of 20 Guide to the SRX 600 Keypad and LCD Display Revision D, #10055, March 16th, 2005
of 20 UNDERSTANDING THE LCD/KEYPAD LAYOUT The keypad and LCD display define the interface through which the receiver is programmed. The program is designed like a hierarchy. All aspects of the program are accessed through keys on the keypad. Keys labelled Setup, Log On, Info, Manual, Codelog and Set Delta provide access to menus (note that in most cases there are also sub-menus). Three of these keys are referred to as modes: Setup, Manual and Codelog.
of 20 Log On ILogging on to the receiver provides the ability to change the state of the receiver. When a log on password is provided the receiver is considered Online. If no password is provided (logged off) then the receiver is Offline. The differences between Online and Offline are described below: • Offline: the receiver allows only read access, which means that most inputs are not allowed unless a log on password is provided. The only input allowed is the Reset Password function.
of 20 Setup mode (1): 1)115200 2)57600 3)38400 4)19200 5)9600 6)4800 7) 2400 8)1200 9) 600 SERIAL BAUD RATE 1) Serial I 2) Serial II ##: 1)BAUD RATE 2) PARITY 3) DATA BITS 4) STOP BITS 5)MODEM SERIAL 1) Baud Rate 2) Parity CONFIGURE COMM: 1) Configure 1)SERIAL I 2) SERIAL II SERIAL PARITY(1): 1)NONE 2)ODD 3)EVEN 3) Data Bits SERIAL DATA BITS(2): 1) 7 BITS 2) 8 BITS 4) Stop Bits SERIAL STOP BITS(1): 1) 1 BIT 2) 2 BITS 5) Modem MODEM 1) HAS MODEM 2) VIEW CMDS 3) INITIALIZE SETUP: 1)COMM 2)TIM
of 20 1) GMT Correction 2) Time TIME (11:24:33 17/06/04): 1)GMT CORRECTION 2)LOCAL DATE 3)LOCAL TIME 2) Local Date GMT CORRECTION (-05:00): (HH:MM) > -- LOCAL DATE (17/06/04): (DD/MM/YY)> 3) Local Time RESET PASSWORD (630387): 3) Reset/Change Password (XXXXXX)> OR LOCAL TIME (11:24:33): (24HH:MM:SS)> CHANGE PASSWORD (******): (OLD/NEW)> Revision D, #10055, March 16th, 2005
of 20 Manual mode 1) Code Set MANUAL: 2)SEARCH CODE SET(1): 1)LOTEK 2 2)LOTEK3 3) LOTEK4 OR CODE SET: LOTEK 2 1)CODE SET 3)SIGNAL 2) Search ... see page 7 3) Signal ...
of 20 Manual Mode > 2) Search SEARCH 148.220MHZ ID AH0=40 0) PAUSE SCAN 1) CODE SET 2)SHOW BEEP/ID/SENSOR 3)SET 4)GPS 5) INC. FREQ. 6)DEC. FREQ. 7)EN/DIS NOISE BLANK 8) INC. GAIN 1) Start SEARCH (FROM 148.516MHZ): 1)START 2)GAIN 3)MIN FREQ 4)MAX FREQ 5)FREQ STEP 6)SCAN TIME 7)NOISE THRESHOLD 2)Gain 3)Min Freq 4)Max Freq 5)Freq Step 6)Scan Time 7)Noise Threshold 0)Pause Scan 9)DEC. GAIN FOUND: I184 S121 10:54:21 148.
of 20 Manual Mode > 3) Signal 1)START 2)GAIN 3)ANT 4)FREQ 5)NOISE THRESHOLD 1)Start SIGNL: I999 S102 11:13:46 148.220MHZ ID AH0=40 1) CODE SET 2)SHOW BEEP/ID/SENSOR 3)SET DELTA 4)GPS 5) INC. FREQ. 6)DEC. FREQ. 7)EN/DIS NOISE BLANK 8) INC. GAIN 9)DEC. GAIN 2)Gain GAIN(87): (00-99)> SIGNAL: 3)Ant ANT(0): (AH0=0, ASP8=1-8)> RADIO FREQ(149.010MHZ): 1)Radio (148-152.000MHZ)> 4)Freq FREQ(149.
of 20 Codelog Mode 1)Config(#1) ... see page 10 CODELOG: 1)CONFIG# 2)SCAN 3)MASTER FTABLE 2)Scan ... see page 16 3) Master FTable ...
of 20 Codelog Mode > 1)Config#1 NEW CFG#(3): 1)New Cfg# (1-8)> 1)Radio ADD RADIO FERQ(#11): (148-152.000MHZ)> ADD FREQ/CH: 1)Add 1)RADIO 2)ACOUSTIC 1)Config(#1) CONFIG(#3): 1)NEW CFG# 2)SCAN SETTINGS 3)FREQ/CH 4)ANT/HYDR 5)FILTERS 6)SENSORS FREQ/CH 2)Acoustic (10): 3)Freq/CH 1)ADD 2)VIEW/MODIFY 3)VIEW/MODIFY ALL 2)View/Modify 2)View/Modify All 2)Scan Settings ... see page 11 4)Ant/Hydr ... see page 12 5)Filters ... see page 13 6)Sensors ...
