User's Manual

ManualsBrandsLodar ManualsElectronicsTransmitter Standard-433

Table Of Contents

or Disconnect Battery

IDENTIFY POWER

CONNECTION POINT

AND ISOLATE SUPPLY

Fuse

Remove fuse

Vehicle batteries contain gasses

which are flammable and explosive.

Wear eye protection and do not lean

over battery while disconnecting. Do

WARNING

1. The Receiver is designed to carry a maximum of 15 Amps. That is, for example,15 Amps

through one output or 5 Amps each through 3 outputs.

2. Master Output. This can be configured to Continuous or Parallel operation, see overleaf for

details.

3. If Receiver outputs are connected in parallel with an external switching device (wired remote)

the Receiver will instantly switch off when the wired remote is operated

4. Lodar Receivers have an isolation switch for safety, to allow for registering a MUST

replacement Transmitter.

5. Safety Feature. Both the Transmitter and the Receiver will “time out” after 30 minutes of

inactivity. This can be altered, ask your dealer.

BEFORE YOU START

Wiring Instructions for 2 & 4 Function, 92 & 93 Series, FET Receivers.

92 02/4 RX

& 93 02/4 RX

have

7 core cable

CONNECT

WIRES

Transmitter

Function

Convention

92 00 RX

& 93 00 RX

have

4 core cable

www.lodar.com

9000

F1 F2

or re-connect Battery

ACTIVATE THE

RECEIVER SUPPLY

Fuse

Replace fuse

Press the Transmitter buttonRESET

to activate the system, and carefully

test each function for correct operation.

TEST

CONNECT TRANSMITTER BATTERY

Batteries generally have to be

disconnected when shipping.

Secure using 5mm (3/16") bolts (not supplied)

through the 4 mounting feet

TAKE TIME TO LOCATE THE BEST POSITION

If necessary, power the Receiver and move it around

the vehicle until the required performance is achieved.

Operate the Transmitter and observe the Receiver

internal LED’s.

Mount as HIGH as possible

AVOID surfaces with HEAVY VIBRATION

AVOID DIRECT SPRAY from wheels

In a HOT CLIMATE fit in a SHADED position

Cable gland should face DOWN or BACK

Receiver 92 04 RX and 93 04 RX shown,

Waterproof to IP67, complete with 3 metres (10 ft) cables

CAUTION

MOUNT RECEIVER

STOP

POSITIVE

NEGATIVE

12/24 Volts DC Nominal

Positive Supply

RED

Negative

BLACK

GREEN

YELLOW

BROWN

BLUE

WHITE

Output Function 1

Output Function 2

Output Function 3

Output Function 4

Output Function Master

Wire used for

Wire Colour

Not Present

Not Used

9200RX

and 9300RX

9202RX

and 9302RX

9204RX

and 9304RX

Make notes about the

connections made

in the boxes below

What is the MASTER Output for ?

It is used to operate the pump of an electro-hydraulic

power pack or maybe a clutch pump. It can also be

used for powering a dump valve, master valve etc.

It can be configured to work continuously, that is ON

when SET is pressed and OFF when STOP is

pressed; or in parallel with any output, that is, it is

active only a function is operated. If it is needed with

certain functions only, this can easily be configured.

92104.

05 FET 24

Summary of content (2 pages)

PAGE 1
Wiring Instructions for 2 & 4 Function, 92 & 93 Series, FET Receivers. 1 ! 1. 2 IDENTIFY POWER CONNECTION POINT AND ISOLATE SUPPLY BEFORE YOU START The Receiver is designed to carry a maximum of 15 Amps. That is, for example,15 Amps through one output or 5 Amps each through 3 outputs. Fuse 2. Master Output. This can be configured to Continuous or Parallel operation, see overleaf for details. 3.
PAGE 2
LED marked “SET” Component Detail LED’s marked “F1 - F2 - F3 - F4 and M” When ON indicate an output to that function Indicates system is active LED marked “FAULT” Indicates an overload is present; the System cannot be RESET until overload is removed. This LED blinks for 20 seconds when the Receiver is initially powered. A replacement Transmitter has to be registered during this 20 second period.