Camera User Manual Version：22.1.2.
Statement Thank you for purchasing our product. If there are any questions or requests, please do not hesitate to contact the dealer. This manual applies to network camera and serves as a reference tool for your operating system. You can find information on how to implement the function in this manual, as well as a detailed menu. The photos, graphics, icons, etc. provided in the manual are for explanation and explanation purposes only, and may differ from the specific products.
WARNING Electrical safety regulations of the nation and the region must be strictly followed during installation or use. Please use the matched power adapter from standard company. Do not connect multiple IPCs with one single power adapter (Overload for adapter may lead to over-heat or fire hazard. Shut down the power while connecting or dismounting the device. Do not operate with power on. The device should be firmly fixed when installed onto the wall or beneath the ceiling.
Table of Contents CHAPTER 1 PRODUCT INTRODUCTION...........................................................................................................6 1.1 PRODUCT MANUAL..................................................................................................................................... 6 1.2 PRODUCT FEATURES.....................................................................................................................................6 CHAPTER 2 OPERATING INSTRUCTIONS..............
8.7 EVENTS................................................................................................................................................ 72 8.7.1 Ordinary Event...............................................................................................................................72 8.7.2 Smart Event................................................................................................................................... 86 8.8 BODY TEMPERATURE MEASURE........................
Chapter 1 Product Introduction 1.1 Product Manual Network camera is integrated video and audio acquisition, intelligent coding and network transmission and other functions of digital monitoring products. Using embedded operating system and high-performance hardware processing platform, with high stability and reliability to meet the diverse needs of the industry. Network camera based on Ethernet control, image compression can be achieved through the network and transmitted to different users.
With PTZ function camera support lens zoom, aperture control, PTZ control and cruise settings and other functions. Cloud storage function The network camera supports the cloud storage function, which can store the device's all-day recording on the cloud server and the motion detection alarm information on the cloud server. Body Temperature Measure Some network cameras support the body temperature measurement function.
Chapter 2 Operating instructions 2.1 Network Connection CAUTIONS If you have access to the Internet at your own risk, including but not limited to the product may be subject to network attacks, hacker attacks, virus infection, the company does not cause the product abnormalities, information disclosure and other issues, but the company will In time to provide you with product-related technical support.
Figure 2-3 2.2 Detecting and Changing the IP Address To access the IP address of a network camera, proceed as follows: Step 1: Search IPC IP address. Using the IP Search tool, you can search all the online cameras in the LAN and display the IP, MAC address, version, port and other information of the cameras, as shown in Figure2-4: Figure 2-4 Use the VMS client software to search for online devices. For details, refer to the VMS User Manual.
NOTE When setting the IP address of the IP camera, please keep the device IP address and the computer IP address in the same LAN segment. The default IP address is 192.168.1.168 and the port number is 80. The default administrator user name is "admin", and password is "admin". And you are highly recommended to "Modify" the initial password after your first login. To access the IPC of different subnets, set the gateway of the network camera after login. For details, see 7.3.1 Configuring TCP/IP. 2.
Please apply a dynamic IP from an ISP. With the dynamic IP address, you can connect the network camera to a modem or a router. The router is connected to the network camera Specific steps are as follows: Step 1： Connect the network camera to the router. Step 2： Assign a LAN IP address, the sub net mask and the gateway. For details, please refer to 7.3.1. Step 3：In the router, set the PPPoE user name, password and confirm the password. Step 4： Set port mapping, e.g., 80, 8000, and 554 ports.
Specific steps are as follows: Step 1: Install and run the IP Server software in a computer with a static IP. Step 2: Access the network camera through the LAN with a web browser or the client software. Step 3: Enable DDNS and select IP Server as the protocol type. For details, please refer to 7.3.2. Chapter 3 Access to the IPC by Client Software The VMS Lite client software is available on the company website (www.herospeed.net). You can use this software to view live video and manage IPC.
Chapter 4 Access to the IPC by Web Client 4.1 Preparation before install plugin In ensuring the IPC and the current user's computer after completion of all the hardware connection and power equipment normal, open the computer, run ping the IP address of the IPC (NOTE the IP address of the IPC in LAN must be unique). Such as IPC IP for 192.168.1.168, run ping 192.168.1.168.
