Guardian Aler DEALER SET-UP & PROGRAMMING INSTRUCTIONS Model # 40911 v3.
THESE INSTRUCTIONS ARE FOR THE DEALER. REFER TO THE “QUICK START GUIDE” FOR BASIC INSTALLATION. These instructions are for the Dealer to set-up and program the CaretakerSentry System to operate with the Central Station of your choice. The CaretakerSentry product (the “System”) uses the industry standard “Contact ID” and “4+2” protocols. Voice prompts provide easy set-up and testing. Basic set-up requires you to: • Install the 4 AA rechargeable Ni-MH batteries in the Base unit.
TABLE OF CONTENTS System Components..........................................................................4 Limitation of Liability...........................................................................5 Installing the Batteries.......................................................................6 Connecting the Base Unit...................................................................6 Power Connection...............................................................................
System Components: The items below are included with your System . Base Unit Part #40914 Pendant Part #40915 AC Adapter Rechargeable AA Batteries - 4 Pieces Part #35918 Phone Cord Lanyard 4 Wrist strap CaretakerSentry® v3.
Limitation of Liability This page is a summary of the Disclaimer and Limited Warranty disclosed in full at the end of this instruction manual. Read these carefully. The purchaser agrees by using this CaretakerAlert (the “System”) to the terms and conditions below and in the Disclaimer and Limited Warranty. The purchaser also agrees to read and follow all instructions and warnings on the product and contained within these Installation and Operation Instructions.
Installing the Batteries: Base - larger batteries: The Base unit requires 4 rechargeable 2400 mAH NiMH batteries (included). They will provide you with up 24 hours of battery back- up protection in the event of a power failure. They will not be damaged by continually charging in the base unit. The ratings on these can be 2400 mAh or higher.
Telephone Connection: A standard telephone line is required to use your System. Your phone will work with your existing touch-tone phone line and existing service. It works the same way as any cordless phone. NOTE: Touch Tone service is required. Simply plug one end of the telephone cord into a telephone jack, and the other end into the “Line In” jack at the back of the Base unit. Note - you will feel a ‘click’ when the cords are firmly seated in the wall and the Base unit jack receptacles.
Dealer Programming Instructions: The System has several features to help with the programming. The System uses voice prompts and LED lights to guide you through the process. They give you a good audible confirmation of the progress as you are programming. Second are the LED lights on the base unit and the Pendant.
Note: If you don’t have an open line when you begin to program the System with your telephone - the phone company will think you are trying to dial an outside number and will try to complete the call. By having the phone line already in use with your cell phone or other called party - you are now ready to program the System. Step 3: With the phone connection established in Step 2, slide the slide switch at the back of the Base unit to Programming Mode. You will hear an audible announcement of this position.
4. Slide Programming Switch to Normal Operation [Voice prompt – “Emergency Call Mode”] Note: there is no way to easily reset the passcode if the number is forgotten or mis-programmed, the unit will have to be exchanged. A forgotten passcode IS NOT a warranty issue. Be careful when changing passcodes. Setting Programming Options: As always - First establish a phone line as you did in Step 2 on page 8.
[Voice prompt 2 – Spanish] [Voice prompt 3 – French] 4. Enter “#” (to exit programming mode) [Voice prompt –Programming complete] 5. Slide Programming Switch to “Normal Operation” Option #1 – Dial 9 Before Number - Dials ‘9’ to get an outside line. 1. Enter (Passcode) – XXXX then “**” (Default is 1234) [Voice prompt – Option Mode] 2. Enter – 1 [Voice prompt – Dial 9 before number, 1 for YES – 3 for NO] 3. Enter either 1 or 3 [Voice prompt 1 – YES] [Voice prompt 3 – NO] – FACTORY SETTING 4.
DLE-200 test box. NEVER LEAVE THE UNIT IN THIS MODE FOR NORMAL OPERATION. 1. Enter (Passcode) – XXXX then “**” (Default is 1234) [Voice prompt – Option Mode] 2. Enter – 4 [Voice prompt – DEMO Tradeshow Mode], 1 for YES 3 for NO– FACTORY SETTING 3. Enter either 1 or 3 [Voice prompt 1 – YES] [Voice prompt 3 – NO] 4. Enter “#” (to exit programming mode) [Voice prompt – Programming complete] 5.
