User Manual

ManualsBrandsLITE-ON Technology ManualsComputers & Accessories802.11 b/g WLAN Printer Server Module

Manual of WiSoC-based 802.11g/b WLAN Pocket-Sized Print Server Module

Rev. 1.0

Product Description

Pocket-sized 802.11g/b 1-USB 2.0 High-speed-port print server Module

Draft Specifications

A. Hardware

WiSoC

ARM9-based highly-integrated WiSoC (Marvell 88W8510H), operating at

160MHz.

Companion RF transceiver of WiSoC (Marvell 88W8000G)

Flash

(Default) 2Mbytes

SDRAM

(Default) 8Mbytes (2Mbits x 32)

USB Host

Controller

USB 2.0 High-speed PCI-based host controller (NEC µPD720101)

1. Provides standard 5V, 500mA bus power

2. Supports 1.5Mbps (low speed), 12Mbps (full speed), and 480Mbps

(high-speed) data transmission rates. This port automatically detects

the make and model of the USB printer

Antenna

(Default) Internal PIFA antenna x 2

(Reserved) 1 IPEX antenna connector to external SMA antenna

LAN Port

(Optional) 10/100Mbps RJ-45 connector, with 2 LED lights, indicating 10

or 100Mbps network connectivity

Power

(Input) 5V DC, 2A (mini power jack)

LED Lights

Status, WLAN Active, USB Active, 10/100Mbps (on RJ-45 connector)

DIP Switch

Yes (Normal & Diagnostic modes)

PCB board

Type: Double-sided SMT 6-layered PCB

Dimensions: 53.5 x 85 mm

EMI / Radio

Frequency

CE/ETSI, FCC Class B, VCCI Class B, Telec

Others

Reset button

* This product does not support use of USB hubs for daisy-chained connection,

USB-to-Parallel connectors, or USB cable extenders.

** The LAN port is not available due to the target size of the PCB board.

Model name: OkiLAN 410w

Summary of content (8 pages)

PAGE 1
Manual of WiSoC-based 802.11g/b WLAN Pocket-Sized Print Server Module Model name: OkiLAN 410w Rev. 1.0 Product Description Pocket-sized 802.11g/b 1-USB 2.0 High-speed-port print server Module Draft Specifications A. Hardware WiSoC ARM9-based highly-integrated WiSoC (Marvell 88W8510H), operating at 160MHz. RF Companion RF transceiver of WiSoC (Marvell 88W8000G) Flash (Default) 2Mbytes SDRAM (Default) 8Mbytes (2Mbits x 32) USB Host USB 2.
PAGE 2
B. Hardware System Block Diagram Internal PIFA Antenna 802.11g(b) WLAN RF Transceiver (Marvell 88W8000G) & Other RF Components Flash (2Mbytes) WiSoC (Marvell ARM9-based 88W8510) 10/100M USB 2.
PAGE 3
C. Connect 802.11 b/g Printer Server Module with Printer Mainboard 1) Connect 802.11 b/g printer server module with printer mainboard via USB 2.0 cable with Type A connectors on both sides.
PAGE 4
802.11g(b) Wireless Standard Complies with IEEE 802.11g and 802.11b standard Radio Frequency 2.4GHz ISM Band Radio Frequency Band 2400 - 2483.5 MHz (U. S., Canada ; Channel 1 ~ 11) 2400 – 2483.5 MHz (Europe ; Channel 1 ~ 13) 2400 – 2497 MHz (Japan; 802.11b: Channel 1 ~ 14; 802.11g: Channel 1 ~ 13) Media Access Control Method Carrier Sense Multiple Access / Collision Avoidance (CSMA/CA), with ACK Modulation Types 802.11g: OFDM (64QAM, 16QAM, QPSK, BPSK) 802.11b: CCK (11 & 5.
PAGE 5
Network Protocol Support TCP/IP, IPX, NetBEUI, AppleTalk, LPR, RAW TCP Port 9100 Internet Printing Protocol (IPP) Support Yes Windows Print Monitor Technology Yes DHCP (client) Support Yes Management Interfaces 1. Web Interface 2.
PAGE 6
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 7
This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna, 3) For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change.
PAGE 8
Canadian Regulatory Wireless Notice This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device IMPORTANT NOTE: IC Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.