Figure 4-2 Select system language (Simplified Chinese, Traditional Chinese, English, Russian, Korean, Polish, French, Japanese, Spanish, Portuguese, Italian, Hebrew, Turkish, Bulgarian, Arabic, German, Dutch, Czech, Vietnamese are supported), enter the username (default is "admin") and password (default is "admin"): click "login". NOTE If you have modified the IP address of the IP camera, please log in with the newly set IP address. 4.2.
Figure 4-4 To change your password, follow these steps: Step 1: Enter the old password and enter the new password in the Password and Confirm Password fields; Step 2: Set security questions 1, 2, and 3 and enter the answers. Step 3: Click "key export" to save the key file to your computer. Step 4: Click "Save" to complete the password modification. NOTE When setting a new password, you must set at least 8 digits and contain both letters and numbers to set it successfully.
modification interface. 4.2.3 Forget password When you forget your password, you can reset the password in two ways: security question verification and security key verification. Security question verification Step 1: On the login interface, click "Forget".
2 Figure 4-5 ○ 3 ). Step 4: Click "Re-login" to return to the login interface (as shown in Figure 4-5 ○ 3 Figure 4-5 ○ Security Key verification Step 1: On the login interface, click "Forget".
and click "Next". 2 Figure 4-6 ○ 3 ). Step 4: Click "Re-login" to return to the login interface (as shown in Figure 4-6 ○ 3 Figure 4-6 ○ NOTE When selecting "Security question validation", enter the correct answers to 2 questions to enter the "Set New Password" interface and proceed to the next step. When setting a new password, you must set at least 8 digits and contain both letters and numbers to set it successfully.
4.3 Install the LsIPCPlugin Controls NOTE When you use IE browser or 360 browser, you need to download and install the controls after login. The plugin of smart network camera is "LsIPCPlugin". Open Internet Explorer and log in to IPC to enter the preview interface, as shown in Figure 4-7.
1 Figure 4-8 ○ 2 Figure 4-3 ○ 20
3 Figure 4-3 ○ 4 Figure 4-3 ○ 21
5 Figure 4-3 ○ 6 Figure 4-3 ○ Notice 22
If the system prompt "installation failure", please uncheck the "cancel protection mode" in the setting safety of "Internet options" and enter the "custom level" ActiveX control Settings as show in Figure 4-4, and reinstall LsIPCPlugin after save settings. Figure 4-9 4.
preview, preview can also be achieved video, capture, electronic zoom and other functions. 【Playback】Select the time or video type to find the device TF card in the video and playback. 【Picture】Used to query, view and download image files stored in the network camera SD card. 【Configuration】 Click into the IPC configuration interface for system configuration and function configuration. 【PTZ Control】Used to set the PTZ preset point, cruise line and PTZ rotation direction preview real-time video and so on.
Chapter 5 Live preview 5.1 Live preview Click " " to enter the IPC preview interface, as shown in Figure 5-1: Figure 5-1 【switching window size】In the real-time preview interface on the top left of the preview ratio option, click "4: 3", "16: 9", "X1", "full screen" to switch the video preview scale. 【switching option】In the upper left of the real-time preview interface, there is a stream switching option. Click "Main Stream", "Sub Stream" and "Triple Stream" to switch preview video stream.
Manually capture the picture. Turn on / off the electronic zoom function, turn on the electronic zoom function, in the preview image, hold down the left mouse button to select the electronic zoom area, the interface shows the region to enlarge the image Turn on/off Sound. Open / Close talk back Table 5-1 5.2 Camera settings PTZ, zoom, cruise Click " " on the right side of the window to display the PTZ control interface.
Figure 5-3 The PTZ control interface operation buttons are shown in Table 5-2 below. 按 钮 说 明 Long press the arrow keys to control the horizontal and vertical direction, such as vertical rotation. (NOTE one of the bolt can only rotate horizontally, does not support vertical rotation). Click " ", the network camera will continue to rotate horizontally, then the button will turn red; then click once, then stop turning. "Zoom-" and "Zoom +".
Preset Click Preset to enter the Preset Settings menu and click the Presets icon to edit and recall the preset points. Select the preset number, click the " " button after the number, turn the preview channel image, make the image stay in a certain position; click " rotation; click " " button to call the preset point " button Clear the preset point. Cruise Click "Cruise" to enter the cruise settings menu, click the cruise icon area can be cruise editing and call.
