R REV ERP PL3542Q-GL-SMT00030A-V2 80G 0.1 ERP P/N: PL3542Q/PGI302 STM000,REV.A UMPGL302FC20220214 110x170mm, , ,12 42 ROHS2.0,REACH,POPs,PAHS,PROP65, K FOR COMMERCIAL USE & PROFESSIONAL INSTALLATION WWW.LOCKLYPRO.
Table of Contents Section 1 - Product Highlights 1.1 Product Features Section 2 - Product Overview 2.1 Product Overview 2.2 Wiring Diagram 2.3 Installation Diagram 2.4 Understanding Your New Lock 2.5 Pair Lock with the Lockly Pro App 2.6 Rebooting Your Lock 2.7 Keypad Display Switch 4.4 Unlocking /Locking with App 4.5 Safe Mode 4.6 Disabling Safe Mode 4.7 Rain Mode 4.8 Welcome Mode Section 5- Video Doorbell 5.1 Video Doorbell Section 6 - Advanced Features 6.
1.1 Product Features Video Monitoring and Recording (PGI303) Full HD video camera streaming directly to your smartphone in real-time, gives a head to toe 130° view angle of who's at your front door. Video recordings are stored locally with no monthly fees. Patented Hack-Proof PIN Genie Keypad Digits are randomly displayed on the keypad ensuring access codes to be undetectable to intruders after repeated use. Numbers are randomly distributed across 4 buttons, with 3 numbers in each button.
2.1 Product Overview - PGI302 Touchscreen Keypad Screen Lock Icon Cable/Wire Outlet CARD Anti-Theft Alarm RFID Card Reader Fingerprint LED Indicator Doorbell 1 2 3 4 5 6 7 8 Wiring Reset Button Program Button 1 PUSH Lock Control Port 2 LOCKLY NC Door Open Detection Port 3 BUTTON-SW To ensure the device works properly, please make sure the wires are connected according to this diagram.
2.1 Product Overview - PGI303 Full HD video Camera Touchscreen Keypad Screen Lock Icon Cable/Wire Outlet RFID Card Reader Anti-Theft Alarm Fingerprint Speaker Port LED Indicator CARD Doorbell 1 2 3 4 5 6 7 8 Wiring Reset Button Program Button To ensure the device works properly, please make sure the wires are connected according to this diagram.
2.2 Wiring Diagram 1 2 3 Access Control Power Supply AC100-240 NO OR NC +12V V+ GND V- PUSH GND NO PUSH 12V COM LOCK NC NC Electromagnetic Lock A V+ V- Wireless Transceiver Note: The NC port is used to detect the opening and closing status of the door. Only the Lockly Guard Electromagnetic Lock supports this function. If you use a third-party Electromagnetic Lock other than the Lockly Guard Electromagnetic Lock, you do not need to connect this NC cable.
2.3 Installation Diagram 2.3.1 Wired Installation Access Control Power Supply DC 12V GND PUSH- Power Supply V+ VPUSH Power Supply NO OR NC COM Electromagnetic Lock V+ V- Access Control Electromagnetic Lock LOCK NC NC Exit Button BUTTON-SW GND1 2.3.
2.4 Understanding Your New Lock After the installation of your new Lockly Guard, understanding some key functions of operating your smart lock is important. The next sections will walk you through configuring Access Codes, adding fingerprints, registering RFIDs and other features of your lock. For any questions you can always visit Locklypro.com/support for assistance.
2.5 Pair Lock with the LocklyPro App To pair your lock with the free LocklyPro App mobile app, you must have your Activation Code available. The Activation Code is specific to your lock and is located on the Activation Code Card included with you smart lock. ÕÛÛÐ ÌØ×Í ÝßÎÜÿ ßÝÌ×ÊßÌ×ÑÒ ÝßÎÜ The Activation Code is unique to each specific lock. DO NOT LOSE IT. Keep it in a safe place, as you will not be able to re-pair or reset your lock without it. LOCKLY.
2.6 Rebooting Your Lock Reboot Lockly Guard in case of power failure or malfunction. NOTICE No settings will be changed and all Access Codes will still be stored within Lockly Guard. Press and release the reboot button when you want to reboot the lock. Your Lockly Guard will beep once after reboot. Only reboot when necessary. To reboot, find the reboot button located on the bottom of the exterior side of Lockly Guard Ingress lock.
