LipRouter H7 User Manual REV 1.
Table of Contents 1. Hardware Specifications ............................................................................................................... 2 1.1 Packing List......................................................................................................................... 2 1.2 Device Parameters............................................................................................................... 2 1.3 Interface Diagram ........................................................
FCC Warning: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
1. Hardware Specifications 1.1 Packing List Name/Model Package Specification Number of pieces Actual number Remarks Device Carton Packing LipRouter H7 1 1 With Antenna Power Cable Carton Packing Standard 1 1 Power Adapter Carton Packing Standard 1 1 Warranty Card Certificate Carton Packing Nagasoft Customization 1 1 Manual Carton Packing Nagasoft Customization 1 1 1.
Operating Temperature 0℃ - 45℃ Anti-vibration 5.5~200Hz 1.3 Interface Diagram 6 USB ports 1/2/3/4 = WIFI antenna interface (only one antenna used) 5/6 = DC input interface 1、USB interface 2、WAN interface 3、LAN interface 1 4、LAN interface 2 5、LAN interface 3 6、LAN interface 4 7、Power switch 2. Installation and Commissioning 1. 2. 3. 4. 5. Remove the LipRouter from the packaging and place it on a stable desktop.
. 7. 8. 9. After entering the main interface, please click the "Settings" icon button in the lower right corner to enter the setting interface. In the setting interface, click the "Bonding account" button, enter the account / password or scan the QR code to log in, and then you can use the bonding function, as shown in the figure below: In the setting interface, click the "WAN" button, you can set to automatically assign or manually assign an external network IP address.
3. Software Functions 3.1 Boot Interface After the LipRouter is powered on, its 5-inch touch screen control interface is as follows: 1. Bonding network: Real-time monitoring of the network speed of the bonding network, with the function of real-time monitoring of aggregated traffic. 2. Wired network: Real-time monitoring of wired network speed. 3. 4G network: Real-time monitoring of multiple 4G network speeds and traffic, and support bonding 4G network speed and traffic monitoring. 4.
3.3 Account Management Click the "Bonding Account" button in the settings interface to enter the bonding account management interface, as shown in the figure below: In the account management interface, you can log in to the bonding account by entering the account and password, or you can log in by scanning the QR code, as shown in the following figure: After logging in, you can get the type of bonding account and traffic usage information.
In the WIFI management interface, you can customize the WIFI network name and network password. You can operate WIFI to turn it on or off, select 2.4G mode, and select 3 secure connection modes. After the setting is completed, click the “Apply” button in the lower right corner to make the setting take effect. Click button at the bottom to return to the setting interface. 3.
Click “Apply” button for the setting to take effect. Click setting interface. button at the bottom to return to the 3.6 LAN Management Click the "LAN" button on the setting interface to enter the LAN setting interface, as shown in the figure below: Set the LAN connection settings in the LAN setting interface, and set the “IP address” and “Subnet mask” respectively. Click “Apply” button for the settings to take effect. Click button at the bottom to return to the main interface of settings. 3.
to the setting interface. 3.8 Device Information Click the "About" button on the setting interface to enter the device information interface, as shown in the figure below: In the device information interface, you can view the device serial number and software / firmware version information. If there is a new version, there is an upgrade button on the interface to prompt firmware upgrade and software upgrade.
Click “Factory Reset” to pop up the restore factory prompt interface, click “Confirm” to restore the parameters to the original factory state, as shown in the figure below: 10
