R SECURE PRO INSTALLATION GUIDE DEADBOLT EDITION
Go to LOCKLY.com/installation to watch a video version of this installation guide. OR Download the BILT app in the Apple or Google Play store for step-by-step interactive 3-D walk-through installation instructions.
Welcome! This guide will walk you through step-by-step how to install and get your LOCKLY® Secure Pro up and running. Installation generally takes less than 30 minutes. If you have any questions please reference our online support at: LOCKLY.com/support or call (669) 500-8835 for help.
Preparation To complete the installation you will need: Phillips Screwdriver Flathead Screwdriver Tape measure or ruler Prepare door: remove existing deadbolt or use provided template to bore new holes.
Step 1 ADJUST DEADBOLT AND INSTALL Deadbolt slot must align to the center of the door hole. Adjust as shown if needed. 2-3/4" (70mm) or 2-3/8” (60mm) The deadbolt comes set to 2-3/4" (70mm). Adjust length to 2-3/8” (60mm) if necessary. (wear gloves to protect from possible pinching). B A B Push the crank A to extend the deadbolt B C D Deadbolt comes set at 2-3/4" (70mm).
Step 1 ADJUST DEADBOLT AND INSTALL continued Extend the deadbolt by inserting a flat-head screwdriver into the slot and turning clockwise. Insert the deadbolt into mortise flush with door edge, make sure that the right side is up and the slot is in the vertical position. Secure with 2 K screws.
Step 2 INSTALLING EXTERIOR ASSEMBLY (B) B Adhesive tape Check the exterior assembly (B) alignment to door hole and deadbolt before peeling off film on adhesive strips. M Peel film from adhesive strips and make sure torque blade is in the vertical position with the deadbolt extended. Place assembly and torque blade through the deadbolt slot and guide connection cables through the cross-bore hole under the deadbolt as shown. Complete mounting by aligning and securing until flush to exterior door surface.
Step 3 INSTALLING INTERIOR ASSEMBLY (F) 1: Check interior mounting plate (D) alignment to your door hole before securing with adhesive strips. 2: Align and secure mounting plate with adhesive strips. Guide connection cables through the hole and secure to the lower left notched hole. Remove key when finished G (2X) Leave deadbolt extended 4: Use the key to ensure deadbolt locks and unlocks smoothly (no binding or rubbing).
Step 4 PREPARING DOOR SENSORS FOR INSTALLATION Do not mount (install) door sensors yet. You will install in step 7. About door sensors Door sensors provide real-time door condition status, such as the ability to verify if the door is securely closed. It also sends push notifications to your phone whenever your door opens and enables voice control with Amazon Alexa or Google assistant.
Step 4 continued PREPARING DOOR SENSORS FOR INSTALLATION When installing the door sensors, make sure the arrow on the wired sensor (P) aligns to the arrow of the sensor magnet (Q) as close as possible. (P) 3/4" (20mm) 2-3/8" (60mm) Foam pad The sensors need to be as close to level as possible. If needed, use the adhesive foam pad(s) to adjust the height of the wired sensor. 2-3/4" (70mm) Right or Left Sensors can be positioned on either left or right side (see page 10).
Step 4 PREPARING DOOR SENSORS FOR INSTALLATION continued The interior assembly comes with the pre-installed wired door sensor setup for a right swing doors with 2 ¾" (70mm) backset*. For left swing doors, re-route the door sensor wire through the side channel. Pull the foam pad then re-insert to secure the wire. Discard the excess part (e) for GRRUV ZLWK ɍ PP EDFNVHW DV shown below: 7ULP H[FHVV SDUW 3 IRU GRRUV ZLWK ɍ (60mm) backset as shown below.
Step 5 INSTALLING THE INTERIOR ASSEMBLY (F) Plug the cable coming through mounting plate (D) into the interior assembly (F) as shown. Tuck cable under eyelet hooks and route to the right on interior assembly (F). Y X Plug X into Y , match red side of plug with red on socket - insert tightly. NOTE: If you need to disconnect the cable, make sure to press the snap tab to release the plug before carefully pulling it out. Do not force, as this may result in damaging the lock.
Step 5 PROG RAM INSTALLING THE INTERIOR ASSEMBLY (F) continued RESE T PROG RAM PROG RESE T Torque Blade RAM RESE T Thumb turn shaft I 2X Align torque blade with thumb turn shaft, make sure both are in the vertical position. Before placing the interior assembly onto the mounting plate, ensure the thumb turn is vertical. Place the interior assembly against the mounting plate and make sure the torque blade is inserted to the thumb turn shaft.
Step 6 INSTALLING BATTERIES 1 2 3 4 PRESS & HOLD 1: With door open and deadbolt fully extended, place ribbon inside compartment and insert 3 batteries only (hold on inserting the 4th) in bottom row (note correct -/+ polarity). 2: Press and HOLD the program button, continue to hold and install the 4th battery. The lock will automatically start self-check (release program button once check starts).