Chapter 6 Playback In the main interface, click “ ”into the video playback interface. Playback interface can be stored in the camera SD card / TF card within the video file for query, playback and download operations. as show in Figure 6-1: Figure 6-1 Here you can according to the video type (ordinary video, alarm video) and video time to query SD / TF card in the video file, the query to the video file playback, screenshots, clips and download.
【Electronic zoom】During video playback, click " ", press and hold the mouse to select the area to be enlarged in the playback interface, release the mouse, the area is enlarged, click the right mouse button to restore the zoom, then the button becomes " ", click to close the electronic zoom. 【Capture】Video playback, click " " to capture the current playback screen image, the interface pops up the capture picture folder, which shows just captured the picture.
"Download" → "Save", set the download file storage path, the file starts to download, and wait for the download progress to complete. NOTE No SD card storage video camera and no video playback settings interface, please take the camera physical specific functions shall prevail. Before querying the video, please make sure that the SD card status in the device is "in use" and the 8.2.5 Rec Setup have been configured. Please refer to 8.
Chapter 7 Picture Click “ ” in the main interface to enter the Picture interface. The picture interface can query and download the picture files stored in the camera SD card, as shown in Figure 7-1. Figure 7-1 【Query】 Select the file type on the left side of the interface, set the image query time, and click ” ” to list the eligible image information in the list on the right. 【Download】 Check the image you want to view and click “Download” to save the image information to your local computer.
Chapter 8 Configuration Click “ ” in the main interface to enter the local configuration interface. Here you can set the device system, network, video, images, events and other parameters. 8.1 Local Configuration In the main interface, click "Configuration → Local Configuration" to enter the local configuration interface, where you can set the "Record File Settings", "Picture and Clip Settings", "Export param", "Import Param" storage path. Change the path by selecting Browse, as shown in Figure 8-1.
【Export parameter path】Set the storage path for IPC export parameters. 【Import param】Set device parameters in the computer's storage path, the file used to save the parameters of the web page egg device. 【Import parameter path】Set the storage path for the IPC import parameters. 8.2 System In the main interface, click "Configuration → System" to enter the system configuration interface. The system consists of system configuration, scheduled reboot, log query and security. 8.2.
Figure 8-3 【Time Zone】Displays the current device selection time zone. 【Time in Camera】Displays the current time of the device. 【NTP】The IPC time will synchronization with network, and you can change the different time zones. (This feature requires that IPC network environment can connect to the Internet.) Click on the "Save" after completing the settings. 【SNTP Sever】SNTP server address, including "time.windows.com", "time.nist, gov", "time-nw.nist.gov", "time-a.nist.gov", "time-b.nist.
Daylight saving time(DST) refers to the system of artificially stipulating local time for energy conservation. The unified time used during the implementation of this system is called “DST”. In the System Configuration interface, click "DST" to enter the daylight saving time setting interface, where you can enable daylight saving time, set daylight saving time, end time and end time, as shown in Figure 8-4.
program. (Please careful operation, the error of upgrade file will cause equipment system operate abnormally). 【Online Upgrade】To determine the device connected to the network, check the current version number, click on the "Check", such as the pop-up prompts the latest upgrade version, whether to download, click "OK", the device began to download the upgrade version to complete the automatic upgrade. Click "Cancel" to cancel the upgrade. 8.2.
Figure 8-7 【Search】 Set the date and start time of the log query, click "Search", the log list shows the IPC execution record that meets the conditions. 【Clear】Clicking clear button to empty all logging. 【Log export】Save the contents of the current log to the location you specified in txt format. 8.2.
Figure 8-8 1 ○ Add a User Step 1: Click “Add User” to add a user. Step 2: Input the User Name, select User Type and input Password. Step 3: Click “OK” to complete the user to add. Add User as shown in Figure 8-9.
Figure 8-9 CAUTIONS In order to improve the security of the product network, please change the password of the user name regularly. It is recommended to update the maintenance every 3 months. If the network camera is used in a high security risk environment, it is recommended to update once a month or every week. It is recommended that the system administrator manage the user effectively, remove the unrelated user and shut down the unnecessary network port.