3.1 Programming Mode Program Button To enter Programming Mode, press the program button at the bottom of Lockly Guard Ingress. And you will see the shield logo and hear a short beep. Enter "Activation code" then tap Number to enter Programming Mode. Mode Add / Delete / Check Access Codes Fingerprint or RFID Card Pair Vision Connect Hub Reactivate Bluetooth Restore Factory Settings After entering Programming Mode, you should see the screen as displayed to the right on your Lockly Guard Ingress keypad.
3.2 Configuring Access Codes There are a total of five (5) buttons on the keypad as shown in the example image to the left. The numbers in each button may differ than what is shown on your device than what is displayed here. To enter your required digit, just simply press the circle where your number is shown. You do not need to press the actual number as anywhere within the circle will suffice. The button on the bottom is the OK button.
While in Programming Mode, select “1PG” to add an Access Code. If you are not in Programming Mode, please see Section 3.1 to enter Programming Mode. After pressing “1PG” then press “1AD” and select "Pd" to add an Access Code. Enter your new 6 - 8 digit Access Code and press when you are finished. You will then re-enter the code to confirm your new Access Code. Remember, just touch the digit you need within the circle around each 3 numbers. There is no need to touch the exact location of the number.
3.4 Deleting an Access Code While in Programming Mode, select “2DE” to delete an Access Code. If you are not in Programming Mode, please see Section 3.1 to enter Programming Mode. After pressing “1PG” then press “2DE” and select "Pd" to delete an Access Code. Active Access Codes will then be displayed on the screen in sequence from left to right, top to bottom. In the example shown on the left, the Access Code displayed is 135790.
3.4 Deleting an Access Code (Continued) 1 There are no There Accesare Codes is only oneAccess AccessCode Code saved in twoset. incidents where your 2 There The factory default Access the smart lock. At least one code must Code cannot be deleted. be registered. Please add another Access Code before attempting to delete the existing code. No Access Codes Set Only one Active Access Code 3.5 Checking the Access Codes While in Programming Mode, select “3CH” to check registered Access Codes.
3.5 Checking the Access Codes(Continued) If there are no Access Codes registered in your smart lock, Check Access Code mode will be invalid. The default Access Code will not be shown on the display keypad, and you will see the following screen shown to the left instead. 3.6 Adding a Fingerprint We are using an advanced biometric sensor, providing the most secure fingerprint authentication. For security reasons, Lockly Guard will only accept fingerprint patterns that consist of cross intersection points.
3.6 Adding a Fingerprint (Continued) The fingerprint sensor equipped in your smart lock is loaded with powerful fingerprint algorithms to extract only metadata from fingers, even in poor conditions. Placing your finger on the sensor correctly helps consistency in fingerprint recognition. The following directions and tips will guide you on how to scan an optimal fingerprint image. CARD SECTION 3.
3.6 Adding a Fingerprint (Continued) Your Lockly can register up to ninety-nine (99) fingerprints. Please read the following sections if you want to add or delete fingerprints. We recommend using your app to add fingerprints, however, the following section can show you without using the app. While in Programming Mode, select “1AD” to add an Fingerprint. If you are not in Programming Mode, please see Section 3.1 to enter Programming Mode.
3.6 Adding a Fingerprint (Continued) Note: For reference, please keep a record of your fingerprint registration number to distinguish whom it was registered to. Scan your finger by lightly placing your designated finger on the sensor until you hear a beep. Lift your finger and repeat the process slowly until the digit “6” shown on the screen becomes “1”. If you have successfully scanned and registered your fingerprint, you will hear a long beep, and the video doorbell light indicator will blink green.
3.8 Deleting Fingerprint While in Programming Mode, select “2DE” to delete a Fingerprint. If you are not in Programming Mode, please see Section 3.1 to enter Programming Mode. After pressing “1PG” then press “2DE”, select “FP” to delete a fingerprint. Your registered fingerprint numbers will be displayed on the screen. Tap number to rotate to the next registered fingerprint. When you have found the fingerprint ID you want to delete, press and hold the OK button for 3 seconds to delete.
