R REV:6.0 ERP机型:PL35G2UQ-GL-SMT00010A-V1 ERP P/N: 描述:安装指引:PL35G2UQ/PGD1128FPW,SMT000,REV.G(MPGD1128FPW20210721), 196*196MM,128G双粉纸,双面4C+2专(2915C+7540C),印刷过哑油,12页24面装订本+封底面, (封底面为折叠页,展开尺寸:784x196mm),ROHS2.0,REACH,POPS,PAHS,PROP65 C M Y K 7540C Designed:Sunny Connect with us 正面 2915C Date:2021-07-21 @meetlockly | #LOCKLY VISION ™ We’re here to help! Email: help@LOCKLY.com Reference installation parts overview foldout.
Welcome! This guide will walk you through step-by-step how to install and get your LOCKLY VisionTM up and running. Installation generally takes less than 30 minutes. If you have any questions please reference our online support at: LOCKLY.com/support or call (669) 500-8835 for help.
Preparation To complete the installation you will need: Phillips Screwdriver Flathead Screwdriver Tape measure or ruler Prepare door: remove existing deadbolt or use provided template to bore new holes. 2-⅜" (60mm) or 2-¾" (70mm) 1-⅜" (35mm) to 2" (50mm) Cross-bore 2-⅛" (54mm) 1" (25mm) CAUTION: lock contains electrostatic-sensitive (ESD) parts.
Step 1 ADJUST DEADBOLT AND INSTALL Deadbolt slot must align to the center of the door hole. Adjust as shown if needed. 2-3/4" (70mm) or 2-3/8” (60mm) The deadbolt comes set to 2-3/4" (70mm). Adjust length to 2-3/8” (60mm) if necessary. (wear gloves to protect from possible pinching). B A B Push the crank A to extend the deadbolt B C D Deadbolt comes set at 2-3/4" (70mm).
Step 1 ADJUST DEADBOLT AND INSTALL continued Extend the deadbolt by inserting a flat-head screwdriver into the slot and turning clockwise. Insert the deadbolt into mortise flush with door edge, make sure that the right side is up and the slot is in the vertical position. Secure with 2 K screws.
Step 2 INSTALLING EXTERIOR ASSEMBLY (B) Check the exterior assembly (B) alignment to door hole and deadbolt before peeling off film on adhesive strips. Peel film from adhesive strips and make sure torque blade is in the vertical position with the deadbolt extended. Place assembly and torque blade through the deadbolt slot and guide connection cables through the cross-bore hole under the deadbolt as shown. Complete mounting by aligning and securing until flush to exterior door surface.
Step 3 INSTALLING INTERIOR ASSEMBLY (G) 2: Align and secure mounting plate with adhesive strips. Guide connection cables through the hole and secure to the lower left notched hole. 1: Check interior mounting plate (K) alignment to your door hole before securing with adhesive strips. Remove key when finished F 2X Leave deadbolt extended 4: Use the key to ensure deadbolt locks and unlocks smoothly (no binding or rubbing).
Step 4 PREPARING DOOR SENSORS FOR INSTALLATION Do not mount (install) door sensors yet. You will install in step 7. About door sensors Door sensors provide real-time door condition status, such as the ability to verify if the door is securely closed. It also sends push notifications to your phone whenever your door opens and enables voice control with Amazon Alexa or Google assistant.
Step 4 continued PREPARING DOOR SENSORS FOR INSTALLATION When installing the door sensors, make sure the arrow on the wired sensor (P) aligns to the arrow of the sensor magnet (Q) as close as possible. (P) 3/4" (20mm) 2-3/8" (60mm) Foam pad The sensors need to be as close to level as possible. If needed, use the adhesive foam pad(s) to adjust the height of the wired sensor. 2-3/4" (70mm) Right or Left Sensors can be positioned on either left or right side (see page 10).
Step 4 PREPARING DOOR SENSORS FOR INSTALLATION continued The interior assembly comes with the pre-installed wired door sensor setup for a right swing doors with 2 ¾" (70mm) backset*. For left swing doors, re-route the door sensor wire through the side channel. Pull the foam pad then re-insert to secure the wire. Discard the excess part (e) for doors with 2 ⅜" (60mm) backset as shown below: Trim excess part (P) for doors with 2 ⅜" (60mm) backset as shown below.
Step 5 INSTALLING THE INTERIOR ASSEMBLY (G) Plug the larger cable coming through mounting plate (D) into the interior assembly (G) as shown. Tuck cable under eyelet hooks and route to the right on interior assembly (G). Connect A to B screw tightly by hand as shown. Plug X into Y , match red side of plug with red on socket - insert tightly. A X NOTE: If you need to disconnect the cable, make sure to press the snap tab to release the plug before carefully pulling it out.
Step 5 INSTALLING THE INTERIOR ASSEMBLY (G) continued RESE T PROG RAM RESE T PROG RESE T PROG RAM RAM Torque Blade Thumb turn shaft H 2X Align torque blade with thumb turn shaft, make sure both are in the vertical position. Before placing the interior assembly onto the mounting plate, ensure the thumb turn is vertical. Place the interior assembly against the mounting plate and make sure the torque blade is inserted to the thumb turn shaft.
