WWW.LOCKLYPRO.
Table of Contents Section 1 - Product Highlights 1.1 Product Features 1 Section 2 - Product Overview 2.1 2.2 2.3 2.4 2.5 2.6 2.
1.1 Product Features Hack-proof PIN Genie Touchscreen Keypad Digits are randomly displayed on the key pad ensuring access codes to be undetectable to intruders after repeated use. Numbers are randomly distributed across 4 buttons, with 3 numbers in each button. Users can press any button showing their number. Location of the numbers are always different everytime someone uses the keypad, making it hard for prying eyes to guess the correct code.
2.1 Product Overview - Outside Keypad Buttons Touchscreen Bluetooth icon Screen Lock Icon Low Battery Alert OK Button Fingerprint Sensor Bluetooth light Handle Key Hole Cover Key Hole 9V Battery Backup Socket Reboot Button 2 SECTION 2.
2.2 Product Overview - Inside Battery Cover Screw Battery Compartment 4 x AA Alkaline Batteries(Included) Battery Cover Reset Button Program Button Low Battery Indicator/ Door Lock Button Inside Handle SECTION 2.
2.3 Understanding Your New Lock After the installation of your new Lockly, understanding some key functions of operating your smart lock is important. The following guides will walk you through resetting a lock, adding Access Codes, deleting Access Codes, adding and deleting fingerprints, and also how to configure your OAC(Offline Access Code™). For any questions you can always visit https://Locklypro.com/support for assistance.
2.4 Reset Button In order to restore the Lockly to factory default settings, you must have your “Activation Code” available. The Activation Code can be found on the Activation Code Card that came with your smart lock. After you have the Activation Code ready, push the reset button on the back panel of the Lockly to perform your reset. See below to see which Reset Process applies for you. Once the smart lock has been reset, all the data previously stored will be deleted.
2.5 Rebooting Your Lock NOTICE Reboot Lockly in case of dead battery or malfunction. No settings will be changed and all Access Codes will still be stored within Lockly. Press and release the reboot button when you want to reboot the lock. Your Lockly will beep once after reboot. Only reboot when necessary. To reboot, find the reboot button located on the bottom of the exterior side of Lockly lock. The reboot button is located in the middle of the two 9V battery backup sockets.
2.6 Low Battery When the battery is in seriously low condition, Lockly will make continuous beeping sounds in addition to the flashing low battery icon on the touch screen. You should replace batteries immediately to avoid your smart lock from shutting down. When your smart lock low-battery warning alert finally dies, you will have 3 chances to unlock your smart lock either by a password, APP or fingerprint. If the unlock was successful, the low-battery warning alert will be on for 1 minute.
2.7 Changing The Battery Under normal use, the Lockly battery will last up to a year. Please check battery levels regularly and change your batteries when the low battery notification is issued. For best practice, always use new batteries by a major brand. Open the battery compartment cover and insert four (4) new AA alkaline batteries as shown. Be sure to unscrew the screw located on the top of the cover first by unscrewing counter clockwise before sliding the cover up. 3 AA 1.
3.1 Configuring Access We recommend pairing your lock to your smart phone to manage your access codes. Section 3.1 - 3.9 refers to locks not paired with a smart phone. Once paired with a smart phone, the Program button will be disabled. How to Use the Keypad There are a total of five (5) buttons on the keypad as shown in the example image to the left. The numbers in each button may differ than what is shown on your device than what is displayed here.
3.2 Entering Programming Mode To enter Programming Mode, remove the battery compartment cover on the interior side of the Secure to expose the Reset and Program buttons. Simply press the Program button to enter programming mode. Program Button Note: Program button will be disabled once synced to a smart phone. Configure all settings via synced smart phone. Access Codes previously added by Programming mode will be cleared. To end Programming Mode, press the Program button anytime.
3.3 Adding an Access Code While in Programming Mode, select “1AD” to add an Access Code. If you are not in Programming Mode, please see Section 3.2 to enter Programming Mode. After pressing “1AD” press “Pd” to add an Access Code. Enter your new 6 - 8 digit Access Code and press when you are finished. You will then re-enter the code to confirm your new Access Code. Remember, just touch the digit you need within the circle around each 3 numbers. There is no need to touch the exact location of the number.
