Logical Intelligent Electronic swing handle +POE Bridge SBIP01 – User operations guide Infrastructure Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. We are not liable for any injury or loss that results from the use of this equipment. For Sales and support please email sales@logicalinfrastructure.
Logical Intelligent Electronic swing handle +POE Bridge SBIP01 – User operations guide Infrastructure Logical Infrastructure (LI) Intelligent Electronic Handle (i-Handle) is an IT Cabinet level security access control swing handle solution with built in multi card reader, environmental sensors, integrated door lock position and magnetic door contact sensors. The LI POE bridge allows the I-Handles to communicate and be powered via a standard POE switch. .
Logical Intelligent Electronic swing handle +POE Bridge SBIP01 – User operations guide Infrastructure MOTOR MODEL ELECTRICAL SPECIFICATION: -POWER 4.5V TO 5V - OPERATON CURRENT: LESS THAN 500mA AT 5V DC WITH NO EXTERNAL MECHANICAL LOAD APPLIED TO HANDLE. - MAX CURENT WITH STALLED ACTUATOR: 1A AT 5V DC. - STANDBY CURRENT: 300mA, TYPICAL.
Logical Intelligent Electronic swing handle +POE Bridge SBIP01 – User operations guide Infrastructure To satisfy FCC&IC RF exposure requirements, a separation distance of 20cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. Les antennes installées doivent être situées de facon à ce que la population ne puisse y être exposée à une distance de moin de 20 cm.
Logical Intelligent Electronic swing handle +POE Bridge SBIP01 – User operations guide Infrastructure • ■ If cleaning The Ihandle is required. Don’t use liquid or spray detergent; use a moist cloth. • • • • • • • ■ Install and operate the Ihandle Preferably, in an air-conditioned environment with temperatures not exceeding 60º Celsius (140º Fahrenheit).
Logical Intelligent Electronic swing handle +POE Bridge SBIP01 – User operations guide Infrastructure Optional extras. Door cams Multi latching rod system gearbox i-Handle Kit: The i-Handle Kit comprises the following: Quantity 2pcs Quantity 2pcs Quantity 2pcs Quantity 1pcs Quantity 1pcs Quantity 2pcs Quantity 2pcs Quantity 2pcs Quantity 2pcs Quantity 4pcs Quantity 1pcs Intelligent swinghandle 2m communications cable female rj45 to 4pin JST connector 1.
Logical Intelligent Electronic swing handle +POE Bridge SBIP01 – User operations guide Infrastructure 2m iHandle Comms Cable 4 pin JST to RJ45 (2) i-Handle QTY (2) 1.2m door switch sensor kit QTY (2) (Switch sensor + Magnet + 1.2m cable to 5pin connector) Blue Network Cable 2.5m (1) - From front door Red Network Cable 2.
Logical Intelligent Electronic swing handle +POE Bridge SBIP01 – User operations guide Infrastructure Metal bracket back cover (2) fixing screw (3) Cable Protect Cover (2) Thin Rotation limiter (2) Spring screw (2) Key (4) Installation: Check the cut-out dimensions. For retrofit, remove the existing rack handles and check the cut-out dimensions (see picture below for typical front door and rear door). Keep the cam from the existing handles (used in Step 4).
Logical Intelligent Electronic swing handle +POE Bridge SBIP01 – User operations guide Infrastructure 1.
Logical Intelligent Electronic swing handle +POE Bridge SBIP01 – User operations guide Infrastructure Typical door Typical door 2. Push the i-Handle through the cut-out in the door. 3. Put the metal back cover on the inside of the handle and insert the 3 screws to secure the handle in place, alternate between the screws while tightening to prevent skewing of the handle.
Logical Intelligent Electronic swing handle +POE Bridge SBIP01 – User operations guide Infrastructure 4. Place the door cam over the handle spindle and then a thick or thin door limiter using the spring screw to secure the mechanism. (For retrofit, re-use the front and rear door cam). Check the cam closes snuggly when the handle is rotated. Swap the door limiters or slightly bend the cam if the cam hits the rack frame. 5. Repeat the procedure for the second door.
Logical Intelligent Electronic swing handle +POE Bridge SBIP01 – User operations guide Infrastructure 1. The Ideal installation position for the POE bridge is towards the Front of the IT cabinet within the side of the cabinet either top of bottom depending on how the Ihandle network cables are routed through the doors. 2. The POE Bridge has multiply fixing points allowing for flexible installation.
Logical Intelligent Electronic swing handle +POE Bridge SBIP01 – User operations guide Infrastructure Network connection: Front Door 1. Connect the i-Handle Comms Cable 4 pin to RJ45 150mm cable to the iHandle and attach the Blue Network Cable to the RJ45 connector. 2. Connect the RJ45 coupler and Blue Network Extension Cable to the Blue Network Cable. 3. Route and fix the network cable using cable ties and adhesive pads.
Logical Intelligent Electronic swing handle +POE Bridge SBIP01 – User operations guide Infrastructure Door Switch Sensor 1. The Door Switch Sensor consists of two parts: ● 1.2m cable to 5pin connector with Door switch sensor ● Magnet 2. Plug the 5pin connector into the back of the i-Handle. 3. Route and attach the 1.2m cable to the inside of the door and attach the switch sensor to the door using a dual adhesive pad or screws.
Logical Intelligent Electronic swing handle +POE Bridge SBIP01 – User operations guide Infrastructure 1. The i-Handle has an internal temperature and humidity sensor. 2. One additional environmental sensor (not supplied in the i-Handle kit) can be attached to the spare port on the i-Handle. Configuration: 1. The front door of a rack is referred to as the “cold aisle” and the rear door as the “hot aisle”. 2.
Logical Intelligent Electronic swing handle +POE Bridge SBIP01 – User operations guide Infrastructure LED light status: LATCH & LED colour STATUS definitions SECURED SOLID GREEN ELECTRONICALLY RELEASED BLINKING GREEN UNAUTHORISED CARD SWIPE BLINKING MECHANICALLY RELEASED WITH KEY BLINKING RED ELECTRONICALLY LOCKED/SWINGHANDLE OPEN BLINKING /RED DOOR CONTACT OPEN FOR 5 MINUTES BLINKING RED/BLUE ERROR DETECTED SOLID RED 16
Logical Intelligent Electronic swing handle +POE Bridge SBIP01 – User operations guide Infrastructure FAQ: What if the Ihandle fails how do I access my IT cabinet? Use the override key provide to manually open the swinghandle.