R REV:1.0 ERP 机型:PL45H1UQ-US-SMT00030A-V1 ERP P/N: 描述:说明书:PL45H1UQ/PGD238,SMT000,REV.A(UMPGD23820220907), 140x190mm,80g书纸,双面单黑印刷,16页32面装订本,RoHS2.0,REACH, Prop65,POPs,PAHs K Designer:Sabrina Date:2022-09-07 WWW.LOCKLYPRO.
Table of Contents Section 1 - Product Highlights 1.1 Product Features Section 5 - Advanced Features 1 Section 2 - Product Overview 2.1 Product Overview- Exterior 2 2.2 Understanding Your New Lock 3 2.3 Locking/Unlocking with App 3 2.4 Rebooting Lockly Guard 4 2.5 Low Battery 5 2.6 Changing the Battery 6 5.1 Offline Access CodeTM (OAC) 25 Section 6 - Important Notes 26 Section 7 - Cleaning 27 Section 8 - Safety Precautions 27 Section 3 - Using Your Smart Lock 3.
1.1 Product Features Patented Hack-proof PIN Genie Keypad Digits are randomly displayed on the keypad ensuring access codes to be undetectable to intruders after repeated use. Numbers are randomly distributed across 4 buttons, with 3 numbers in each button. Users can press any button showing their number. Location of the numbers are always different everytime someone uses the keypad, making it hard for prying eyes to guess the correct code.
2.1 Product Overview- Exterior RFID Card Reader Touchscreen Keypad Battery Indicator OK Button Key Hole Welcome/ Safe Mode Exterior Handle Fingerprint Reader Battery Compartment *Operated by 4 X AA size alkaline batteries ( not included ) Program Button Battery Cover 9V alkaline battery Reboot Button 2 SECTION 2.
2.2 Understanding Your New Lock NOTICE The Default Access Code is 123456 After the installation of your new Lockly Guard, understanding some key functions of operating your smart lock is important. The following guides will walk you through resetting a lock, adding and deleting Access Codes, adding and deleting fingerprints, adding and deleting RFID cards and also how to configure your OAC (Offline Access Code™) For any questions you can always visit http://LocklyPro.com/support for assistance. . 2.
2.4 Rebooting Lockly Guard NOTICE Reboot Lockly Guard in case of dead battery or malfunction. No settings will be changed and all Access Codes will still be stored within Lockly Guard. Press and release the reboot button when you want to reboot the lock. Your Lockly Guard will beep once after reboot. Only reboot when necessary. To reboot, find the restart button from the bottom of Lockly Guard. You will need something small such as a paperclip, to press the reboot button.
2.5 Low Battery When the battery is in seriously low condition, Lockly Guard will make continuous beeping sounds in addition to the flashing low battery icon on the touch screen. You should replace batteries immediately to avoid your smart lock from shutting down. When your smart lock low-battery warning alert finally dies, you will have 3 chances to unlock your smart lock either by a password, APP or fingerprint. If the unlock was successful, the low-battery warning alert will be on for 1 minute.
2.6 Changing the Battery Open the battery compartment cover and insert 4 AA alkaline battery as shown below. • Make sure the batteries are correctly oriented. • Replacement of batteries does not affect programmed data. • Replace only with new batteries. DO NOT mix with used batteries. 1 1 2 3 2 Use a screwdriver to push the back screw stopper up then loosen the screw. Remove the battery cover. Unplug the terminals of the battery compartment and install the battery.
3.1 Configuring Access We recommend pairing your lock to your smart phone to manage your access codes. Section 3.1 - 3.11 refers to locks NOT paired with a smart phone. Once paired with a smart phone, the Program button will be disabled. Your new Lockly Guard Access Code can be any combination of 6 to 8 digits. Once a new Access Code is entered, the Default Access Code of 123456 would be deleted.
3.2 Entering Programming Mode To enter Programming Mode, remove the battery cover on the bottom of the Lockly Guard to reveal the program buttons. Short press the program button to enter programming mode. Enter administrator fingerprint, RFID card, activation code* or administrator access code (the initial administrator password is 123456) then tap Program Button To end Programming Mode, press the Program button anytime.