3.9 Adding RFID While in Programming Mode, select “1AD” to add an RFID card. If you are not in Programming Mode, please see Section 3.1 to enter Programming Mode. After pressing “1PG” , then press “1AD” select “Id” to add an RFID card. 1. Put the RFID card to the RFID card sensor position on exterior panel. CARD SECTION 3.9 2. PASS will show on the keypad once card is registered successfully.
3.10 Deleting RFID While in Programming Mode, select “2DE” to delete an RFID card. If you are not in Programming Mode, please see Section 3.1 to enter Programming Mode. After pressing “1PG” , then press “2DE” select “Id” to delete an RFID card. Your registered RFID card will be displayed on the screen. Tap the screen to show the next registered RFID.
3.11 Adding a Wireless Device While in Programming Mode, select “2PR” to add or delete a wireless device. If you are not in Programming Mode, please see Section 3.1 to enter Programming Mode. After pressing “2PR”, select “AD” to add a wireless device. You have entered the pairing mode when "PR" button flashes. You have the options to pair "01 " Wireless Transceiver or "02" Wireless Doorbell. Select the wireless device you want to pair.
3.12 Deleting a Wireless Device While in Programming Mode, select “2PR” to add or delete a wireless device. If you are not in Programming Mode, please see Section 3.1 to enter Programming Mode. After pressing “2PR”, select “DE” to delete a wireless device. You have entered the pairing mode when "PR" button flashes. You have the options to delete "01" Wireless Transceiver or "02" Wireless Doorbell. Select the wireless device you want to delete.
3.13 Pairing via Bluetooth In order to setup the Lockly Guard Ingress to another smart phone, you will need to enter the programming mode. While in Programming Mode, select “3BL” to pair a new smart phone. If you are not in Programming Mode, please see Section 3.1 to enter Programming Mode. After pressing “3BL”, the BL icon will flash and you will here short beeps. You need to wait and allow the pairing of new devices. You will hear long beep and the green light will be on, if the pairing is successful.
Lockly Guard Smart Lock can be unlocked using multiple ways - via your stored Access Code, registered fingerprint, smartphone with Bluetooth, the physical key supplied with your lock, or voice. Slide your hand across the screen to activate the keypad. Enter your 6 to 8 digit Access Code followed by the OK button. Press OK anytime to reset if you entered the wrong digit. OK Button NOTICE If the Access Code entered is correct, the door will unlock.
Unlocking Place a registered finger to the fingerprint scanner located on the exterior side of the lock to the right. To register a fingerprint, please see Section 3.6. If your fingerprint is registered and acknowledged, you will hear a “beep” sound and a Green LED will light up on the fingerprint scanner. You can then open the door. If you see a Red LED, it means your fingerprint is not recognized. You must wait until the red LED is off to try again.
4.4 Locking/Unlocking with App You must have the LocklyPro App iOS or Android app installed in order to lock and unlock with smartphone and to access video doorbell feature. Please download the app by visiting the link below or search “Lockly” from the correct app store. Scan or visit Locklypro.com/app 26 SECTION 4.
4.5 Safe Mode - Overview Lockly Guard will enter Safe Mode when three (3) consecutive wrong Access Codes are entered within 5 minutes. A 15 second video will be recorded once the lock entered into Safe Mode. When in Safe Mode, the lock status icon will start to flash. To disable Safe Mode, you must unlock the door using the correct fingerprint or enter the correct Access Code twice in a row. Activate the keypad by pressing and holding for 3 seconds.
4.6 Disabling Safe Mode There are three (3) ways to disable Safe Mode. Option 1 - Entering Correct Access Code Activate the keypad by pressing and holding for 3 seconds. Enter the correct Access Code twice (2) when the keypad is available, pressing after every time the Access Code is entered. Option 2 - Lockly Bluetooth App Use the app that is synced to your Lockly to disable Safe Mode by unlocking the door.
4.8 Tamper Switch The tamper switch is setup at the back of the Lockly Guard Ingress. It is triggered when there is a forceful movement or usual displacement of the device. When the tamper switch is triggered, the light indicator and shield logo on the screen flashes. The buzzer alarms for 30s and the app will notify that lock is tampered. You can stop the buzzing alarm by unlocking with fingerprint, password, ID card or app.
