Manual

ManualsBrandsLivorsi ManualsSensorsTTK1050EL

Trim Tab Installation with Electronic Sensors

Model Number: TTK1050EL, TTK850EL, TTK750EL

1 of 11

715 Center Street Grayslake IL 60030 P: 847.752.2700 E: info@livorsi.com www.livorsi.com

REV B MAY 2015 TTK EL Models

Parts Included

(2) Trim Tabs with Sensors

(2) Hydraulic Pumps

(2) Mounting Templates

Harnesses - TTMWH & (2) - CBIWH

Mounting Hardware

Stainless steel hoses sold separately- 4 hoses required per kit

Mounting Tab Location

Available mounting area:

Before selecting a mounting location verify proper clearances inside (transom mounted compo-

nents, etc) and outside (turning drive and propeller clearance) of the boat. Do not mount tabs

in the chine area.

NOTE: The farther the tabs are between each other the better, this will allow you to achieve

the maximum performance out of your tabs.

Summary of content (11 pages)

PAGE 1
Trim Tab Installation with Electronic Sensors Model Number: TTK1050EL, TTK850EL, TTK750EL Parts Included (2) Trim Tabs with Sensors (2) Hydraulic Pumps (2) Mounting Templates Harnesses - TTMWH & (2) - CBIWH Mounting Hardware Stainless steel hoses sold separately- 4 hoses required per kit Mounting Tab Location Available mounting area: Before selecting a mounting location verify proper clearances inside (transom mounted components, etc) and outside (turning drive and propeller clearance) of the boat.
PAGE 2
Billet Trim Tab Installation Mounting tab location cont. Transition of the hull to tabs: Recommended Transtion: Allows tab to be removed fully from the water flow underneath the boat while under way. Some applications may require the tab to be mounted even higher to be out of the water flow. 715 Center Street Grayslake IL 60030 P: 847.752.2700 E: info@livorsi.com www.livorsi.
PAGE 3
Billet Trim Tab Installation Using the template: Once the location is determined, use the supplied template for drilling holes. The template will need to be printed on 11”x17” paper (minimum), template scale is 1:1. When printing make sure your print settings do not resize the document, keep it at 100% or disable any scale options.
PAGE 4
Billet Trim Tab Installation Mount the tab: If the Livorsi Trim Tabs are replacing existing tabs, make sure to seal any unnecessary holes on the transom. Use a high quality marine sealer suitable for underwater use. Recommended sealant: Marine Grade RTV / silicone sealant 4200 or 5200. Use this same sealer and apply liberally around each fastener, indicator wires and between transom and upper trim plate. It is recommended to apply the same sealant to the inside of the boat.
PAGE 5
Billet Trim Tab Installation Sensor wires DOWN UP UP DOWN Back view of mounting plate 715 Center Street Grayslake IL 60030 P: 847.752.2700 E: info@livorsi.com www.livorsi.
PAGE 6
Billet Trim Tab Installation Electric connections: The Livorsi trim tabs include leads to connect to the supply power. It is recommended to install an auto reset 40 Amp breaker on the main hydraulic pump 12V supply. The pump boat harness (20ft) has three leads with eyelets- Green, Blue and Red. These run to your trim switches. 715 Center Street Grayslake IL 60030 P: 847.752.2700 E: info@livorsi.com www.livorsi.
PAGE 7
Billet Trim Tab Installation Sensor Wiring The sensor wire leads that were fished thru the transom will need to be inserted in to the 6 pin Deutsch connector and secured with a wedge lock. Below is the pin out. Pin Number 1 2 3 4 5 6 connector wedge lock Wire Color Red White Blue Black Green Tan Description PPS1 (5V) PPS2 (5V) PPS1 Signal PPS1 Ground PPS2 Ground PPS2 Signal sensor wires from trim tab Once pins are pushed thru the connector, insert the wedge lock to secure pins.
PAGE 8
Billet Trim Tab Installation LED Indicator will have to be calibrated to trim tabs Connections directly to LED Indicator 715 Center Street Grayslake IL 60030 P: 847.752.2700 E: info@livorsi.com www.livorsi.
PAGE 9
Billet Trim Tab Installation VeseelView® will have to be calibrated to trim tabs Connections to a Mercury VesselView® 715 Center Street Grayslake IL 60030 P: 847.752.2700 E: info@livorsi.com www.livorsi.
PAGE 10
Billet Trim Tab Installation Fill the pump with oil: The pump reservoir has markers indicating the maximum and minimum oil levels. The operating temperature and the oil used will determine the reaction speed of the tabs. MAX MIN Types of Oil ATF Reaction Time FASTER 20w20 10w30 SLOWER Testing: The hydraulic system will be full of air, the system is designed to self purge this air when the tabs are raised and lowered.
PAGE 11
Billet Trim Tab Installation Check all hydraulic fittings for leaks 715 Center Street Grayslake IL 60030 P: 847.752.2700 E: info@livorsi.com www.livorsi.