Quick Start Guide

Thank you for purchasing the PTT-M64G.
This Quick Start guide is only applicable to
the PeakPTT PTT-M64G. Please read this Quick
Start Guide for optimal use.
PTT-M64G
Quick Start Guide
ADDITIONAL INFORMATION
Avoid Installing the radio where it will be exposed
to direct sunlight.
Keep the radio free and clear of irrelevant articles
to allow for optimal heat dissipation.
Do not expose the radio to corrosive agents,
solutions or
solutions or water.
PTT USE
The PTT-M64G is pre-configured and set-up for
PTT service once the device has been installed,
connected to power and turned on.
For additional support, please contact PeakPTT
[e-mail].
PT
PTT-M64G CLEANING
Use a clean and dry lint-free cloth to remove dust
and other fine particles from the radio.
Use an alcohol-free screen cleaner to clean the
screen, control knobs, LCD and jacks.
Do not use chemicals like stain removers, alcohol
sprays or oil based solutions on the radio.
Ensu
Ensure the radio is completely dry before use.
CAUTION: Power off the radio before cleaning.
Radio Operating Temperature: -4°F to 140°F
A. Install the bracket in a location that is
accessible.
B. Connect antenna and power cable to the radio
before attaching to the bracket.
C. Slide the radio into the mounting bracket and
secure it using the supplied locking knobs.
D
D. Install the microphone hanger in an easily
accessible location.
E. Connect the palm microphone into the jack
located on the front panel, attach to hanger.
Be sure to only use 3 amp sized replacement
fuses
Please Read The Following Instructions Before
Installation.
Please check the box for all above parts, before
discarding the packing material. Please contact
PeakPTT Immediately, if any parts are missing or
damaged.
12 Month Limited Manufacturer Warranty
PeakPTT reserves the right to change hardware,
and/or software specifications mentioned in this
operating guide without any prior notice. The
product specifications and information
mentioned here are for reference only.
FCC Warning
15.19 Labeling requirements.
This device complies with part 15 of the FCC rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may
cause undesi
cause undesired operation.
15.21 Information to the user.
Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority
to operate the equipment.
15.105 Information to the user.
Note: This equipment has been tested and found to comply with
the limits
the limits for a class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
gua
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Inc
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet or on a circuit different
from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for
help.
The PTT-M64G Status LED Lights include; Power,
Network, PTT, Wi-Fi, Bluetooth and GPS.
POW ER BUTTON (2)
Solid Green: Power On
No Light: Power Off
NETWORK INDICATOR (a)
Flashing G
Flashing Green: Connected To Network
Flashing Red: Network Connection Lost
PTT INDICATOR (a)
Transmit: Solid Red
Receive: Solid Red
BLUETOOTH (c)
Flashing Orange: BT On, No Device Connected.
S
Steady Yellow/Green: BT device connected.
No Light: BT Off
GPS STATUS (d)
Flashing Orange: Searching For GPS satellites
Solid Yellow-Green: GPS signal acquired
No Light: GPS Off
4b not utilized.
a. b. c. d.
The PTT-M64G is equipped with two microphones.
The palm microphone attaches to the PTT-M64G
at the input jack. (7)
The second microphone is built-in (8), and can be
activated by simply pushing the P1 button and
speaking.
P1: Transmit with Internal Microphone
P2: Display current channel members
P3: Display current device contacts
P4: PTT Home screen
1. Antenna Port
2. Power Port
3. USB Port
4. RS232 Port
5. 3.5mm Audio Port
PeakPTT
Tel:
855-600-6161
E-Mail: [e-mail]
Add: 29021 Ave Sherman STE 103, Valencia, CA 91355
www.peakptt.com
Voltage Requirement: 12-24 VDC
RED W IRE: Constant Power. W HITE W IRE:
Ignition/Accessory. BLACK W IRE: Ground.
Check screw clearances before installing the
radio, to avoid damage to vehicle wiring and
other parts.
Connect antenna and power cord to the radio
before attaching to the bracket. Antenna cables
are labeled - attach to same labels on radio.
Install radio with supplied mounting bracket, to
secure radio to the vehicle.
Install radio in an easily accessible location.
Insure proper spacing in back of radio to
accommodate wiring harness/associated wires.