User's Manual

R
PLA3543Q/PGA381 STM000,REV.B,300x100mm 80G
, ROHS2.0,REACH,POPs,PAHS,PROP65,
ERP PLA3543Q-GL-SMT00030A-V1 ERP P/N:
REV 0.1
K
É×ÎÛÔÛÍÍ ÝØ×ÓÛ øÐÙßíèï÷
Installation & User Manual
Lockly Guard Wireless Chime is based on bidirectional RF433.92MHz and
Lockly 2.0 proprietary encryption, providing communication reliability,
stability, and better security. It is powered by 3 x AA batteries and supports
5V DC for sustained power supply.
Power Up to Pair the Chime
Open the battery compartment and insert 3 x AA batteries ensuring that they
are correctly oriented. You may also use the included 5V 1A DC adapter to
connect to power supply. Turn the power switch button on the rear side and
the chime will be activated.
NOTE: Wireless Chime will first use the batteries if you have installed 3 x AA
and DC power supply as backup. For a longer product life, it is recommen-
ded to use DC power supply.
Enter the smart door lock into pairing mode. (Refer to the manual of the
smart door lock on how to enter pairing mode.) Briefly press the settings key
at the back of the chime twice (2x). The chime enters the pairing mode. The
red and white LED indicators flashes alternately and slowly. If pairing is
successful, the white LED will be ON for 2S. The red LED will be ON for 2S if the
pairing fails or timeout in 30s.
Power Switch
DC adaptor
(included)
USB cable
Volume Switch
Installation
Mount
Settings Key
5V DC Plug
Settings Key
Power Switch
OFF
ON
Í»¬¬·²¹ Õ»§
Set Ringtone
You will automatically exit the settings mode after 30s if no
action received.
Short press the settings key Play the currently set ringtone
Short press the settings key Switch to the next song
Double tap the settings key Switch to previous song
Press and hold the settings key Save and exit settings
When the alarm is triggered, the chime will ring and the
alarm will last for 3 minutes. Briefly press the settings key at
the back of the chime to turn off the alarm.
WWW.LOCKLYPRO.COM
High
Low
Press the doorbell button on the door lock. The wireless chime will ring and
the white LED indicator will flash. Use volume switch (on the left side) to
adjust volume to either High or Low.
Install the Wireless Chime
Volume Switch
Low Battery Reminder
When the battery power is too low, the red LED indicator will flash. Please
replace the batteries in time.
Restore to Factory settings
Long press the settings key for 5S, the white LED indicator will be on for 2S,
and the chime will return to factory settings.
After restoring to factory settings, the ringtone will return to the default "Ding
Dong" sound. The pairing information with the smart door lock will be cleared.
WARNING: This product can expose you to chemicals including
Lead, which is known to the State of California to cause cancer. For
more information go to www.P65Warnings.ca.gov.
FCC Warning:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful interfer-
ence, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
whichthe receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user's authority to
operate the equipment.
FCC Radiation Exposure Statement
The Secure Link Wi-Fi Hub complies with FCC radiation exposure limits set
forth for an uncontrolled environment. It should be installed and operated
with minimum distance 20cm between the radiator & your body.
IC WARNING
This device contains licence-exempt transmitter(s) that comply with
Innovation,Science and Economic Development Canada’s licence-ex-
empt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that
may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent
appareil est conforme aux CNR d’Innovation, Sciences et Développe-
ment économique Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes:
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d’en compromettre le fonctionnement.
IC Radiation Exposure Statement
This equipment meets the exemption from the routine evaluation limits in
section 2.5 of RSS-102. It should be installed and operated with a
minimum distance of 20cm between the radiator and any part of your
body.
Cet équipement est conforme à l'exemption des limites d'évaluation
habituelle de la section 2.5 de la norme RSS-102. Il doit être installé et
utilisé à une distance minimale de 20 cm entre le radiateur et toute partie
de votre corps.