Open-Q 835 µSOM Modular Certification TechNote77 OEM Integrator Guide [Document: ICS-01RND1265-TN-077 Revision: 1.1] NOTICE TO PERSONS RECEIVING THIS DRAWING AND/OR TECHNICAL INFORMATION INTRINSYC Technologies Corp. claims proprietary rights to the material disclosed hereon.
Open-Q 835 µSOM Modular Certification TechNote77 OEM Integrator Guide Rev. 1.1 Identification Document Title Open-Q 835 µSOM Modular Certification TechNote77 OEM Integrator Guide Document Number ICS-01RND1265-TN-077 Version 1.1 Date September 19, 2019 History REVISION DATE DESCRIPTION PAGES 0.1 Sept 6, 2019 Original Document All 0.2 Sept 9, 2019 Incorporated changes after initial document review: Changed references and name of document from Open-QTM 835uSOM to Open-QTM 835μSOM. All 1.
Open-Q 835 µSOM Modular Certification TechNote77 OEM Integrator Guide Rev. 1.1 Table of Contents 1. INTRODUCTION...................................................................................3 2. APPLICABLE MODULE .......................................................................3 3. ADDITIONAL REGULATORY CONFORMANCE TESTING AND/OR SUBMISSIONS REQUIRED BY THE INTEGRATOR .....................................3 4. COMPLIANT/ALLOWABLE TX POWER SETTINGS ..........................3 5.
Open-Q 835 µSOM Modular Certification TechNote77 OEM Integrator Guide Rev. 1.1 1. INTRODUCTION This document describes the steps that the OEM integrator must follow when designing and manufacturing a system utilizing the Open-Q 835 μSOM Transmitter Module. Failing to follow the instructions in this document may invalidate the FCC and IC (Industry Canada) certifications and authorizations of the Module for use in the U.S. and Canada.
Open-Q 835 µSOM Modular Certification TechNote77 OEM Integrator Guide Rev. 1.1 5. ALLOWABLE ANTENNAS TO USE WITH THE RADIO MODULE The module is certified for use with certain antennas as described in this section. Allowed Antenna Types: 1. Dipole antenna Table 1 Allowed Maximum Gain (dBi) Dipole, Including Cable Loss 2.4~2.5GHz 3.32 4.9~5.8GHz 6.11 The required antenna impedance is 50 ohms.
Open-Q 835 µSOM Modular Certification TechNote77 OEM Integrator Guide Rev. 1.1 6. ANTENNA PLACEMENT AND RF SAFETY The FCC and other countries’ regulatory bodies impose strict conditions and limitations on the RF exposure levels of end products. Acceptable RF exposure levels for this Module depend on transmit power, the location of the transmitting antenna(s) inside the host system and the expected separation of the transmitting antennas to the end user.
Open-Q 835 µSOM Modular Certification TechNote77 OEM Integrator Guide Rev. 1.1 7. SIMULTANEOUS TRANSMISSION WITH OTHER INTEGRATED OR PLUG-IN RADIOS The FCC and IC impose conditions and limitations when additional radio(s) are co-located in the same host system as the Module with capability to transmit simultaneously.
Open-Q 835 µSOM Modular Certification TechNote77 OEM Integrator Guide Rev. 1.1 The FCC requires a logo signifying emission compliance on the outside of the host system. The OEM integrator is responsible to perform FCC Part 15 Class B digital emissions testing on the end system with the radio Module installed. The FCC logo below should not be affixed unless the OEM integrator has obtained the necessary Part 15 approval, e.g., selfdeclaration of conformity.
Open-Q 835 µSOM Modular Certification TechNote77 OEM Integrator Guide Rev. 1.1 10. REQUIRED LABELING ON THE MODULE 10.1 FCC and Industry Canada Labelling on the Module The OEM integrator must ensure that the FCC ID and IC number is affixed on the Module or in a User/Installation Manual along with other country certification numbers and logos as described herein. Note: the original Module manufacturer may affix regulatory labeling at time of Module manufacturing.
Open-Q 835 µSOM Modular Certification TechNote77 OEM Integrator Guide Rev. 1.1 subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Open-Q 835 µSOM Modular Certification TechNote77 OEM Integrator Guide Rev. 1.1 11.2 Industry Canada Requirements for End User Manual / Installation Manual Industry Canada Statements This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Open-Q 835 µSOM Modular Certification TechNote77 OEM Integrator Guide Rev. 1.1 (iv) De plus, les utilisateurs devraient aussi être avisês que les utilisateurs de radars de haute puissance sont dêsignês utilisateurs principaux (c.-à-d., qu'ils ont la prioritè) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
Open-Q 835 µSOM Modular Certification TechNote77 OEM Integrator Guide Rev. 1.1 circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization. Note Importante: Dans le cas où ces conditions ne peuvent être satisfaites, l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé sur le produit final.
Open-Q 835 µSOM Modular Certification TechNote77 OEM Integrator Guide Rev. 1.1 12. OEM INTEGRATOR CHECKLIST The OEM Integrator will integrate the Module in the host systems in accordance with the instruction specified in this document and the documents referenced herein. The OEM Integrator will ensure the Module is integrated in a host system using only antennas that are of the same type and having equal or less antenna gain as described in this document.