3.3 Pairing to a New Mobile Device (Continued) PAIR LOCKLY GUARD TO APP To pair your smart lock to a new mobile phone, download the LocklyPro app on your new mobile phone then use the same account to login to your LocklyPro App on the new mobile device. If you're pairing your Lockly Guard to a new LocklyPro app account, follow the steps below 1. On the old LocklyPro app account, go to Settings > Reset and pairing >Perform Factory Reset. 2. Download, register and log in to the new LocklyPro app account. 3.
3.4 Adding an Access Code Enter the App Access Management settings then tap "Add New User". Select the the type of user you wish to add access, “Trusted User”, “Guests”, “One-Time Access”. For example, select Trusted User, enter the user’s name and set the Access Code. Re-enter the access code, then tap “Confirm” to successfully add the new access code. An access code is a combination of 6 to 8 digits. The Administrator can set up to 1033 sets of access codes and these can only be added through the App.
3.6 Adding a Fingerprint We are using an advanced biometric sensor, providing the most secure fingerprint authentication. For security reasons, Lockly Guard will only accept fingerprint patterns that consist of cross intersection points. Patterns with no cross intersection points will not be acceptable. Please check your fingers before registration to make sure the finger you want to register will be acceptable by our system. Otherwise, use an alternative finger to ensure successful registration.
3.7 Add/Delete Fingerprints Fingerprints can only be added or deleted through the App. On the App Access Management, select Fingerprint, then tap "Add New Fingerprint". Scan your finger by lightly placing your designated finger on the sensor until you hear a beep. Lift your finger and repeat the process until the digit “6” shown on the screen becomes “1”. If you have successfully scanned and registered your fingerprint, you will hear a beep and PASS will be displayed on the keypad. Press to exit.
3.8 Fingerprint Scanning Directions The fingerprint sensor equipped in Lockly Guard is loaded with powerful fingerprint algorithms to extract quality features from fingers, even in poor conditions. Placing your finger on the sensor correctly helps consistency in fingerprint recognition. The following directions and tips will guide you on how to scan an optimal fingerprint image. Sensor Core Position your finger on the center of the sensor Side View Top View OK Correct SECTION 3.
3.9 Fingerprint Scanning Tips & Troubleshoot Tips for Fingerprint Enrollment and Recognition • Place your finger to completely cover the sensor with maximum contact surface. • Position the center of your finger (core) to the center of the sensor. • Hold your finger still for more than a second until you hear a beep. • Scan a finger that is clean and free from dirt. • Children ages 12 and under are not recommended to use fingerprint access due to the constant changes of their fingers during growth.
3.10 Adding an RFID card(Continued) The Lockly Guard keypad will lit up and show the number sequence of the RFIDs to be added. Place the card into RFID card reading area. • When RFID card is successfully added, keypad will display PASS followed by a beep. The display screen will exit automatically and lit up with PIN Genie screen. • If RFID card is not successfully added, keypad will display FAIL followed by short beeps then screen will be off.
4.1 Unlocking with Access Codes Lockly Guard Smart Lock can be unlocked using multiple ways - via your stored Access Code, registered fingerprint, RFID Card, smartphone with Bluetooth, or the physical key supplied with your lock. Slide your hand across the screen to activate the keypad. Enter your 6 to 8 digit Access Code followed by the . Press OK anytime to reset if you entered the wrong digit. If the Access Code entered is correct, the door will unlock.
4.2 Unlocking/Locking with Fingerprints Unlocking Place a registered finger to the fingerprint scanner located on the exterior handle of the lock. To register a fingerprint, please see Section 3.7. OK Button If your fingerprint is registered and acknowledged, you will hear a “beep” sound and a Green LED will light up on the fingerprint scanner. You can then push down the handle and open the door. If you see a Red LED, it means your fingerprint is not recognized.
4.3 Unlocking using RFID Push down the handle and open the door after it chimed. Light up the screen by touching the keypad. Place your RFID card closer to the panel. 18 SECTION 4.
4.4 Locking/Unlocking with Physical Key Exterior View To unlock your Lockly Guard using the physical key (supplied. Insert your key and turn clockwise or counter clockwise to lock or unlock the door. SECTION 4.