Step 6 INSTALLING BATTERIES 3: Once self-check completes ensure the lock operates smoothly by manually locking and unlocking the door using the thumb turn on the interior assembly. The deadbolt should operate smoothly without any interference or binding. If necessary, repeat step 2 and ensure that (a) the deadbolt was extended and (b) the torque blade was inserted vertically while the deadbolt was extended. 4: Swipe your hand across the touch screen keypad, the lock should close (lock).
Step 7 INSTALLING THE DOORS SENSOR Make sure you have prepared the door sensors for installation, see step 4 LOCK SENSOR (P) Install on the interior side only. If necessary, trim tab from sensor (P) for doors with 2-3/8" (60mm) backset. Clean surface of door and doorframe, remove film from adhesive, attach and secure close to door edge as shown.
Step 7 INSTALLING THE DOORS SENSOR DOOR FRAME SENSOR (Q) Manually retract deadbolt and close door. Dry fit sensor (Q) to door frame and check for alignment. If needed, raise the height of the sensor to be more level with sensor (P) by adding 1 or 2 of the included adhesive foam pads. Once satisfied both sensors are as level as possible, remove film from adhesive and install with arrows aligned to each other with less than a 3/4" gap between each sensor.
Step 8 INSTALLING STRIKE PLATE Use the supplied door strike or use your existing as long as deadbolt operates smoothly without binding or catching. K(2X) L N IMPORTANT: because doors and frames vary in design it may be necessary to make slight adjustments to your strike plate and/or dust box in order to ensure smooth deadbolt operation. This is very important.
Step 9 DOWNLOAD LOCKLY® APP You have completed the LOCKLY physical lock installation. To enable live monitoring and voice control with Google Assistant or Amazon Alexa, you will need to setup the included Secure Link Wi-Fi hub and pair it with the LOCKLY Secure Pro deadbolt smart lock door sensors. Before connecting Secure Link Wi-Fi hub download the LOCKLY app on your smartphone. It’s required to finish setup and to set (pair) the connection between hub and lock. Scan or visit LOCKLY.
Step 10 SETTING UP THE SECURE LINK WI-FI HUB To set up your LOCKLY® Secure Pro, choose an appropriate location for the Secure Link Wi-fi Hub for optimum performance (see below). For optimum connectivity, it is recommended that the hub be no further away from the lock than 30 feet (9 meters) During the setup process position yourself between the lock and the Secure Link Wi-Fi Hub—ideally no more than 30 feet (9 meters) apart.
Step 10 SECURE LINK WI-FI HUB SETUP continued Plug the Secure Link Wi-Fi Hub into the 5V 1A USB AC adapter and plug the AC adapter to your wall socket. A GREEN LED indicator light will flash slowly to indicate that the Wi-Fi Hub is ready to connect. LED Indicator is located next to the Setup Button USA Outlet Shown Once you have confirmed that your Secure Link Wi-Fi Hub is ready to connect to your lock, open the LOCKLY® App from your smartphone.
Step 11 CONNECTING YOUR LOCKLY® SECURE PRO The App will take you through the following steps, make sure the smart lock has been properly installed. You will need your activation card that is included in the box to proceed.
Step 11 9:45 AM 9:47 AM 9:45 AM AT&T 100% 100% AT&T 9:48 AM Plug in your Secure Link and Click "YES" Password setting OK 100% 9:46 AM AT&T Click “Yes” when the green light is on Set Wi-Fi AT&T CONNECTING YOUR LOCKLY® SECURE PRO Confirm lock password Set the Admin Code AT&T continued 100% AT&T 9:46 AM 100% Successfully Added AT&T 100% 9:49 AM 100% Congratulations! Your LOCKLY® Secure Pro is now set up. You may proceed to Add the Door Sensors.
Smart Home Ready VOICE CONTROL Control with Amazon Alexa or Google Assistant. Control and check your door status by using your voice through Amazon Alexa or Google Assistant. Alexa, check if my front door is unlocked? Hey Google, unlock my office door. To setup your lock to work with either voice assistant, download the Amazon Alexa or Google Home App and add a new skill for Amazon Alexa or action for Google Assistant.
FCC Warning: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: 1. L’appareil ne doit pas produire de brouillage; 2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
INSTALLATION OVERVIEW & PARTS LIST Battery Cover F H PM5 x 25mm Screw, Door thickness1-19/50"~1-69/100"(35~43mm) E2 PM5 x 35mm Screw, Door thickness1-69/100"~1-97/100"(43~50mm) NOTE: You can either use M or O to stabilize the exterior part. O requires drilling an extra hole. Use provided Template for drilling instructions if needed.
Connect with us @meetlockly | #LOCKLY
Reference installation parts overview foldout.
R SECURE PRO We’re here to help! help@LOCKLY.com For the latest version of this manual, please visit the link below: http://LOCKLY.