User Manual

ManualsBrandsLS ELECTRIC ManualsElectronicsMotor control racking system

VCB CRADLE CONTROLLER

AND WIRED REMOTE CONTROL

<U-MCRS> MANUAL

1. RATING SPEC

1) SPEC

No. Classification RATING

1 Control Power AC 84~270V, DC 84~280V (Free voltage)

2 Motor

1. AC120(DC125)  DC110V Motor

2. AC240V(DC250)  DC220V Motor

3 Rating Frequency 1. 50/60Hz

4 SIZE

1. CONTROLLER: INCLUDE CASE

415(W)ⅹ257(D)ⅹ73(H)

Main PCB 330(W)ⅹ200(D)ⅹ40(H)

Relay PCB 110(W)ⅹ62(D)ⅹ35(H)

2. WIRED REMOTE CONTROL:

209.3(W)ⅹ84.1(D)ⅹ38.4(H)(mm)

PCB 200(W)ⅹ75(D)ⅹ25(H)

5 Communication Port

Ethernet Port 3ea

(Communication Remote control Modbus

/ PLC Connecting)

6 Communications Protocol

MODBUS

(According to the LS electric MODBUS Standard)

Quantity of MODBUS

Address

Rotary Switch 3ea (Total : 259ea)

2) Products Image

3) Function

Drive the DC motor to move the VCB position to Disconnect, Test Connect by receiving an

operation command through wired remote control communication and when an error occurs

Controller and wired remote control capable of sending error messages

4) Hardware spec

Summary of content (7 pages)

PAGE 1
VCB CRADLE CONTROLLER AND WIRED REMOTE CONTROL MANUAL 1. RATING SPEC 1) SPEC No. Classification 1 Control Power 2 Motor 3 Rating Frequency 4 SIZE 5 Communication Port 6 Communications Protocol 7 Quantity of MODBUS Address RATING AC 84~270V, DC 84~280V (Free voltage) 1. AC120(DC125)  DC110V Motor 2. AC240V(DC250)  DC220V Motor 1. 50/60Hz 1. CONTROLLER: INCLUDE CASE 415(W)ⅹ257(D)ⅹ73(H) Main PCB 330(W)ⅹ200(D)ⅹ40(H) Relay PCB 110(W)ⅹ62(D)ⅹ35(H) 2. WIRED REMOTE CONTROL: 209.3(W)ⅹ84.
PAGE 2
① ② CPU: STM32F107VCT7 Memory : Flash Memory 256KB 5) Input Terminal (1) 8 Pin Connecter Terminal - Location Check Cell Switch: 6Pin - VCB Presence check Cell Switch: 2Pin (2) 8 Pin PCB Terminal (250V, 20A or more) - For MOC Close signal input: 2Pin - For MOC Open signal input: 2Pin - For Checking manual withdrawal operation Cell switch: 2Pin - For FG (Frame Ground) Terminal: 1Pin (3) 3 Pin PCB Terminal - Input Power Line (+, FG, -): 3Pin (4) 2 Pin PCB Connector - Motor Power Line: 2Pin (5) 2 Pin PCB Term
PAGE 3
(7) (8) Motor position check Cell switch signal(contact) connection Cell Switch(GPIO) signal(contact) connection for user selection (Do not connect in basic use) (9) Check whether PLC connection terminal  Do not connect when using remote control (10) Remote control connection (11) VCB CLOSE signal contact connection (12) VCB OPEN signal contact connection 7) Standard operating environment (1) Use temperature: -30℃ ~ +70℃ (Constant driving conditions) (2) Storage temperature: -40℃ ~ +70℃ (3) Annual average
PAGE 4
Display indication Error content standard Response in case of error E00 Press Stop/Reset Button When you press the Stop/Reset Button All buttons except the Reset button are disabled E01 Motor overcurrent (15A) MAX 15A or higher (requires actual measurement) All buttons except the Reset button are disabled E02 Motor overheating 20 times of continuous operation within 20 minutes All buttons except the Reset button are disabled E03 Motor operation time exceeded 45 seconds All buttons except
PAGE 5
< Outside > < Inside > (1) RS485 communication default (for basic installation) No.1,2 switch OFF / Device(in case of terminal installation) No.1,2 switch ON (2) When using Cell Switch(GPIO) for user selection, No.1,2 switch ON (3) Modbus communication address setting : 0~225ch setting (When channel 15 is set, 0: 1: 5 is set from the left rotary switch) (4) RS485 communication speed setting ① 9600bps  Rotary switch No.0 ② 19200bps  Rotary switch No.1 ③ 38400bps  Rotary switch No.
PAGE 6
live wire status) → U-MCS JIG Close button OFF → U-MCS JIG Open button ON → Representation of DOT LED 'E05' on the remote control (normal) ② Test by changing only the remote control button and U-mcrs jig Contact signal in the same way as the test location movement and operation test connect ③ Remote control Stop/Reset button(logic test) - Press the Stop button on the remote control → Representation of DOT LED 'E00' on the remote control → Press Stop button for 3 seconds → Representation of DOT LED 'LS' on
PAGE 7
The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.