5.1 Video Doorbell - PGI303(Continued) When the doorbell is pressed, you will receive a notification through the LocklyPro App. Once you tap on the notification, app will automatically open to allow you to see who's at your door. Tap the Call icon to initiate conversation. Enhanced Alert Notification Ingress Vision has an enhanced alert notification feature. When someone rings your doorbell and you were unable to answer, you will receive a 2nd alert notification.
5.1 Video Doorbell - PGI303(Continued) Ingress Vision enables you to attend to your door when you are not at home. While using the app, you can use the icons below to view, initiate conversations and unlock door. Live View You can open the LocklyPro App and tap on the camera to see what Vision sees at all times. Microphone Tap mic to mute or unmute. End Call Tap icon to hang up without opening the door. Unlock Tap icon to unlock door. SECTION 5.
5.1 Video Doorbell - PGI303(Continued) Video Recording on the log history on your LocklyPro App. Vision automatically initiate video recording when below conditions take place: Keypad was used * Motion was detected* Doorbell button was pushed Offline Access Code™ was used* eKey was used* Wrong (PIN) access code was used and lock entered in to Safe Mode REMINDER: - Video recordings can be customized through the LocklyPro App settings*.
6.1 Offline Access Code TM (OAC) The Offline Access CodeTM (OAC) is a unique feature of our smart lock. It allows you to grant access to guests remotely without guests needing to download the app. To use the OAC feature, make sure you download the LocklyPro App for iOS or Android first, and sync your smart lock to your mobile device. OAC can only be issued by the administrative owner of the lock. From there, you can then issue an Offline Access CodeTM within the app.
6.2 eBadge An eBadge is a unique code that can be issued to another user giving them door access for a specific reoccurring time frame or a valid period of time. It requires them to download the free LocklyPro App and access can only be gained through the app (not the fingerprint reader). 1 2 3 7Y20LOCKLY 4 34 5 6 SECTION 6.
6.2 eBadge (Continued) 1 To set up and send a code in the Lockly app, go to > Access > eBadge (at top) > Add eBadge, then follow the on-screen prompts. 2 Confirm you want to add an eBadge. 3 Give the eBadge name you will recognize. Provide a custom message that will be sent to the user. 4 Select type of access: either a valid period of time or ongoing reoccurring (can be revoked at anytime). 5 Review and confirm access type. 6 Share unique eBadge code. 6.
6.4 Multi Units and Tiered Verifications Lockly Guard Ingress can be programmed to manage a single unit or multiple units with sub-admin management access. Example of Single Unit (Office Employee access management) Enter the employee number > Confirm > enter the password (PIN Genie Keypad) > Confirm, that is, enter the employee number before entering the password. Note: up to 100 groups of passwords can be added.
7.1 Important Notes Auto Lock Feature You can program the auto lock timing through the LocklyPro App. If auto-lock is not activated and door is still open, the touch-screen will remain lit, simply press the on the keypad to lock. One-Touch Locking You can always manually lock by touching anywhere on the touchscreen. Lockly smart lock is shipped with this feature already activated. You may deactivate this feature through the LocklyPro App.
9.1 Safety Precautions Please read all instructions carefully. Remind all Lockly Guard users of the safety precautions. Read the following instructions for your own safety Do not attempt to disassemble the smart lock by yourself. It can cause product damage, void warranty, and cause injuries. Do not use any inappropriate tools that can cause damages or malfunction to your lock. Always make sure your door is securely closed and locked when you leave your house to prevent unwanted entry.
9.1 Safety Precautions(Continued) - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
We’re here to help! help@Lockly.com https://Locklypro.
© Copyright 2022 Lockly All rights reserved USA Patent No. US 9,881,146 B2 | USA Patent No. US 9,853,815 B2 | USA Patent No. US 9,875,350 B2 | USA Patent No. US 9,665,706 B2 | USA Patent No. US 11,010,463 B2 | AUS Patent No. 2013403169 | AUS Patent No. 2014391959 | AUS Patent No. 2016412123 | UK Patent No. EP3059689B1 | UK Patent No. EP3176722B1 | Other Patents Pending The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc.
