R REV:1.0 ERP 机型:PL35R1UQ-GL-SMT00030A-V1 ERP P/N: 描述:说明书:PL35R1UQ/PGD228W,SMT000,REV.B(UMPGD228W20220830), 140x195mm,80g书纸,双面单黑印刷,18页36面装订本,RoHS2.0,REACH, Prop65,POPs,PAHs K Designer:Sabrina Date:2022-08-30 WWW.LOCKLYPRO.
Table of Contents Section 1 - Product Highlights 1.1 Product Features Section 5 - Advanced Features 1 Section 2 - Product Overview 2.1 Product Overview- Exterior 2 2.2 Product Overview- Interior 3 2.3 Understanding Your New Lock 4 2.4 Reset Button 5 2.5 Rebooting Lockly Guard 5 2.6 Low Battery 6 2.7 Changing the Battery 7 5.
1.1 Product Features Patented Hack-proof PIN Genie Keypad Digits are randomly displayed on the keypad ensuring access codes to be undetectable to intruders after repeated use. Numbers are randomly distributed across 4 buttons, with 3 numbers in each button. Users can press any button showing their number. Location of the numbers are always different everytime someone uses the keypad, making it hard for prying eyes to guess the correct code.
2.1 Product Overview- Exterior Fingerprint Reader Touchscreen Keypad Buttons RFID Card Reader Exterior Handle Key Hole Reboot Button Mirco USB Port Key Hole Cover Battery Indicator OK Button Welcome/ Safe Mode 2 SECTION 2.
2.2 Product Overview - Interior Battery Cover Reset Button Program Button Battery Compartment *Operated by 4 X AA size alkaline batteries ( not included ) Interior Handle Door Sensor SECTION 2.
2.3 Understanding Your New Lock NOTICE The Default Access Code is 123456 After the installation of your new Lockly Guard, understanding some key functions of operating your smart lock is important. The following guides will walk you through resetting a lock, adding and deleting Access Codes, adding and deleting fingerprints, adding and deleting RFID cards and also how to configure your OAC (Offline Access Code™) For any questions you can always visit http://LocklyPro.com/support for assistance.
2.4 Reset Button In order to restore the Lockly Guard to factory default settings, you must have your “Activation Code” available. The Activation Code can be found on the Activation Code Card that came with your smart lock. After you have the Activation Code ready, push the reset button on the back panel of the Lockly Guard to perform your reset. See below to see which Reset Process applies for you. Once the smart lock has been reset, all the data previously stored will be deleted.
2.6 Low Battery When the battery is in seriously low condition, Lockly Guard will make continuous beeping sounds in addition to the flashing low battery icon on the touch screen. You should replace batteries immediately to avoid your smart lock from shutting down. When your smart lock low-battery warning alert finally dies, you will have 3 chances to unlock your smart lock either by a password, APP or fingerprint. If the unlock was successful, the low-battery warning alert will be on for 1 minute.
2.7 Changing the Battery Open the battery compartment cover and insert 4 AA alkaline battery as shown below. • Make sure the batteries are correctly oriented. • Replacement of batteries does not affect programmed data. • Replace only with new batteries. DO NOT mix with used batteries. 2 1 3 AA 1.5V X 4 - + + - + + - NOTICE SECTION 2.7 Whenever batteries are replaced, reconnecting the smart lock to your smartphone App is required. If you have not yet downloaded the app, visit: LocklyPro.
3.1 Configuring Access We recommend pairing your lock to your smart phone to manage your access codes. Section 3.1 - 3.11 refers to locks NOT paired with a smart phone. Once paired with a smart phone, the Program button will be disabled. Your new Lockly Guard Access Code can be any combination of 6 to 8 digits. Once a new Access Code is entered, the Default Access Code of 123456 would be deleted.
3.2 Entering Programming Mode To enter Programming Mode, remove the battery compartment cover on the interior side of the Lockly Guard to expose the Reset and Program buttons. Simply press the Program button to enter programming mode. Program Button Note: Program button will be disabled once synced to a smart phone. Configure all settings via synced smart phone. Access Codes previously added by Programming mode will be cleared. To end Programming Mode, press the Program button anytime.
3.3 Adding an Access Code While in Programming Mode, select “1AD” to add an Access Code. If you are not in Programming Mode, please see Section 3.2 to enter Programming Mode. After pressing “1AD” press “Pd” to add an Access Code. Enter your new 6 - 8 digit Access Code and press when you are finished. You will then re-enter the code to confirm your new Access Code. Remember, just touch the digit you need within the circle around each 3 numbers. There is no need to touch the exact location of the number.