3 ○ Modify the (admin user) password again Step 1: In the user list, click the “Edit” button after the admin user to enter the user interface. Step 2: Enter the old password, check “Modify Password”, and enter a new password in the Password and Confirm Password fields; Step 3: Click "Save" to complete the password modification. 4 ○ NOTE When the IPC password is the initial password “admin”, each time you log in, you will be prompted to change the password.
Step 1: In the main interface, click "Configuration → Storage → Plan configuration → 1 . Rec Setup" to enter the recording setting interface, as shown in Figure 8-10 ○ 1 Figure 8-10 ○ Step 2: To enable record, select the stream type (Main Stream, Sub Stream, Tri-Stream）、 video type（Normal Record, Motion Detection, Alarm, Motion detection and alarm).etc. Step 3: Set the recording schedule time period.
Tick "Select All" to enable 24/7 recording. Tick "Select all" to enable 24 hours of daily video recording throughout the week. . No SD card video recording function of the camera No SD card management interface, please take the camera physical specific functions shall prevail. When the video type selects motion detection, alarm, motion detection and alarm, the device will also perform scheduled recording while recording the selected recording type.
1 Figure 8-11 ○ Step 2: Set the screenshot schedule time period. - Method 1: Click the screenshot time period, manually fill in the start time and end time, set up and click Save. If you need to delete the time period, click the "Delete" button and then reset the time period. Method 2: Click the screenshot time period, two arrows will be displayed at both ends of the time period. Move the adjustment arrow left or right to adjust the arming time. Step 3: Repeat step 2 to set up a complete recording plan.
Step 5: Click "Snapshot parameters" to enter the snapshot parameters interface, as 2 . shown in Figure 8-11 ○ 2 Figure 8-11 ○ Step 6: Select options such as image format (JPEG), resolution, and picture quality as required, and set up timed snapshots and event snapshots. 【Image Format】Support JPEG format. 【Resolution】The captured image resolution. 【Picture quality】Three levels of "Basic Profile", "Main Profile" and "High Profile" can be selected.
NOTE The arming time of the event snapshot needs to be configured in each event. 8.3.
The steps to configure disk quota are as follows: Step 1: Select the memory card. Step 2: Set the disk quota, including parameters such as picture capacity and video capacity. Step 3: Click "Save". Step 4: Click "Format → OK" to complete the configuration of disk quota after formatting. 2 ○ Cloud Storage Cloud Storage Set up cloud storage. When the device triggers an alarm, you can store the alarm picture taken by the device on a cloud server.
obtain the "Verification Code". Step 4: Enter the verification code in the "Auth code" field of the cloud storage interface. Step 5: Click "Bind". 【Cloud Storage Type】Select the cloud storage type, Dropbox or Google in the drop-down menu. 【Web】Depending on the type of cloud storage selection play a cloud url, login web site registered account according to clew clouds. 【Auth Code】Login cloud web, the verification code will display on the cloud storage interface, than copy it in the space.
Step 2: Log in to IPEYE Client "http://182.18.195.252:8282", enter IPEYE login account & password, IPC user name & password, click “Confirm” to add the device, as shown in 3 . Figure 8-14 ○ 3 Figure 8-14 ○ Step 3: Log in to "https://www.ipeye.ru/" and enter the IPEYE device list to view the newly added device name as "cloud_xxxxx". Click "Play" to view the device real-time monitoring 4 . video.
Some cameras do not support the IPEYE function. The specific interface is subject to the actual product. 8.4 Network 8.4.1 Basic Setup 1 ○ TCP/IP The TCP/IP interface is used to view and configure network parameters such as the camera's IP address. You can enable DHCP or manually modify to configure the IPC network parameters.
port setting interface, where you can set the IPC network port and protocol port, the network port has HTTP port (default is 80), RTSP port (default is 554) , HTTPS port (default is 443), BITVISION port(default is 6000), the protocol port has the ONVIF port (default is 8999). As shown in Figure 8-16. Figure 8-16 【BITVISION Port】When the BitVision App is directly connected to the device, the "Private port" is entered into the BITVISION port.