Step 6 INSTALLING BATTERIES 1 2 IMPORTANT Install batteries 5-8 only after self-check is complete 4 3 5 6 7 8 PRESS & HOLD 1: With door open and deadbolt fully extended, place ribbon inside compartment and insert 3 batteries only (hold on inserting the 4th) in bottom row (note correct -/+ polarity). 2: Press and HOLD the program button, continue to hold and install the 4th battery. The lock will automatically start self-check (release program button once check starts).
Step 6 INSTALLING BATTERIES 3: Once self-check completes ensure the lock operates smoothly by manually locking and unlocking the door using the thumb turn on the interior assembly. The deadbolt should operate smoothly without any interference or binding. If necessary, repeat step 2 and ensure that (a) the deadbolt was extended and (b) the torque blade was inserted vertically while the deadbolt was extended. 4: Swipe your hand across the touch screen keypad, the lock should close (lock).
Step 7 INSTALLING THE DOORS SENSOR Make sure you have prepared the door sensors for installation, see step 4 LOCK SENSOR (P) Install on the interior side only. If necessary, trim tab from sensor (P) for doors with 2-3/8" (60mm) backset. Clean surface of door and doorframe, remove film from adhesive, attach and secure close to door edge as shown.
Step 7 INSTALLING THE DOORS SENSOR DOOR FRAME SENSOR (Q) Manually retract deadbolt and close door. Dry fit sensor (Q) to door frame and check for alignment. If needed, raise the height of the sensor to be more level with sensor (P) by adding 1 or 2 of the included adhesive foam pads. Once satisfied both sensors are as level as possible, remove film from adhesive and install with arrows aligned to each other with less than a 3/4" gap between each sensor.
Step 8 INSTALLING STRIKE PLATE Use the supplied door strike or use your existing as long as deadbolt operates smoothly without binding or catching. K(2X) L N IMPORTANT: because doors and frames vary in design it may be necessary to make slight adjustments to your strike plate and/or dust box in order to ensure smooth deadbolt operation. This is very important.
Step 9 PAIRING VISION CONNECT WITH LOCK To enable video doorbell, live monitoring and voice control with Google Assistant or Amazon Alexa, you will need to setup the included Vision Connect WI-Fi hub and pair it with the LOCKLY VisionTM deadbolt smart lock + video doorbell. VISION CONNECT OVERVIEW Antenna LED status lights Reset LAN cable Power adapter TF card IMPORTANT: Vision Connect stores recorded video on the included TF card.
Step 9 continued LOCKLY® APP & UNIQUE ACTIVATION CODE Before connecting Vision Connect Hub download the LOCKLY app on your smartphone. It’s required to finish setup and to set (pair) the connection between hub and lock. Scan, visit app store, or go to LOCKLY.com/app Additionally, you'll need the Activation Card with unique pre-paired QR code to your lock. The card is located in the packaging that your lock came in. This QR code can also be found at the bottom of Vision Connect Hub.
Step 9 APP SET UP continued Set up an account by registering your LOCKLY VisionTM in the LOCKLY app. Registration is also mandatory to activate your locks warranty. 1 2 3 After successful registration, select "add a new device" (you can also get to this from the menu in the top left), select Vision, and follow the step-by-step on screen instructions. You can also reference these steps on following pages.
Step 9 LOCATION GUIDELINES continued The Vision Connect Hub connects directly to your Wi-Fi router using the provided LAN cable. Choose an appropriate location for the hub for optimum performance (see below). For optimum connectivity, it is recommended that the hub be no further away from the lock than 100 feet, placed 3 feet (1 meter) off the ground.
Step 10 VISION CONNECT HUB SETUP continued Ensure the TF card that comes with Vision Connect is properly inserted. Connect LAN cable to closest Wi-Fi router to the LOCKLY VisionTM lock (<100ft). LAN cable (S) (included) TF card (included) Connect power cable and plug USB power adapter into outlet. Wait 2 minutes for hub to self calibrate. Once LEDs turn RED and blink yellow. Vision Connect is now ready to connect to your iOS or Android device.
Step 10 PAIR VISION LOCK TO APP continued Launch the LOCKLY® App and select "add a new device", then select Vision. You will be prompted to scan the QR code from the Activation Card or Vision Connect Hub (located at the bottom). OR LOCKLY App IMPORTANT: make sure your LOCKLY Vision has the latest firmware. Allow updates and follow instructions if prompted. For more info, visit: http://www.support.LOCKLY.
VISION CONNECT STATUS & TROUBLESHOOTING LED INDICATORS Solid red ON HUB After connecting LAN cable and power adapter, wait for 2mins for Vision Connect to self calibrate.
Smart Home Ready VOICE CONTROL Control with Amazon Alexa or Google Assistant. Control and check your door status by using your voice through Amazon Alexa or Google Assistant. Alexa, check if my front door is unlocked? Hey Google, unlock my office door. To setup your lock to work with either voice assistant, download the Amazon Alexa or Google Home App and add a new skill for Amazon Alexa or action for Google Assistant.
INSTALLATION OVERVIEW AND PARTS LIST FCC Warning: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Go to LOCKLY.com/pages/installation to watch a video version of this installation guide.