09.2020 - 1.100.
Do you have all the tools needed? 1 M5 x 30 PANHEAD SCREWS x 4 WALL ANCHOR x 4 2 7 mm Make sure that you have the correct type of anchors for the wall that you’re mounting the device (i.e: concrete, drywall) Hammer Drill Screwdriver Laser Meter Tape Measure Pencil Bubble Level Tape Template INSTRUCTIONS All instructions here are for Litum Anchor/Gateway Endurance referred to as “Anchor/ Gateway(s)” in the document. CAUTION The anchor/gateway is not suitable for mounting on metal surfaces.
WHERE TO MOUNT 1 The anchor/gateway must be mounted on walls, not on ceilings. CEILING 2 All anchors/gateways must be mounted consistenly to the same height across the facility. CEILING Anchor/Gateway h ideal = 4 m (13 ft) h min = 2.5 m (8 ft) WALL FLOOR If it is required to install the anchor/gateway higher than 4m (13 ft), please consult Litum. FLOOR WHERE TO MOUNT 3 If you need to mount anchor/gateway close to a corner, make sure to stay away at least 50 cm (1.5 ft).
HOW TO MOUNT 1 LOCATE & MARK Print the anchor/gateway drilling template. Use it with bubble level and place it on the wall. 4 INSTALL SCREWS Firmly install all screws until they are pulled flush against the plastic surface of the anchor. All screws must be firmly installed to prevent unwanted movement of the anchor. Ensure the device is securely fastened to the wall. 2 DRILL & INSERT WALL PLUGS Drill the four holes on the template and insert wall plugs.
B PLUG IN You can connect the anchor/ gateway to AC or DC power outlet as shown here. DC 5V DC 12-24V AC 110/220V Make sure to use correct power outlet for your device. Failure to do so might result in explosion. OPERATION When the device is connected to a stable power supply, service LED should start to blink. The service LED will light up and remain steady when the device is communicating with a server. RF Comm LED indicates RF communication is active.
S U ER TT LE Please print the anchor drilling template on US Letter size paper. Please check that the template printout aligns with Litum Anchor/Gateway Endurance screw holes before proceeding.
A4 R PE PA Please print the anchor drilling template on A4 size paper. Please check that the template printout aligns with Litum Anchor/Gateway Endurance screw holes before proceeding.
Version 1.1 Attachment A LITUM LIMITED HARDWARE WARRANTY ........ This Limited Product Warranty (“Warranty”) is an agreement between the buyer (“Buyer”) and Lİtum Bilgi Teknolojileri San. Ve Dıs Tic. A.S (“Seller”) applicable to hardware (“Product”, “Products”) provided by the Seller. 1. Seller warrants the Buyer that the Product will substantially conform to Seller’s then-current published specifications for such Product.
Version 1.1 Attachment A LITUM LIMITED HARDWARE WARRANTY ........ 10. The warranty covers all defects of the Product during the warranty period due to faults in workmanship or material at the shipping date. The warranty is limited to repair and/or replacement and does not include any other obligations including but not limited to incidental or consequential damages. The warranty is not valid if the Product has been misused, installed and/or used contrary to the instruction manual.
06.2021 - 1.2.200.1.1 Product Data Sheet GATEWAY SERIES ® LITUM GATEWAY ENDURANCE Model No. 200 263 mm Litum Gateway Series products are fundamental to the mesh network required to track, monitor and locate staff, equipment and assets. Litum Anchor Endurance is specifically engineered for optimum performance in rough environments with a robust design. 76 mm Litum RTLS system allows gateways to work together seamlessly with anchors to collect and transfer high accuracy location information.
FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
IC Warning This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.