3.3 Adding an Access Code (Continued) If you have successfully entered your new Access Code twice, you will see the new code displayed here. In this example, we chose 654321. Press to Confirm or to cancel. To exit or cancel, you can always press or If the two (2) Access Codes you entered does not match, an error message will appear on the screen (As shown to the left). Press OK to return to the Programming Screen and try again. See Section 3.3 OK Button 12 SECTION 3.
3.4 Deleting an Access Code While in Programming Mode, select “2DE” to delete an Access Code. If you are not in Programming Mode, please see Section 3.2 to enter Programming Mode. After pressing “2DE” press “Pd” to delete an Access Code. Example Only Active Access Codes will then be displayed on the screen in sequence from left to right, top to bottom. In the example shown on the left, the Access Code displayed is 1 3 5 7 9 0 .
3.4 Deleting an Access Code (Continued) Once you have selected the Access Code you want to delete, Lockly will ask you to confirm deletion by showing you the Access Code you are deleting, in this example, 1 3 5 7 9 0. Press NOTE to cancel. There are two incidents where your Access Code cannot be deleted. There are no Access Codes set. The factory default Access Code cannot be deleted. No Access Codes Set 14 to delete, or There is only one (1) Access Code saved in the smart lock.
3.5 Checking the Access Codes While in Programming Mode, select “3CH” to check registered Access Codes. If you are not in Programming Mode, please see Section 3.2 to enter Programming Mode. Active Access Codes will then be displayed on the screen in sequence from left to right, top to bottom. In the example shown on the left, the Access Code displayed is 1 3 5 7 9 0 . OK Button Rotate through the different Access Codes by touching any number on the screen.
3.6 Adding a Fingerprint In this section, you will learn how to register a fingerprint to your new smart lock. Fingerprint registration is only available in the Lockly Secure Plus / Pro. We are using an advanced biometric sensor, providing the most secure fingerprint authentication. For security reasons, Lockly will only accept fingerprint patterns that consist of cross intersection points. Patterns with no cross intersection points will not be acceptable.
3.6 Adding a Fingerprint (Continued) While in Programming Mode, select “1AD” to add an Access Code. If you are not in Programming Mode, please see Section 3.2 to enter Programming Mode. After pressing “1AD” press “FP” to register a Fingerprint. Upon pressing “FP”, you will enter Fingerprint Registration Mode and you will see a green LED ring light up on the fingerprint panel on the exterior side of Lockly Guard™ Duo(679D).
3.6 Adding a Fingerprint (Continued) NOTICE Please make sure your fingers are clean from dirt and oils before scanning your fingerprint. Make sure the sensor is also clean by taking a soft cloth and wiping the surface. Scan your finger by lightly placing your designated finger on the sensor until you hear a beep. Lift your finger and repeat the process slowly until the digit “6” shown on the screen becomes “1”.
3.7 Fingerprint Scanning Directions The fingerprint sensor equipped in your smart lock is loaded with powerful fingerprint algorithms to extract quality features from fingers, even in poor conditions. Placing your finger on the sensor correctly helps consistency in fingerprint recognition. The following directions and tips will guide you on how to scan an optimal fingerprint image. Sensor Core Position your finger on the center of the sensor Top View OK Side View Correct Incorrect OK SECTION 3.
3.8 Fingerprint Scanning Tips & Troubleshoot Tips for Fingerprint Enrollment and Recognition • Place your finger to completely cover the sensor with maximum contact surface. • Position the center of your finger (core) to the center of the sensor. • Hold your finger still for more than a second until you hear a beep. • Scan a finger that is clean and free from dirt. • Children ages 12 and under are not recommended to use fingerprint access due to the constant changes of their fingers during growth.
3.9 Deleting Stored Fingerprints* While in Programming Mode, select “2DE” to delete a Fingerprint. If you are not in Programming Mode, please see Section 3.2 to enter Programming Mode. After pressing “2DE” to delete, press “FP” to delete a fingerprint. Your registered fingerprint numbers will be displayed on the screen. Tap number to rotate to the next registered fingerprint. When you have found the fingerprint ID you want to delete, press and hold the OK button for 3 seconds to delete.
3.10 Adding an RFID card While in Programming Mode, select “1AD” to add an RFID card. If you are not in Programming Mode, please see Section 3.2 to enter Programming Mode. After pressing “1AD” press "Id" to add an RFID card. Place the RFID card to the screen where the RFID card sensor is embedded. 22 PASS will show on the keypad once card is registered successfully. SECTION 3.