DDNS After the DDNS (Dynamic Domain Name Server) parameter is set, when the IP address of the IPC changes frequently, the system can dynamically update the relationship between the domain name and the IP address on the DNS server. You can use the domain name to access the IPC directly without recording the constantly changing IP address.
【DDNS Type】Choose the type of Oray, NO-IP, Dyn, Planet Dynamic DNS and Planet Easy DDNS five types. 【Site Name】The input selection type corresponds to the successful domain name. 【DDNS User】The input selection type corresponds to the registered account. 【DDNS Password】The input selection type corresponds to the registration password. 【Confirm Password】Re-enter the password, this password and DDNS password. 【Status】Shows whether the current device is set up DDNS successfully.
upload FTP server image format JPEG. Step 3: Click "Save" to save the configuration. Step 4: Click "Test" to confirm whether the network connection and FTP configuration are correct. NOTE If the test fails, please recheck the network or FTP configuration. 【FTP Server】Fill in the FTP server address. 【Test】Enter the FTP server information and click "Test" to confirm the correctness of all input information and whether the device and server are connected properly. 【Port】Fill in the FTP server port number.
Figure 8-19 Step 2: Configure Sender, SMTP Server, Port, User Name, Password, and Receiver. Step 3: Click "Test" to confirm whether the network connection and SMTP configuration are correct. Step 4: Click "Save" to save the configuration. Sender 【Sender】Fill in the full address of the sender mailbox. 【SMTP Server】Fill in your email server address. 【Port】Fill in your email server port. 【Upload Via SMTP】In the drop-down menu, select SMTP file format, JPEG image format, AVI video and message for selection.
completion of the completion of the "Test" to ensure that all the correctness of the input information and network connectivity of the camera. P2P P2P is a private network penetration technology. It does not need to apply for a dynamic domain name, perform port mapping, or deploy a transit server. You can directly scan the QR code to download a mobile client. After registering an account, you can add and manage multiple IPC, NVR, XVR devices simultaneously on the mobile client.
App Client operation example The following content is introduced by taking the operation of the mobile phone client (BitVision App) as an example. The steps are as follows: Step 1: Use the Android or iOS phone to scan the corresponding QR code to download and install the BitVision App. Step 2: Run the client and log in to the account (No account is required to register first). Step 3: Add devices to the mobile client.
PPPoE(Point-to-Point Protocol over Ethernet) is one of the ways in which IPC devices access the network. After obtaining the PPPoE user name and password provided by the Internet Service Provider, you can establish a network connection through PPPoE dialup. After the connection is successful, the IPC automatically obtains a dynamic IP address of the WAN.
Figure 8-23 【Wireless Wifi Management】Wifi IPC can remember the accounts that have been connected to Wifi, and make the device connect or delete the Wifi account through wireless Wifi management. IPC Wifi configuration steps are as follows: Step 1: Click the "Scan" button to search for nearby WiFi hotspots; Step 2: Select to connect to WiFi, enter the WiFi password in the Key field; Step 3: Turn on "Enable DHCP" and click "Save".
Figure 8-24 The steps to turn on and set the camera wifi hotspot are as follows: Step 1: Select "access Point" in the Wireless Mode field; Step 2: Set the AP EssId, ApPsk, 80211nChannel, EssId Enabled switch, WpaMode, wireless IP, subnet mask, and wireless gateway address. Step 3: Click "Save" to complete the setup. 9 ○ NOTE Only cameras that support the wifi hotspot function have a WIFI hotspot interface. Please refer to the specific function of the camera.
Figure 8-25 NOTE Only PTZ-enabled cameras have a PTZ interface. Please refer to the actual camera function. 10 ○ SNMP Before setting SNMP parameters, the user needs to have an SNMP server, and ensure that the SNMP server is configured with relevant parameters and can work normally. IPC supports three simple network management protocol versions, V1, V2 and V3. The network management protocol is selected according to the SNMP server-side protocol version.
Figure 8-26 11 ○ RS485 In the main interface, click "Configure →Network → Advance Setup → RS485" to enter the RS485 configuration interface, as shown in Figure 8-27. By configuring the parameters of the RS485 serial port for interface configuration, please set the baud rate, data bit and other information of the interface according to the actual environment.