[Voice prompt – Periodic test interval, 1 for 1 day, 2 for 7 days, FACTORY SETTING 3 for 30 days] 3. Enter 1, 2 or 3 [Voice prompt 1 – Every day] [Voice prompt 2 – Every 7 days] [Voice prompt 3 – Every 30 days] 4. Enter “#” (to exit programming mode) [Voice prompt – Programming complete] 5. Slide Programming Switch to “Normal Operation” [Voice prompt – “Emergency Call Mode”] Option #9 – Reset To Factory Settings 1. Enter (Passcode) – XXXX then “**” (Default is 1234) [Voice prompt – Option Mode] 2.
7. If no passcode or an incorrect passcode is entered within 15 seconds, the CaretakerSentry unit will hang up and reset. 8. The dealer will press ‘9’ to end programming, exit and reset the CaretakerSentry unit. Note: The programming voice prompts will still be heard from the base while the unit is being remotely programmed – this is designed to allow the customer know that changes are being made to their unit.
Erasing All Previously Learned Pendants: Simply holding down the RED Code Learn button at the back of the Base unit for 8 seconds. You will hear the confirmation of “Erase All Pendants, All pendants Erased” from the Base unit. After that, you can program a new pendant to the base unit following the steps above as desired. Basic Set-up and Test: Lanyard, Wrist Strap The System comes with 2 accessories for carrying the pendant. You can wear the Pendant using the Lanyard or Wrist-strap.
The Base also counts these 13 hour checks. If 4 reports are missed in a row (52 hours later), the Base unit will send a loss of RF signal to the central station. This System Check feature is very useful - allowing you to confirm that the System has coverage from all parts of the home. Put the base into the test mode and simply walk to the various parts of your home and push the Gray Emergency button until you hear “Battery is OK” voice prompt.
TROUBLESHOOTING GUIDE: What if I can’t get the System to work? Step 1 – Push the Black RESET button with a pen at the back of the Base unit (next to the power cord). Check the System. If it is now working skip the remaining steps. Step 2 – Check the PENDANT.
Central Station Items of Interest: Number of call attempts: 9 times - alternating between the first and second numbers programmed. Supervision of Pendants Yes – all pendants check in with the Base every 13 hours. A Pendant missing for more than 52 hours signals a “Loss of RF” condition/report. Reporting of Low Pendant Battery to Central Station Upon receipt of first “Replace Battery Now” Reporting of AC Power Loss After8hours of power loss - and only once.
Information The FCC Wants You To Know: Caretaker Sentry Base Unit - Model 40914 FCC ID: TYD-CS40914 IC ID: IC: 8471A-CS40914 Caretaker Sentry Standard Pendant - Model 40915 FCC ID: TYD-CS40915 IC ID: IC: 8471A-CS40915 Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules.
General Warnings And Precautions! Warning! - LogicMark, LLC DOES NOT represent this unit to be waterproof. To reduce the risk of damage to the unit, DO NOT expose the pendant or base unit to prolonged water, rain or moisture. - This System is intended for residential use only. It may not work properly if connected to some commercial phone Systems. - This System works with tone dialing Systems only. Do not use if you have pulse dialing only.
PURCHASER’S EXCLUSIVE REMEDY: Purchaser’s exclusive remedy for LogicMark LLC’s default hereunder is to require LogicMark LLC to repair or replace, at LogicMark LLC’s option, any equipment or part of the personal emergency alert System which is non-operational during LogicMark LLC’s warranty period. LIMITATION OF LIABILITY: This equipment is not designed or guaranteed to prevent any loss or injury.
Replacement Parts / Optional Accessories All prices are shown are MSRP and are in US Dollars Lock Box Part #30913 $34.95 Rechargeable AA Batteries 4 Pieces Part #35918 $15.95 Extra Pendants Part #40915 22 CaretakerSentry® v3.
Product Specifications: RF Characteristics: Communication Protocols 433 MHz – 1 way pendant Switchable Duplex or Simplex voice communication through base. Two options: Ademco Contact ID / 4+2 Operating Range Covers your typical American house and into the front, back, and side yards. Up to 600 feet line-of-sight from Base unit. Power Adapter Ratings Input: 110 VAC Output: 7.
10106 Bluegrass Pkwy Louisville KY, 40299 Tel: 1-502-410-0402 Toll Free: 1-888-283-6516 Fax: 1-703-934-7935 www.LogicMark.com ©2013 LogicMark, LLC 24 CaretakerSentry® v3.
