User's Manual

Aeronautical aluminum
by CNC Router
Power
Adapter
Charging Cabl
Connect the Type-c to the port in the side of the pad.
Connect the USB-A to the power adapter.
Plug the power adapter into an electrical socket.
The LED indicator turns red and lights up
for 3 seconds and then turns off.
Notice: Red light flashes when an error occurs.
Connect the USB end of the cable to the USB port on
your laptop.
The LED indicator turns red and lights up for 3 seconds
and then turns off.
Connect the USB end of the cable to the USB port
on your computer.
The LED indicator turns red and lights up for 3 seconds
and then turns off.
The LED indicator turns red and lights up for 3 seconds
and then turns off
The green breathing light works when charging, and the
green light is always on when fully charged.
Connect to Power Adapter Connect to Laptop for Charging Connect to Computer for Charging Charging Mode Applicable devices
Specification
LED indicator
LED indicato
r
LED indicator
1.Devices built-in with wireless charging receiver and
supports fast wireless charging
(IPhone 8 series/X series/11 series/12 series ;
Samsung S8/S9/S10/S20/Note8/Note10)
2.Device built-in with wireless charging receiver(not fast charge)
(Samsung S6、Nokia 850XL、MOTO 360 .,etc)
3.Devices with reserved wireless charging contacts, shall be
installed receiver coil
(Samsung S5、Note 4.,etc)
4.Devices shall be installed case with receiver
(iphone7/6s/6、iPhone7 plus/6s plus/6 plus.,etc)
Input Type C: DC 5V/2.0A ; 9V/2A ; 12V/1.5A
Output: 5W ; 7.5W ; 10W ; 15W
Transmission distance: ≤ 8mm
Charging efficiency: ≤ 80%
Size: 100.0 x 100.0 x 11 mm
Unit weight: ≈72g (NW)
Important Notes
Standard accessories
1. Do not disassemble, attempt to open,
or break the product
2. Keep away from fire and water
3. Do not use in a hot or humid environment to prevent
damage and potential harm to the user
4. Keep away from items with a magnetic strip or chip card
(credit cards, bank cards, etc.)
5. This item is not a toy; please keep away from children
6. Keep a distance of 20cm between the product and
implantable medical devices to avoid
potential interference
1. Wireless charger x 1 piece
2. USB-A to Type-C cable x 1 piece
3. User manual x 1 piece
LWC-F03
Metal Fast Wireless Charger
High strength aeronautical aluminum
User Manual
User Manual
Thank you for choosing our fast wireless charger
and enjoy the relentless pursuit of perfection!
Please read over and keep this manual for your records.
Pure copper coil
high-efficiency charging
FCC ID：2AYA9LWC-F03
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for
compliancecould void the user's authority to operate the equipment.
This device complies with Part15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
RF Exposure Warning Statements:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment shall be installed and operated with
minimum distance 20cm between the radiator & body.