NOTE RS485 depends on the model, please refer to the actual equipment. 8.5 Video In the main interface, click "Configuration → Video" to enter the video and audio configuration interface, where you can set the device video, audio and other functions. 8.5.1 Video In the main interface click "configuration → video → video" into the video configuration interface, where you can set the IPC device name, stream type, encoding and other video parameters, as shown in Figure 8-28.
【Resolution】Switch the output resolution in the drop-down menu. 【Framerate】Set the frame rate of the current output video of the device. 【Bit Rate】Support 64-12000kbps. The higher the bit rates the better video quality, but it occupy the greater network bandwidth and the greater the pressure transmission. 【Rate Control】 Switch the code rate output mode in the drop-down menu, fixed rate and variable rate. 【I-Frame Interval】IPC acquisition key frame interval, can be set 1-5s.
Figure 8-29 【Audio Enable】Turn on / off device audio input. 【Audio Input】Select the audio input method. 【Audio Output】Select the audio output method. 【Audio Encode】Choose audio encoding, G711U/ G711A /AAC. 【Input Volume】Set the device input volume. 【Output Volume】Set the device output volume. 8.6 Image In the main interface, click "Configuration → Image" to enter the image configuration interface, where you can set the device image and OSD text and other information. 8.6.
Figure 8-30 【Image adjustment】You can input the value manually to set brightness, contrast, saturation, sharpness. These parameters shall be set according to the actual environment. The scope of valid values is from 0 to 255, you can drag the slider to set, and the default value is 128, as shown in Figure 8-31.
Figure 8-32 【Focus】 It is used to select the focus mode of the zoom camera. The default is "semi-autofocus", and "Automatic" focus and "Manual" focus can also be selected, as shown in Figure 8-33. Figure 8-33 【BackLight Settings】It is used to set backlight compensation and strong light suppression. The default is off, it can be turned on manually, and the backlight, strong light suppression intensity and dark area boost strength can be set, as shown in Figure 8-34.
1 Figure 8-35 ○ - When the fill mode is "Time", you can set the Dawn time and the Dark time (the start and 2 . end fill time) and the fill light brightness, as shown in Figure 8-35 ○ 2 Figure 8-35 ○ - When the fill mode is "Daytime", the device monitor video is lighted into a daytime effect. - When the fill mode is "Night", the device monitor video is added to the night effect.
Figure 8-36 Manual white balance: It is support Red, Green, Blue gain adjustable, adjust the range (0-255), set the click "Save". 【Video adjustment】Here you can turn on and set 2D or 3D digital noise reduction, as shown in Figure 8-37. Figure 8-37 【Image enhancement】Including flicker control, wide dynamic switch, HDR, as shown in Figure 8-38. Figure 8-38 Flicker control: The flash mode is selected according to the camera installation environment and the flicker standard.
strength, can be set to a value range of 0-255. 【Distortion】Used to set image distortion correction, as shown in Figure 8-40. Figure 8-40 Distortion mode: The default is Off. You can select On from the drop-down menu. Distortion intensity: The default is 128. When the distortion mode is on, the distortion correction strength can be set, and the value range can be set from 0-255. 【Image rotation】Used to set image mirroring and corridor pattern, as shown in Figure 8-41.
Figure 8-42 【Time】Turn on / off the preview interface time display. 【Text】Turn on / off the preview interface OSD text display. 【Show the week】Turn on/off the time display in the preview interface, you can choose "English" or "Chinese". 【Date Format】Set the preview interface to display the date format, default day / month / year, switchable month / day / year and year / month / day options.
Step 1: In the main interface click on the "Configuration → Events → Motion Detection" to enter the motion detection settings interface, as shown in Figure 8-43. Figure 8-43 Step 2: Click "Enable" or "Detect human movement only" to turn on the motion detection alarm. Step 3: Select the area to set the motion detection sensitivity, click "Save". 【Select All】Motion detection range to monitor all of the area, which Consists of 396(22*18) small squares.
detection. The default is to arm the alarm 24 hours a day. You can adjust the arming time as follows: - Method 1: Click the arming time period, manually fill in the start time and end time, set up and click "Save". If you need to delete the time period, click the "Delete" button and then reset the time period. - Method 2: Click the arming time period, two arrows will be displayed at both ends of the time period. Move the adjustment arrow left or right to adjust the arming time.