4.5 Safe Mode Lockly Guard will enter Safe Mode when ten (10) consecutive wrong Access Codes are entered within 5 minutes. When in Safe Mode, the lock status icon will start to flash. To disable Safe Mode, you must unlock the door using the correct fingerprint or enter the correct Access Code twice in a row. Activate the keypad by pressing and holding for 3 seconds. Once the screen is activated, enter the correct Access Code carefully twice, pressing after every time.
4.5 Safe Mode ( Continued ) There are four (4) ways to disable Safe Mode. Option 1 - Lockly Guard Bluetooth App Use the app that is synced to your Lockly Guard to disable Safe Mode by unlocking the door. If you have not downloaded the app to use with your smart lock, you won’t be able to use this option to disable Safe Mode. Option 2 - Physical Key There is a pair of keys included with your new lock. You may use the keys to manually unlock the door. To learn how to use your physical keys, see Section 4.4.
4.6 Locking from the Outdoor Lockly Guard smart lock will automatically lock once your door is closed. You can set the Auto Lock timer or you may opt to disable this feature through the APP. When Auto-lock is disabled, you can quickly lock your door with One-Touch anywhere on the keypad or simply press the . The latchbolt will lock. To lock the deadbolt, lift the handle to fully lock door. One-Touch feature can be activated or deactivated through the App. Go to Settings, then select Touchscreen Locking.
4.7 Rain Mode Like other digital electronic products water can trigger to activate the touchscreen and fingerprint sensor which may cause the batteries to drain. To protect the lock and extend battery life, you can setup your Lockly Guard to enter Rain Mode to shut off keypad and fingerprint reader whenever rain or water is detected. Activate this feature on the LocklyPro app.
4.8 Shine Mode Lockly Guard touchscreen keypad brightness was designed for optimum battery life. However, some users may need to adjust the brightness to their convenience to enter access codes. Swipe your fingers across the keypad to light up to its normal brightness. To adjust brightness, long press the top button for 3 seconds. The touchscreen keypad with automatically return to normal brightness after the screen dimmed. 4.
5.1 Offline Access CodeTM (OAC) The Offline Access CodeTM (OAC) is a unique feature of our smart lock. It allows you to grant access to guests remotely without guests needing to download the app. To use the OAC feature, make sure you download the LocklyPro app for iOS or Android first, and sync your smart lock to your mobile device. OAC can only be issued by the administrative owner of the lock. From there, you can then issue an Offline Access CodeTM within the app.
6.1 Important Notes Auto Lock Feature Your lock can be programmed to auto-lock between 5-300 seconds after the door opening. You can select the timing through the LocklyPro App. If auto-lock is not activated and door is still open, the touchscreen will remain lighted, simply press on the keypad to lock (Only for Latch Lock Body). One-Touch Locking You can always manually do a quick lock by touching anywhere on the touchscreen. Lockly Guard smart lock is shipped with this feature already activated.
7.1 Cleaning Making sure your Lockly Guard is clean is best practice to ensure optimal product use. Follow the DOs and DON’Ts below. DO • Rinse the touchscreen with warm water prior to cleaning. • Use the application of soap with a damp, lukewarm cloth. • Airdry or wipe dry with a soft microfiber cloth to avoid scratches. DON’T • Don’t use abrasives, high alkaline cleaners, or gasoline to clean your lock. • Don’t apply cleaning detergent directly in sunlight or at high temperatures.
FCC Warning: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: 1. L’appareil ne doit pas produire de brouillage; 2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. IC Radiation Exposure Statement This equipment meets the exemption from the routine evaluation limits in section 2.5 of RSS-102.
For digital versions and instructional videos, please visit the following link LocklyPro.com/support © Copyright 2022 Lockly Guard All rights reserved USA Patent NO. US 9,881,146 B2 |USA Patent NO. US 9,853,815 B2 |USA Patent NO. US 9,875,350 B2 | USA Patent NO. US 9,665,706 B2 | USA Patent NO. US 11,010,463 B2 AU Patent NO. 2013403169 | AU Patent NO. 2014391959| AU Patent NO. 2016412123 | UK Patent NO.EP3059689B1| UK Patent NO.