables. Align the camera with the installation plate on the wall mounting bracket, and rotate the camera clockwise to fix it on the bracket.
Network PTZ Camera·Quick Start Guide 5. Connect the cables. Install the wall mounting bracket to the bracket base on the wall, and fix it with the supplied PM4×10 screw. Figure 2-16 Fix the Bracket 6. Remove the protective film after installation. 2.3 Installing PTZIP4XX Series PTZ Camera PTZIP4XX series (IR) PTZ camera supports ceiling mounting and in-ceiling mounting. Note: Wall mounting, pendant mounting, and installation with junction box are supported for PTZIP4XX series (IR) PTZ camera.
Network PTZ Camera·Quick Start Guide The ceiling mounting is applicable to the indoor/outdoor solid ceiling construction. The followings are the mandatory precondition for ceiling mounting: The thickness of the ceiling shall range from 5 mm to 40 mm. Make sure the ceiling is strong enough to withstand more than four times the weight of the PTZ camera and its accessories.
Network PTZ Camera·Quick Start Guide Ceiling Mounting without Junction Box 1. Rotate the base plate counterclockwise to separate it from the PTZ camera, as shown in Figure 2-19 and Figure 2-20. OPEN Base Plate on the Bottom of the Dome Front View of Base Plate Figure 2-19 Base Plate for PTZIP4XX Series PTZ Camera OPEN Base Plate on the Bottom of the Dome Front View of Base Plate Figure 2-20 Base Plate for PTZIP4XX Series (IR) PTZ Camera 2.
Network PTZ Camera·Quick Start Guide Figure 2-21 Attach the Drill Template 3. Drill a cable hole in the ceiling according to the circle A on the template if you want to route the cables through the ceiling. Pull out the cable slot cover if you want to route the cables on the surface of the ceiling, as shown in Figure 2-22.
Network PTZ Camera·Quick Start Guide Cable Slot Cover Figure 2-23 For PTZIP4XX Series (IR) PTZ Camera 4. Attach the base plate to the ceiling and secure it with the supplied three self-tapping screws by aligning with three screw holes in the ceiling, and the front arrows on the drill template and base plate should be aligned together as well, as shown in Figure 2-24 and Figure 2-25.
Network PTZ Camera·Quick Start Guide Figure 2-25 For PTZIP4XX Series (IR) PTZ Camera 5. Route the cables through the cable hole. 6. Align the PTZ camera with the base plate. Rotate the PTZ camera clockwise into the base plate, and the PTZ camera is secured with the base plate by three locks on the plate.
Network PTZ Camera·Quick Start Guide After PTZIP4XX series (IR) PTZ camera is installed, tighten the fixing screw with a screwdriver as shown in Figure 2-27. Fixing Screw Figure 2-27 Tighten the Fixing Screw 2.3.2 In-ceiling Mounting Notes: Reserve at least 250 mm of height for in-ceiling mounting. The thickness of the ceiling shall range from 5 mm to 40 mm. Make sure the ceiling is strong enough to withstand more than four times the weight of the PTZ camera and its accessories Steps: 1.
Network PTZ Camera·Quick Start Guide Separate the Base Plate from the PTZ Camera Rotate Counterclockwise Figure 2-28 Separate the Base Plate from the PTZ camera Ø 2. Attach the drill template (supplied) to the place where you want to fix the PTZ camera, and drill a hole in the ceiling according to the template. 2 21 Figure 2-29 Drill Template 3.
Network PTZ Camera·Quick Start Guide Figure 2-30 Fix the Base Plate to In-ceiling Bracket 4. Connect the cables and route the cables through the cable hole. 5. Align the PTZ camera with the base plate. Rotate the PTZ camera clockwise into the base plate, and the PTZ camera is secured with the base plate by three locks on the plate. 6. Fix the screws on the side with a screwdriver, as shown in Figure 2-31.
Network PTZ Camera·Quick Start Guide 7. Place the camera and the bracket into the hole drilled in step 2, and rotate the screws clockwise to fix the camera. 8. Fix the decorative rim with the bubble and the decorative rim will be attached to the in-ceiling bracket automatically, as shown in Figure 2-32.
Network PTZ Camera·Quick Start Guide 3 Setting the PTZ Camera over the LAN Notes: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, strengthen your own protection. If the product does not work properly, contact with your dealer or the nearest service center. To ensure network security of the network PTZ camera, we recommend you to have the camera assessed and maintained termly.
Network PTZ Camera·Quick Start Guide or Cab ork tw Ne le 网络交换机 Network PTZ Camera Ne two rk Cab le Computer Figure 3-2 Connecting via a Switch or a Router 3.2 Activating the Camera Purpose: You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via web browser, activation via IP PORTAL, and activation via client software are supported.
Network PTZ Camera·Quick Start Guide Notes: The default IP address of the camera is 192.0.0.64. The computer and the camera should belong to the same subnet. Figure 3-3 Activation Interface (Web) 3. Create a password and input the password into the password field.
Network PTZ Camera·Quick Start Guide 5. Click OK to activate the camera and enter the live view interface. 3.2.2 Activation via IP PORTAL Software IP PORTAL software is used for detecting the online device, activating the device, and resetting the password. Get the IP PORTAL software from the supplied disk or the official website, and install the IP PORTAL according to the prompts. Follow the steps to activate the camera. Steps: 1. Run the IP PORTAL software to search the online devices. 2.
Network PTZ Camera·Quick Start Guide The IP PORTAL software supports activating the camera in batch. Refer to the user manual of IP PORTAL software for details. 3. Create a password and input the password in the password field, and confirm the password.
Network PTZ Camera·Quick Start Guide PORTAL software as an example to introduce the IP address modification. Note: For IP address modification via client software, refer to the user manual of client software. Steps: 1. Run the IP PORTAL software. 2. Select an active device. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the Enable DHCP checkbox.
Network PTZ Camera·Quick Start Guide Figure 3-5 Modify the IP Address 4. Input the admin password and click Modify to activate your IP address modification. The batch IP address modification is supported by IP PORTAL. Refer to the user manual of IP PORTAL for details.
Network PTZ Camera·Quick Start Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version/Vista/Win7/Server 2003/Server 2008 32bits CPU: Intel Pentium IV 3.0 GHz or higher RAM: 1G or higher Display: 1024 × 768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.02 and above version, Mozilla Firefox 5 and above version and Google Chrome 18 and above version Steps: 1. Open the web browser. 2.
Network PTZ Camera·Quick Start Guide 4. Click Login. Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the network PTZ camera. Follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in.
Network PTZ Camera·Quick Start Guide 6. Reopen the web browser after the installation of the plug-in and repeat the above steps 2-4 to login. Note: For detailed instructions of further configuration, refer to the user manual of the network camera.
