Intelligent Electronic swing handle – User operations guide Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. We are not liable for any injury or loss that results from the use of this equipment. For Sales and support please email sales@logicalinfrastructure.
Intelligent Electronic swing handle – User operations guide Logical Infrastructure (LI) Intelligent Electronic Handle (i-Handle) is an IT Cabinet level security access control swing handle solution with built in multi card reader, environmental sensors, integrated door lock position and magnetic door contact sensors. . Designed for easy installation with minimal cabling and without the need for dedicated structured cabling infrastructure.
Intelligent Electronic swing handle – User operations guide MOTOR MODEL ELECTRICAL SPECIFICATION: -POWER 4.5V TO 5V - OPERATON CURRENT: LESS THAN 500mA AT 5V DC WITH NO EXTERNAL MECHANICAL LOAD APPLIED TO HANDLE. - MAX CURENT WITH STALLED ACTUATOR: 1A AT 5V DC. - STANDBY CURRENT: 300mA, TYPICAL.
Intelligent Electronic swing handle – User operations guide FCC/IC COMPLIANCE / TM / WARRANTY To satisfy FCC&IC RF exposure requirements, a separation distance of 20cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. Les antennes installées doivent être situées de facon à ce que la population ne puisse y être exposée à une distance de moin de 20 cm.
Intelligent Electronic swing handle – User operations guide • Safety Instructions • Please refer to the below instructions before using the Ihandle. Save this manual for future reference. • • • • ■ If cleaning The Ihandle is required. Don’t use liquid or spray detergent; use a moist cloth. ■ Install and operate the Ihandle Preferably, in an air-conditioned environment with temperatures not exceeding 60º Celsius (140º Fahrenheit).
Intelligent Electronic swing handle – User operations guide Standard supplied Inventory * can be modified to suit specific requirements Optional extras.
Intelligent Electronic swing handle – User operations guide 2m iHandle Comms Cable 4 pin JST to RJ45 (2) i-Handle QTY (2) 1.2m door switch sensor kit QTY (2) (Switch sensor + Magnet + 1.2m cable to 5pin connector) Blue Network Cable 2.5m (1) - From front door Red Network Cable 2.
Intelligent Electronic swing handle – User operations guide Installation: Check the cut-out dimensions. For retrofit, remove the existing rack handles and check the cut-out dimensions (see picture below for typical front door and rear door). Keep the cam from the existing handles (used in Step 4). Note: The LI Electronic i-Handle can be retrofitted on racks subject to the door having a cut-out dimensions 125mmx50mm.
Intelligent Electronic swing handle – User operations guide 1. Typical door Typical door 2. Push the i-Handle through the cut-out in the door.
Intelligent Electronic swing handle – User operations guide 3. Put the metal back cover on the inside of the handle and insert the 3 screws to secure the handle in place, alternate between the screws while tightening to prevent skewing of the handle. 4. Place the door cam over the handle spindle and then a thick or thin door limiter using the spring screw to secure the mechanism. (For retrofit, re-use the front and rear door cam). Check the cam closes snuggly when the handle is rotated.
Intelligent Electronic swing handle – User operations guide Network connection: Front Door 1. Connect the i-Handle Comms Cable 4 pin to RJ45 150mm cable to the iHandle and attach the Blue Network Cable to the RJ45 connector. 2. Connect the RJ45 coupler and Blue Network Extension Cable to the Blue Network Cable. 3. Route and fix the network cable using cable ties and adhesive pads. Ensure the network cable has slack on the hinge side of the door so that it does not get pinched.
Intelligent Electronic swing handle – User operations guide Door Switch Sensor 1. The Door Switch Sensor consists of two parts: ● 1.2m cable to 5pin connector with Door switch sensor ● Magnet 2. Plug the 5pin connector into the back of the i-Handle. 3. Route and attach the 1.2m cable to the inside of the door and attach the switch sensor to the door using a dual adhesive pad or screws. In most instances the best location is near the top of the door on the handle side. 4.
Intelligent Electronic swing handle – User operations guide Environmental Sensors: 1. The i-Handle has an internal temperature and humidity sensor. 2. One additional environmental sensor (not supplied in the i-Handle kit) can be attached to the spare port on the i-Handle. Configuration: 1. The front door of a rack is referred to as the “cold aisle” and the rear door as the “hot aisle”. 2.
Intelligent Electronic swing handle – User operations guide LED light status: LATCH & LED colour STATUS definitions SECURED SOLID GREEN ELECTRONICALLY RELEASED BLINKING GREEN UNAUTHORISED CARD SWIPE BLINKING MECHANICALLY RELEASED WITH KEY BLINKING RED ELECTRONICALLY LOCKED/SWINGHANDLE OPEN BLINKING /RED DOOR CONTACT OPEN FOR 5 MINUTES BLINKING RED/BLUE FAULT DETECTED SOLID RED 14
Intelligent Electronic swing handle – User operations guide FAQ: What if the Ihandle fails how do I access my IT cabinet? Use the override key provide to manually open the swinghandle.
