28-Aug-2019 V0.
RYORR2L RYORR2L Version Modified content Date V0.9 [1] RYORR2L User Guide 20190218 V0.91 [1] Support sending more AT commands simultaneously. 20190417 [1] Add Command “AT+RST”, to reset software [2] Add Command “AT+LED:”, to turn on/off red/greenLED. [3] Add Command “AT+BUZON:”, to set the turn-ontimingof buzzer. [4] Add Command “AT+BUZ:”, to turn on/offbuzzer. [5] Add Command “AT+SCAN:”, to turn on scanning function. [6] Use UART interface to update FW.
RYORR2L SOFTWARE INSTALLATION [1] SecureCRTPortable download link[link1] [2] QCOM download link [link2] FW UPDATE 1. Open QCOM。 COM Port: COM3 (Device Manager→COM Port (COM and LPT) to check COM Port number. Here we take COM3 for example.) baudrate:115200 2. Open COM Port，enter “AT+IAP”；Press “Send Command” and will show below information. Copyright © 2019, REYAX TECHNOLOGY CO., LTD.
RYORR2L 3. Close COM Port. 4. Unzipped SecureCRSecureFXPortable64.rar. 5. Execute SecureCRTPortable.exe. 6. Establish COM Port connection. Protocol: Serial Port: COM3(Device Manager→Com Port (COM and LPT) to check COM PORT number. Here we take COM3 for example.) Baud rate :115200 RTS/CTS: Do not tick. Copyright © 2019, REYAX TECHNOLOGY CO., LTD.
RYORR2L 7. Set Ymodem Package size：Choose “1024 byte”. 8. When the module sends “C” continuously, it means the module is inYmodem mode. (As shown in the screenshot below) Copyright © 2019, REYAX TECHNOLOGY CO., LTD.
RYORR2L 9. Click Transmit→ Send Ymodem→ Choose updated FW file(.bin)→ Press“add”→ Press “Confirm” 10. If show below information, it means “updated completed”. Close the COM Port. Copyright © 2019, REYAX TECHNOLOGY CO., LTD.
RYORR2L 11. Open QCOM. Enter “AT+VER” to check whether the version is correct or not. Copyright © 2019, REYAX TECHNOLOGY CO., LTD.
RYORR2L AT COMMAND [1] Default: Key in “enter” or “\r\n” (0x0D 0x0A) at the end of all AT Commands. Add “? ”at the end of the commands to ask the current setting value. 1. AT to test if the module responds Syntax Response AT +OK 2. Ask the version of the module Syntax Response AT+VER? +VER:[LITEON-002.xxxx.xx] 3. Send more commands simultaneously Syntax Response AT+:+:….. Example: Ask the version, turn on the LED1 and buzzer simultaneously. +VER:[LITEON-002.
RYORR2L 6. Set the time which buzzer remains turning on. Syntax Response +BUZ: AT+BUZON: a 4 bytes seconds (ms). Example: Turn on Buzzer for 1.5secondsand then turn off. +BUZ:1500 AT+BUZON:1500 7. Set buzzer on/off Syntax Response AT+BUZ: +BUZ: value: 0~1 BIT value “0” means buzzer is turned off. BIT value “1” means buzzer is turned on.。 BIT7~BIT1 X BIT0 buzzer Example: Turn on the buzzer. AT+BUZ:1 8.
RYORR2L 9. Update FW through UART interface Syntax AT+IAP 回覆 +IAP ========================= ========================= = When the module sends “C” continuously, it means the module is in Ymodem mode. Execute “SecureCRTPortable.exe” to update Firmware. (For update method, please refer to Page 5.) (C) Reyax Inc. = = By Huck = ========================= ========================= CCCC Copyright © 2019, REYAX TECHNOLOGY CO., LTD.
RYORR2L CERTIFICATION INFORMATION Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
RYORR2L This module is intended for OEM integrators only. Per FCC KDB 996369 D03 OEM Manual v01 guidance, the following conditions must be strictly followed when using this certified module: KDB 996369 D03 OEM Manual v01 rule sections: 2.2 List of applicable FCC rules This module has been tested for compliance to FCC Part 15. 2.3 Summarize the specific operational use conditions The module is tested for standalone mobile RF exposure use condition.
RYORR2L 2.8 Label and compliance information The final end product must be labeled in a visible area with the following: “Contains FCC ID: PPQRYORR2L”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. 2.
RYORR2L Industry Canada statement: This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de licence.
RYORR2L This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The transmitter module may not be co-located with any other transmitter or antenna. As long as 1 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.
RYORR2L End Product Labeling The product can be kept as far as possible from the user body or set the device to lower output power if such function is available. The final end product must be labeled in a visible area with the following: “Contains IC:4491A-RYORR2L”. Plaque signalétique du produit final L'appareil peut être conservé aussi loin que possible du corps de l'utilisateur ou que le dispositif est réglé sur la puissance de sortie la plus faible si une telle fonction est disponible.