3.11 Deleting RFID Card While in Programming Mode, select “2DE” to delete an RFID card. If you are not in Programming Mode, please see Section 3.2 to enter Programming Mode. After pressing “2DE” press “Id” to add an RFID card. Your registered RFID card will be displayed on the screen. Tap the screen to show the next registered RFID. When you have found the RFID card you want to delete, press and hold the OK button for 3 seconds to delete. OK Button SECTION 3.
3.12 Adding Secure Link Lockly Secure Link¹ adds live status monitoring and voice control capabilities to your Lockly Smart Lock. The Secure Link is included in Lockly Guard™ Duo (PGD679DW). For all other Lockly products, the Secure Link can be purchased and added anytime. To set up the Lockly smart lock with Secure Link Wi-Fi Hub and Door Sensors, launch the Lockly App on your iOS or Android device.
4.1 Locking/Unlocking with Access Codes Lockly Smart Lock can be unlocked using multiple ways - via your stored Access Code, registered fingerprint, smartphone with Bluetooth, the physical key supplied with your lock, or voice (Secure Pro only or Secure Plus with Secure Link Wi-Fi Hub installed) OK Button Slide your hand across the screen to activate the keypad. Enter your 6 to 8 digit Access Code followed by the OK button. Press OK anytime to reset if you entered the wrong digit.
4.1 Locking/Unlocking with Access Codes (Continued) Lock your Lockly by pressing the OK Button or by brushing your hand across the screen anytime when the door is closed. The smart lock will also auto-lock after unlocking based on your set auto-lock settings.keypads. You may toggle between two types of keypad displays to enter your Access Code. The fixed digit version and the PIN Genie version (Recommended). Press and hold the OK Button for 3 seconds to toggle back and forth between the two keypads.
4.2 Locking/Unlocking Lockly with Fingerprints Unlocking Place a registered finger to the fingerprint scanner located on the exterior side of the lock to the right. To register a fingerprint, please see Section 3.6. If your fingerprint is registered and acknowledged, you will hear a “beep” sound and a Green LED will light up on the fingerprint scanner. You can then push down the handle and open the door. If you see a Red LED, it means your fingerprint is not recognized.
4.3 Locking/Unlocking Lockly with App You must have the Lockly iOS or Android app installed in order to lock and unlock with smartphone and connect with voice assistants like Hey Google. Please download the app by visiting the link below or search “Lockly” from the correct app store. Scan or visit Locklypro.com/app 28 SECTION 4.
4.4 Locking/Unlocking using RFID Light up the screen by touching the keypad. Place your RFID card closer to the panel. Push down the handle and open the door after it chimed. SECTION 4.
4.5 Locking/Unlocking with Physical Key Exterior View To unlock your lock using the physical key (included), open the key cover on the handle by turning the cover to reveal the keyhole. Insert your key and turn clockwise or counter clockwise to lock or unlock the door. 30 SECTION 4.
4.6 Locking/Unlocking with Door Handle This smart lock is built with an anti-friction latch and deadbolt throw for added security. The latch throw can be setup to auto lock based on your customized timing through the Lockly app. The deadbolt throw is connected to the door handle. To UNLOCK push the handle downwards and push door to open. This action is necessary to open your door whenever you access by keypad, fingerprint, smartphone App or via Voice Assistants.
4.7 Safe Mode - Overview Lockly will enter Safe Mode when three (3) consecutive wrong Access Codes are entered within 5 minutes. When in Safe Mode, the lock status icon will start to flash. To disable Safe Mode, you must unlock the door using a registered fingerprint, access via mobile App, unlock using the keyhole, pressing the Lockly logo button on the interior panel or by pushing down the interior handle or enter the correct Access Code twice in a row.
4.7 Disabling Safe Mode There are four (4) ways to disable Safe Mode. Option 1 - Entering Correct Access Code Activate the keypad by pressing and holding for 3 seconds. Enter the correct Access Code twice (2) when the keypad is available, pressing the Access Code is entered. after every time Option 2 - Lockly Bluetooth App Use the app that is synced to your Lockly to disable Safe Mode by unlocking the door.
4.8 Rain Mode Like other digital electronic products water can trigger to activate the touchscreen and sensor which may cause the batteries to drain. To protect the lock and extend battery life, you can setup your Lockly to enter Rain Mode to shut off keypad and fingerprint reader whenever rain or water is detected. Activate this feature on the Lockly app. While you are within the Bluetooth range or remotely connected thru Wi-Fi hub (Secure Link), go to Settings > Rain Mode and toggle the button to turn ON.
