Longshine Technologie Europe GmbH www.longshine.
FCC Certifications This Equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Table of Content Unpacking Information ..................................................................................1 1. Introduction to 24-port Fast Ethernet Web Smart Switch .......................2 1.1 General Description .............................................................................2 1.2 Key Features........................................................................................3 1.3 The Front Panel .............................................................................
Unpacking Information Thank you for purchasing the 24-port Fast Ethernet Web Smart Switch. Before you start, please check all the contents of this package. The product package should include the following: 1. One 24-port Fast Ethernet Web Smart Switch 2. One power cord 3. Rubber foot and screws 4. Rack-mount brackets 5. One RS-232 Cable (Optional) 6. One CD for user’s manual 7.
1. Introduction to 24-port Fast Ethernet Web Smart Switch 1.1 General Description The device is a 24-port 10/100Mbps Ethernet Web Smart Switch. Compare to the traditional 10/100Mbps Ethernet, the switch delivers a dedicated Fast Ethernet connection to every attached client with no congestion issue. The NWay auto-negotiation operation automatically negotiates with the connected partners on the network speed and duplex mode; that provides an easy way to integrate 10/100Mbps networks with no pain.
1.2 Key Features 24 fixed 10/100Mbps Fast Ethernet ports for easy network connecting application. Provide Auto-discovery Function for easy Network management. Provide 8K MAC address entries and 24 groups VLAN table Support up to 4 ports and 6 groups port aggregation. Supports 3 types of QoS priority for port base, 802.
Wiring for 10/100Mbps (Copper) Following are the summaries of cabling required: Media 10/100Mbps copper Speed Wiring 10Mbps Category 3,4,5 UTP/STP 100Mbps Category 5 UTP/STP LEDs Definition The rich diagnostic LEDs on the front panel can provide the operating status of individual port and whole system. Power LED This indicator lights green when the switch is receiving power; otherwise, it is off.
1.
2. Installing 24 Fast Ethernet Web Smart Switch This switch can be placed directly on your desktop, or mounted in a rack. Users can immediately use most of the features simply by attaching the cables and turning the power on. 2.1 Desktop Installation For desktop installation, the switch needs to put on a clean, flat desk or table close to a power outlet. Plug in all network cables and the power cord, then the system is ready. Before installing the switch, you must ensure: 1.
5. 6. 7. Repeat the two previous steps for the other side of the unit. Insert the unit into the 19" rack and secure with suitable screws (not provided). Reconnect all cables. 2.3 Installing Network Cables Station Connections Reference to the wiring statement of the previous section; connect each station to the switch with correct type of cables. Switch-to-Switch Connections In making a switch-to-switch connection, use every port to connect another switch or backbone is strongly recommended.
3. Management guide This section instructs you how to enter and set up the configurations, which can be accessed by RS-232 serial port (out-of-band) on the rear panel or by Telnet session / Internet Browser over the network (in-band). . Factory Default value: IP： Subnet Mask： Default Gateway： 192.168.1.1 255.255.255.0 192.168.1.254 3.
In-Band Connections (Web Browser / Telnet) To manage the switch through in-band access, you should configure the management station with an IP address and subnet mask compatible with your switch. 1. Running your Web Browser and enter the IP address “192.168.1.1” as the URL in the “address” field. 2. Key in the User name and password to pass the authentication. The factory default value of User Name and Password is “admin”. 3. After authentication procedure, the home page shows up.
3.2 Home Page On the Home page, you can select the configuration by clicking the menu tabs located on the upside of the UI. It includes, System Ports VLANS QoS Aggregation Discovery To restore the default Values of switch, Click the “Default” Button. If you want to reboot the switch, click the “Reboot” Button.
3.2.1 System To set up the system configurations such as login value, system name and IP address. Items Mac Address S/W Version H/W Version System name IP Address Subnet Mask Gateway Name Password Functions The Mac Address of the switch To check up the Software Version, see this.
3.2.2 Ports On the page, you can view the Port status, set up the Speed mode and enable the FDX flow control. Items Functions Admin Enable or Disable the Admin function Bandwidth To control the bandwidth, you can select the speed limitation you need in the drop list. (Disable/128K/256K/512K/1M/2M/4M/8Mbps) Operate mode Choose the Speed mode of port 10/100, Half/Full. If you set to auto speed, it will be auto-negotiation.
3.2.3 VLANS VLANS Configuration is for dividing the LAN into subnet groups for better network management. (total 24 VLAN groups) Mode: 1. Disable: Turn off the VLAN function by selecting the mode. 2. Port BASE: Group the port you select by entering the group number (Ex.1) in VLAN textbox and selecting the port numbers (Ex.1, 2,3,4) you want.
3.2.4 Aggregation/Trunking Configuration To set up the Port trunk groups, select “Enable” of the group you need. Don’t forget to click the “Apply” to save the setting. Supports 6 trunk groups for network application.
3.2.5 Qos There are three modes of Quality of Service to choose, TOS, Tag Base, and Port base. To Disable the QOS, click Disable and Click apply to save. To use the TOS, select TOS and click Apply to save. To enable the Tag Base, select Tag base and click Apply to save. When you enable Port Base, packets from the port you select will have higher priority. To enable the Port base, 1. Select the port-base 2.
3.2.6 Discovery When you install several 24port Fast Ethernet web-smart switches, the discovery management tool helps you to search and access those switches on the LAN easily. Therefore you can access any switch on your LAN without memorizing those IP addresses. You can only find switches with the IP Address compatible with the one you access. Note. The Maximum number of Address list is 16. Auto Search 1. Click the “Auto search” button to find the switches. 2.
3.2.7 Default To restore to default values, 1. Click the default button on the Howe page 2. Click “Yes” to enact. Don’t power off the switch while it’s work. 3.2.8 Reboot To reboot the switch, 1. Click the Reboot button on the Howe page 2. Click “Yes” to enact. Don’t power off the switch while it’s work.
4. Product Specifications Standard Interface Cable Connections Network Data Rate Transmission Mode LED indications Memory Emission Operating Temperature Operating Humidity Power Supply IEEE802.3 10BASE-T IEEE802.3u 100BASE-TX IEEE802.3x full-duplex operation and flow control IEEE802.