alarm information to the FTP server. 【Upload Via Cloud】Select and the system is configured with the cloud server, will send the alarm information to the cloud account. 【IO Output】Select and the IO output port is connected to the alarm device. During the alarm, the device will link the device to alarm. 【Flash Warning】After selection, the device will link the alarm light to flash at the selected time (day/night) when alarming.
setting. 3 ○ Video Tampering The occlusion alarm function is used to detect whether a monitoring area is blocked by human factors and other factors during a certain period of time. When the area of the device is blocked, the IPC will alarm according to the settings. When the occlusion alarm is generated, the occlusion alarm cause can be quickly discharged and the monitoring screen can be restored.
【Drawing Area】Move the mouse to the preview screen, click the left mouse button to select the range of motion detection, release the left mouse button, click “Stop Drawing” to complete the alarm area selection. 【Clear All】Clearing all the video tempering area that selected currently. 【Sensitivity】The default is 0, can switch the range of 0-2, the greater the value of the more sensitive equipment alarm. Step 4: Set the arming schedule.
NOTE When the arming time is set, there can be no overlap between any two time periods. Step 5: Set the linkage method. Alarm linkage methods include general linkage(Upload Via SMTP, Upload Via FTP, Upload Via Cloud, Flash Warning) and linkage alarm output(IO Output), as shown in Figure 8-49. Figure 8-49 【Upload Via SMTP】Select and the system is configured with SMTP, the alarm information will be sent to the SMTP recipient mailbox.
The default is 0 arming 24 hours a day. You can adjust the arming time as follows: - Method 1: Click the arming time period, manually fill in the start time and end time, set up and click "Save". If you need to delete the time period, click the "Delete" button and then reset the time period. - Method 2: Click the arming time period, two arrows will be displayed at both ends of the time period. Move the adjustment arrow left or right to adjust the arming time.
Figure 8-51 【Upload Via SMTP】Select and the system is configured with SMTP, the alarm information will be sent to the SMTP recipient mailbox. 【Upload Via FTP】Select and the system is configured with the FTP server, will send the alarm information to the FTP server. 【Upload Via Cloud】Select and the system is configured with the cloud server, will send the alarm information to the cloud account. 【IO Output】Select and the IO output port is connected to the alarm device.
- After the day of deployment time is set, if the other time also need to set the same arming time, click the right side of the timeline " " copy button, in the "copy to" interface check the "Select All" or a day, then Click "OK". Step 4: Click "Save" to complete the setting of the arming time. Figure 8-52 【Manual alarm】Manually control the alarm output device on the alarm output interface to link the alarm. 6 ○ Exception Set the alarm mode of abnormal events.
Figure 8-53 Step 2: Select the exception type and set the alarm output method. Step 3: Click on the “Save” after completing the settings. 【IO Output】Select and the IO output port is connected to the alarm device. During the alarm, the device will link the device to alarm. 【Flash Warning】After selection, the device will link the alarm light to flash at the selected time (day/night) when alarming.
Figure 8-54 Step 2: Set the lighting mode(Light always on, flicker), color(red, green, blue, cyan-blue, yellow, purple, white), and flashing time(The default is 5s, and the setting range is 1-60s). Step 3: Set the arming schedule. As shown in Figure 8-53. You can view, edit, and delete the arming time of the face recognition. The default is to arm the alarm 24 hours a day.
Figure 8-55 Step 2: Set the alert tone, alarm times(default 1 time, the adjustable range is 1-5 times) and volume (default 60, the adjustable range is 0-100). Step 3: Set the arming schedule. As shown in Figure 8-54. You can view, edit, and delete the arming time of the face recognition. The default is to arm the alarm 24 hours a day. You can adjust the arming time as follows: - Method 1: Click the arming time period, manually fill in the start time and end time, set up and click "Save".
9 ○ ROI ROI is the area of interest setting, users can set the most concerned and most interested area in the video screen through this function, IPC will improve the video image quality of the corresponding area when video encoding, reduce the encoding quality of other areas, so as to highlight The image effect in the selected area. The specific operation steps are as follows: Step 1: In the main interface, click "Configuration → Events → ROI" to enter the ROI setting interface, as shown in Figure 8-56.