4.9 Shine Mode Lockly touchscreen keypad brightness was designed for optimum battery life. However, some users may need to adjust the brightness to their convenience to enter access codes. Swipe your fingers across the keypad to light up to its normal brightness. To adjust brightness, long press the upper left button for 3 seconds. The touchscreen keypad with automatically return to normal brightness after the screen dimmed. SECTION 4.
4.10 Welcome Mode Welcome Mode temporarily disables auto locking, keeping the door open for a specified period of time eliminating the need to enter access codes, fingerprint or using Mobile App. Enable this feature through the Lockly App. Go to > Settings > Enable Welcome Mode, then slide button to enable and set the specific time you require your door unlocked. 36 SECTION 4.
5.1 Offline Access Code™ (OAC) The Offline Access Code™ (OAC) is a unique feature of our smart lock. It allows you to grant access to guests remotely without guests needing to download the app. To use the OAC feature, make sure you download the Lockly app for iOS or Android first, and sync your smart lock to your mobile device. OAC can only be issued by the administrative owner of the lock. From there, you can then issue an Offline Access Code™ within the app.
5.2 Sub Admin Access Sub-Admin Access can be created to grant access for others to be able to control your lock and grant access to others via Bluetooth when within range of your Lockly smart lock. The sub-admin permission can be setup through the Lockly App then Add A New User. You can select the Validity Period and User Permissions of the sub-admin. Sub Admins will not be able to access the lock remotely but Sub Admin will be able to grant limited access codes to users when within Bluetooth range.
6.1 Re-keying Lockly smart lock comes with a 5-pin cylinder which can be replaced with regularly purchased DIY re-keying kit available in the market. If you are not familiar with this process, please contact a professional locksmith. For more information, visit: http://support.Lockly.com/faq/rekeying/ SECTION 6.
7.1 Important Notes Auto Lock Feature Your lock can be programmed to auto-lock between 5-300 seconds after the door opening. You can select the timing through the Lockly App. If auto-lock is not activated and door is still open, the touchscreen will remain lighted, simply press the on the keypad to lock. One-Touch Locking You can always manually do a quick lock by touching anywhere on the touchscreen. Lockly smart lock is shipped with this feature already activated.
8.1 Cleaning Making sure your Lockly is clean is best practice to ensure optimal product use. Follow the DOs and DON’Ts below. DO DON’T • Rinse the touchscreen with warm water prior to cleaning. • Don’t use abrasives, high alkaline cleaners, or gasoline to clean your lock. • Use the application of soap with a damp, lukewarm cloth. • Don’t apply cleaning detergent directly in sunlight or at high temperatures. • Air dry or wipe dry with a soft microfiber cloth to avoid scratches.
8.2 Calibrating the Lock If the lock was not used for a long period of time, the lubrication of the inside mechanism may affect its unlocking responses. Dust and freezing temperatures may also cause your lock to delay or not to respond to unlocking. Calibrate your lock to maintain its responsiveness. Calibration may take 60 seconds to finish. You will hear the lock unlocking for multiple times. The unlocking sound will stop once the calibration is finished.
9.1 Safety Precautions Please read all instructions carefully. Remind all Lockly users of the safety precautions. Read the following instructions for your own safety Do not attempt to disassemble the smart lock by yourself. It can cause product damage, void warranty, and cause injuries. Do not use any inappropriate tools that can cause damages or malfunction to your lock. Always make sure your door is securely closed and locked when you leave your house to prevent unwanted entry.
FCC Warning: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: 1. L’appareil ne doit pas produire de brouillage; 2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
To ensure you have access to the most updated and newly added features of your Lockly smart lock, please visit: www.locklypro.com/679D DUO (679D) We’re here to help! prosales@lockly.com locklypro.com/support © Copyright 2021 Lockly All rights reserved USA Patent NO. US 9,881,146 B2 | USA Patent NO. US 9,853,815 B2 | USA Patent NO. US 9,875,350 B2 | USA Patent NO. US 9,665,706 B2 | USA Patent NO. US 11,010,463 B2 | AU Patent NO. 2013403169 | AU Patent NO. 2014391959 | AU Patent NO.