of 20 Codelog Mode > 1)Config#1 > 2)Scan Settings 1) Code Set CODE SET(1): 1)LOTEK2 2)LOTEK3 3)LOTEK4 1) Scan Time SCAN SETTINGS: SCAN TIME(18.1S): (00.1-99.
of 20 Codelog Mode > 1)Config#1 > 4) Ant/Hydr 1)Use ASP8 USE ASP8 1)YES 2)NO RADIO ANT GRP(123): (1-8)> 3)Ant 4)Ant/Hydr ANT/HYDR: 1)USE ASP8 2)GAIN 3)ANT 4)HYDR 5) PRIORITY ANT: 1)RADIO ANT GRP 2)RADIO MASTER ANT RADIO MASTER ANT(9): (GRP=0 ASP8=1-8 NO=9)> HYDR GRP(567): (1-8)> 4)Hydr HYDR:1)ACOUSTIC HYDR GRP 2)ACOUSTIC MASTER HYDR ACOUSTIC MASTER HYDR(0): (GRP=0 ASP8=1-8 NO=9)> 1)ASP8 Gain 2)Gain GAIN: 1)ASP8 GAIN 2)AH0 ANT GAIN 3)RADIO MASTER GAIN 4)ACOUSTIC MASTER GAIN 2) AH0 ANT Gain 3)
of 20 Codelog Mode > 1)Config#1 > 5)Filters 1) ID Filter FILTERS: FILTER: 1)FILTER TYPE 2)SET REJECT CH/ID 3)SET ACCPET CH/ID 4)SET REJECT ID 5)SET ACCEPT ID 1) Filter Type FILTER TYPE (3): 1)NO FILTER 2)REJECT CH/ID 3)ACCEPT CH/ID 4)REJECT ID 5)ACCEPT ID 1)ID FILTER 1) Add ADD REJECT CH/ID (#33): (XXX/XXX)> REJECT CH880 ID110 (#20): ADD ACCEPT CH/ID (#21): 2) View/Del 1)DEL 5) Filters 2)PULSE FILTER 2) Set Reject CH/Id SET REJECT CH/ID (32): 1)ADD 2)VIEW/DEL 1) Add 2) View/Del 3) Set
of 20 Codelog Mode > 1)Config#1 > 5)Filters > 2)Pulse Filter 1) Echo 2) Noise Threshold 2) Pulse Filter ECHO FILTER (020MS): (000-255)> NOISE THRESHOLD (30): (00-99)> PULSE FILTER: 1)ECHO 2)NOISE THRESHOLD 3)PULSE WIDTH 4)SIGNAL STRENGTH DEV 2.
of 20 MIN(-0006.0 Codelog Mode > 1)Config#1 > 6)Sensors 1) C 1) Class C): >-C[-6.0, 34.0]/50): 1)MIN 2)MAX 3)LEVEL SENSOR CLASS(0): (0-9)> MAX(+0034.0 C): >+ C LEVEL(050): (001-255)> MIN(+0000.0 PSI): >+ 2) psi 2) Type 6) Sensors SENSORS: 1)CLASS 2)TYPE 3)PARAM PSI[0.0, 50.0]/51): 1)MIN 2)MAX 3)LEVEL SENSOR TYPES(123): (1=C 2=PSI 3=ACT 4=EMG)> MAX(+0050.
of 20 Codelog Mode > 2)Scan 1) Continue to Log Data SCAN: I243 S100 14:22:33 148.220MHZ CH800 AMG=33 0)PAUSE SCAN 2)VIEW 3)SET DELTA 4)GPS 7)EN/DIS NOISE BLANK 8)INC. GAIN 9)DEC. GAIN 0) Pause Scan PAUSE: I243 S100 14:22:33 148.220MHZ CH800 AMG=33 0)RESUME SCAN 1)FILTERS 2)VIEW 3)SET DELTA 4)GPS 5)INC. FREQ 6)DEC.FREQ 7)EN/DIS NOISE BLANK 8)INC. GAIN 9)DEC. GAIN 1)Filters ...
of 20 Codelog Mode > 3)Master Ftable 3) Master FTable 1)UUC Freq UUC FREQ(150.000MHZ): (148-152.000)> 2) Master F Table 148.
of 20 SET Delta DELTA FREQ(001 KHZ): (001-999)> SET DELTA : 1)FREQ 2)GAIN DELTA GAIN(02): (01-99)> Revision D, #10055, March 16th, 2005
of 20 GPS Before GPS fix ... TEST GPS: TIME + POSITION After GPS fix ... TEST GPS: 15:34:27 (GMT) -44.0627687 79.4467891 Other possible message ...
of 20 Revision D, #10055, March 16th, 2005