NOTE The ROI function depends on the specific model, and the ROI function is only supported under the H.264 or H.265 code. Other codes do not support the ROI function at this time. The ROI configuration is more effective when using a non-ROI frame rate setting is lower. Click 【Delete】 in the corresponding setting area to delete the corresponding ROI area. 8.7.
8-58. Figure 8-58 Step 2: Check "Enable" to enable intrusion detection. Step 3: Select "Warn Region": The system supports setting up to 4 warn region. After selecting a warn region, you need to make the following settings. After setting, please click "Save". 【Drawing Area】Click “Drawing Area”, move the mouse to the preview screen, click the left mouse button and draw the endpoint of the quadrilateral guard area, then click the preview interface to complete the area drawing.
up and click "Save". If you need to delete the time period, click the "Delete" button and then reset the time period. - Method 2: Click the time of deployment, the time period will display two circles at both ends, the mouse moves to the circle, and move the adjustment arrow left and right to adjust the arming time. - You can set up more than one time period for up to 8 time periods.
result. The specific operation steps are as follows: Step 1: In the main interface click on the "Configuration → Events → Smart Event → Line Cross Detection" to enter the Line Cross Detection settings interface, as shown in Figure 8-60. Figure 8-60 Step 2: Check "Enable" to enable intrusion detection. Step 3: Select "Warn Line": The system supports setting up to 4 warn line. After selecting a warn line, you need to make the following settings. After setting, please click "Save" below.
the progress bar or enter the value directly in the value box to modify the sensitivity. The greater the sensitivity, the easier it is to trigger an alarm. Step 4: When you need to set other Warn Line, repeat step 3 to complete the setup. Step 5: Set the arming schedule. As shown in Figure 8-61. You can view, edit, and delete the arming time of the Line Cross detection. The default is to arm the alarm 24 hours a day.
【Linkage Method】refers to the response made by the device when an alarm event occurs. The linkage includes "General Linkage", "Upload Via SMTP" and "Upload Via FTP". 4 ○ Loiter Detection The loiter detection function is used to detect that the target stays within the set area for more than the set time threshold, and then alarms according to the judgment result.
movement in the detection area. The larger the time threshold, the longer the target continues to move in the detection area to trigger an alarm. 【Sensitivity】Used to set the sensitivity of detected area intrusion. The default is 50. Drag the progress bar or enter the value directly in the value box to modify the sensitivity. The greater the sensitivity, the easier it is to trigger an alarm. Step 4: When you need to set other Warn Region, repeat step 3 to complete the setup. Step 5: Set the arming schedule.
When the arming time is set, there can be no overlap between any two time periods. Step 6: Set the linkage method as needed. 【Linkage Method】refers to the response made by the device when an alarm event occurs. The linkage includes "General Linkage", "Upload Via SMTP" and "Upload Via FTP".
preview interface to complete the area drawing. 【Clear All】Used to delete the selected alert area. 【Proportion】Indicates the proportion of personnel in the entire alert area. When the proportion of personnel exceeds the set percentage, the system will generate an alarm. The percentage is 50% by default. The larger the value, the more people can be accommodated in the alert area, and the less likely it is to trigger an alarm.
NOTE When the arming time is set, there can be no overlap between any two time periods. Step 6: Set the linkage method as needed. 【Linkage Method】refers to the response made by the device when an alarm event occurs. The linkage includes "General Linkage", "Upload Via SMTP" and "Upload Via FTP". 8.8 Body Temperature Measure 8.8.
【Temperature measurement alarm threshold】The device triggers an alarm temperature value. When the temperature recognized by the device exceeds this value, the device alarms. 【Temperature measurement information display position】The position of temperature-related information displayed on the device screen (Upper left corner, Lower left corner, Upper right corner, Lower right corner).
Chapter 9 Frequently Asked Questions 1.Why can not access the camera by IE? Answer: There maybe 4 reasons, Details are as follows: a.The network unreasonable? Solution: First you can connect network by PC, check the network cable if it is good. And check the network between the camera and the PC is good. b.The IP address of the camera is occupied by other device or PC? Solution: You can connect the camera with your PC directly, and modify the IP address or use the IP search tool. c.
FCC Caution This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