3.4 Deleting an Access Code While in Programming Mode, select “2DE” to delete an Access Code. If you are not in Programming Mode, please see Section 3.2 to enter Programming Mode. After pressing “2DE” press “Pd” to delete an Access Code. Example Only Active Access Codes will then be displayed on the screen in sequence from left to right, top to bottom. In the example shown on the right, the Access Code displayed is 135790. Rotate through different Access Codes shown by touching any number on the screen.
3.4 Deleting an Access Code (Continued) There are two incidents where your Access Code cannot be deleted. • There are no Access Codes set. The factory default Access Code cannot be deleted. • There is only one (1) Access Code saved in the smart lock. At least one code must be registered. Please add another Access Code before attempting to delete the existing code. No Access Codes Set Only one Active Access Code 3.
3.6 Adding a Fingerprint We are using an advanced biometric sensor, providing the most secure fingerprint authentication. For security reasons, Lockly Guard will only accept fingerprint patterns that consist of cross intersection points. Patterns with no cross intersection points will not be acceptable. Please check your fingers before registration to make sure the finger you want to register will be acceptable by our system. Otherwise, use an alternative finger to ensure successful registration.
3.6 Adding a Fingerprint (Continued) While in Programming Mode*, select “1AD” to add an Access Code. If you are not in Programming Mode, please see Section 3.2 to enter Programming Mode. After pressing “1AD” press “FP” to register a Fingerprint. Upon pressing “FP”, you will enter Fingerprint Registration Mode and you will see a green LED ring light up on the fingerprint panel on the exterior of Lockly Guard. Once you’re in Fingerprint Registration Mode you will see two numbers displayed on keypad.
3.6 Adding a Fingerprint (Continued) Scan your finger by lightly placing your designated finger on the sensor until you hear a beep. Lift your finger and repeat the process slowly until the digit “6” shown on the screen becomes “1”. If you have successfully scanned and registered your fingerprint, you will hear a long beep, and the Bluetooth icon will flash green. PASS will show on the keypad and press OK to exit. If you did not successfully register your fingerprint, FAIL will show on the keypad.
3.7 Fingerprint Scanning Directions (Continued) Side View Top View OK X X OK Correct X X Incorrect 3.8 Fingerprint Scanning Tips & Troubleshoot Tips for Fingerprint Enrollment and Recognition • Place your finger to completely cover the sensor with maximum contact surface. • Position the center of your finger (core) to the center of the sensor. • Hold your finger still for more than a second until you hear a beep. • Scan a finger that is clean and free from dirt.
3.9 Deleting Stored Fingerprints* While in Programming Mode, select “2DE” to delete a Fingerprint. If you are not in Programming Mode, please see Section 3.2 to enter Programming Mode. After pressing “2DE” to delete, press “FP” to delete a fingerprint. Your registered fingerprint numbers will be displayed on the screen. Tap number to rotate to the next registered fingerprint. When you have found the fingerprint ID you want to delete, press and hold the OK button for 3 seconds to delete.
3.10 Adding an RFID card While in Programming Mode, select “1AD” to add an RFID card. If you are not in Programming Mode, please see Section 3.2 to enter Programming Mode. After pressing “1AD” press "Id" to add an RFID card. Place the RFID card to the screen where the RFID card sensor is embedded. 18 PASS will show on the keypad once card is registered successfully. SECTION 3.
3.11 Deleting RFID Card While in Programming Mode, select “2DE” to delete an RFID card. If you are not in Programming Mode, please see Section 3.2 to enter Programming Mode. After pressing “2DE” press “Id” to add an RFID card. Your registered RFID card will be displayed on the screen. Tap the screen to show the next registered RFID. When you have found the RFID card you want to delete, press and hold the OK button for 3 seconds to delete.
4.1 Unlocking with Access Codes Lockly Guard Smart Lock can be unlocked using multiple ways - via your stored Access Code, registered fingerprint, smartphone with Bluetooth, or the physical key supplied with your lock. Slide your hand across the screen to activate the keypad. Enter your 6 to 8 digit Access Code followed by the . Press OK anytime to reset if you entered the wrong digit. OK Button If the Access Code entered is correct, the door will unlock.
4.2 Unlocking/Locking with Fingerprints Unlocking Place a registered finger to the fingerprint scanner located on the exterior handle of the lock. To register a fingerprint, please see Section 3.6. OK Button If your fingerprint is registered and acknowledged, you will hear a “beep” sound and a Green LED will light up on the fingerprint scanner. You can then push down the handle and open the door. If you see a Red LED, it means your fingerprint is not recognized.
4.3 Locking/Unlocking with App You must have the LocklyPro iOS or Android app installed in order to lock and unlock with smartphone. Please download the app by visiting the link below or search "LocklyPro" from the correct app store. O PR Scan or visit LocklyPro.com/app 4.4 Unlocking with RFID Push down the handle and open the door after it chimed. Light up the screen by touching the keypad. 22 Place your RFID card closer to the panel. SECTION 4.3 ~ 4.
4.5 Locking/Unlocking with Physical Key Exterior View Push to Open Rotate to Access 1 Push 2 3 Pull Rotate To unlock your Lockly Guard using the physical key (supplied), open the key cover below the exterior handle by pushing the top part of the cover to reveal the keyhole. Insert your key and turn clockwise or counter clockwise to lock or unlock the door. SECTION 4.
4.6 Safe Mode Lockly Guard will enter Safe Mode when three (3) consecutive wrong Access Codes are entered within 5 minutes. When in Safe Mode, the lock status icon will start to flash. To disable Safe Mode, you must unlock the door using the correct fingerprint or enter the correct Access Code twice in a row. Activate the keypad by pressing and holding for 3 seconds. Once the screen is activated, enter the correct Access Code carefully twice, pressing after every time.
4.6 Safe Mode ( Continued ) There are four (4) ways to disable Safe Mode. Option 1 - Entering Correct Access Code Activate the keypad by pressing and holding for 3 seconds then enter the correct Access Code twice (2) when the keypad is available, pressing after every time the Access Code is entered. Option 2 - LocklyPro App Use the app that is synced to your Lockly Guard to disable Safe Mode by unlocking the door.
4.7 Locking from the Outdoor Lockly Guard smart lock will automatically lock once your door is closed. You can set the Auto Lock timer or you may opt to disable this feature through the APP. When Auto-lock is disabled, you can quickly lock your door with One-Touch anywhere on the keypad or simply press the . For Swing Edition (228SW) only the latchbolt will lock. To lock the deadbolt, lift the handle to fully lock the door. For Slide Edition (228SL) One-Touch Locking feature will fully lock the door.
4.8 Rain Mode Like other digital electronic products water can trigger to activate the touchscreen and fingerprint sensor which may cause the batteries to drain. To protect the lock and extend battery life, you can setup your Lockly Guard to enter Rain Mode to shut off keypad and fingerprint reader whenever rain or water is detected. Activate this feature on the LocklyPro app.
4.9 Shine Mode Lockly Guard touchscreen keypad brightness was designed for optimum battery life. However, some users may need to adjust the brightness to their convenience to enter access codes. Swipe your fingers across the keypad to light up to its normal brightness. To adjust brightness, long press the top button for 3 seconds. The touchscreen keypad with automatically return to normal brightness after the screen dimmed. 4.
5.1 Offline Access CodeTM (OAC) The Offline Access CodeTM (OAC) is a unique feature of our smart lock. It allows you to grant access to guests remotely without guests needing to download the app. To use the OAC feature, make sure you download the LocklyPro app for iOS or Android first, and sync your smart lock to your mobile device. OAC can only be issued by the administrative owner of the lock. From there, you can then issue an Offline Access CodeTM within the app.
6.1 Important Notes Auto Lock Feature Your lock can be programmed to auto-lock between 5-300 seconds after the door opening. You can select the timing through the LocklyPro App. If auto-lock is not activated and door is still unlock, the touchscreen will remain lighted. Simply press the on the keypad to lock. One-Touch Locking You can always manually do a quick lock by touching anywhere on the touchscreen. Lockly Guard smart lock is shipped with this feature already activated.
7.1 Cleaning Making sure your Lockly Guard is clean is best practice to ensure optimal product use. Follow the DOs and DON’Ts below. DO • Rinse the touchscreen with warm water prior to cleaning. • Use the application of soap with a damp, lukewarm cloth. • Airdry or wipe dry with a soft microfiber cloth to avoid scratches. DON’T • Don’t use abrasives, high alkaline cleaners, or gasoline to clean your lock. • Don’t apply cleaning detergent directly in sunlight or at high temperatures.
FCC Warning: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: 1. L’appareil ne doit pas produire de brouillage; 2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. IC Radiation Exposure Statement This equipment meets the exemption from the routine evaluation limits in section 2.5 of RSS-102.
For digital versions and instructional videos, please visit the following link: LocklyPro.com/support © Copyright 2022 Lockly Guard All rights reserved USA Patent NO. US 9,881,146 B2 | USA Patent NO. US 9,853,815 B2 |USA Patent NO. US 9,875,350 B2 | USA Patent NO. US 9,665,706 B2 | USA Patent NO. US 11,010,463 B2 | AU Patent NO. 2013403169 | AU Patent NO. 2014391959 | AU Patent NO. 2016412123 | UK Patent NO.EP3059689B1 | UK Patent NO.