Mongoose AMGEN Alarm System User instructions Introduction The Mongoose AMGEN alarm is a microprocessor controlled alarm system designed to help protect a vehicle and its contents from being stolen. When armed, the alarm system will trigger if it senses vehicle entry via doors, boot or bonnet or detects movement via an optional shock or movement sensor. The system provides many advanced convenience features and functions to make the system easy to both install and use.
Normal Operation Arming the Alarm System To manually arm the alarm system and set the immobilizer, turn off the ignition, exit the vehicle and ensure all doors (and boot/bonnet) are properly closed, then press button 1 on your transmitter. The siren will chirp and the hazards will flash once to confirm that the alarm has been armed and the LED will start to flash, If the alarm is connected to your central door locking the doors will be lock at this point.
Two Stage Disarm To disarm the alarm system, press button 1. If the alarm system has been triggered, pressing button 1 should stop the alarm cycle but the alarm system will remain armed and the doors will remain locked. If the action causing the alarm trigger is not over i.e the door opening triggered the alarm and the door is still open, then it will require two presses of button 1 to stop the alarm cycle. The alarm will remain armed with the doors locked.
Panic Mode This system also includes a panic mode, which enables you to activate the alarm from the transmitter. This is an especially useful feature should you wish to ward off unwanted attention. The panic facility works regardless of whether the ignition is switched on or off. . If you want to trigger the alarm system, press and hold button 1 for 3 seconds. The panic facility will sound the siren and flash the indicators without immobilizing the vehicle, enabling you to drive away.
Emergency Disarm This facility is provided to allow the system to be disarmed in an emergency if the transmitter batteries have failed or you have lost your transmitter. When the vehicle is entered using the key, the alarm will trigger and the immobilizer will remain armed. To disarm the alarm and immobilizer proceed as follows 'a) If you have not entered a PIN number, turn on the ignition, press the override button once and turn off the ignition.
c) Zone Identification When the alarm system is disarmed, the LED will flash in a sequence to indicate the sensor or switch that triggered the alarm system. This sequence will repeat for three complete sequences of the code after the ignition is switched on.
Control Summary FUNCTION Button 1 Button 2 Conditions Arm (Lack) . Ign OFF Arm (Lock) * Ign OFF Without Sensors Lock . Ign ON Sitter Arm 2m . 1" Ign OFF Silent Arm ae2™ oi ign OFF Without Sensors Disarm (Unlock) . ign OFF Unlock : . ign ON Silent Disarm «2m ol Ign OFF Panic Mode *3s ign OFF Auxiliary Output *3s Ign OFF Valet Mode . 3s 3s ign ON KEY .
Turn Ignition to ON Position l Enter digit | of your PIN code {Press the override button the same number of times as the first digit of your pin code) 1 Cycle the ignition to OFF and then to ON. 1 Enter digit 2 of your PIN code (Press the override button the same number of times as the second digit of your PIN code) Cycle the ignition to OFF and then to ON. The system will give a double chirp to confirm it has entered learn mode. Press button | on your new transmitter .
The basic procedure is the same regardless of no PIN code, single digit pin code or two digit pin code. If the system has no PIN code, press the override button once in block 2 in place of the first digit of PIN number and skip blocks 3 and 4. If the system has a single digit PIN code, follow blocks 1-2 but skip blocks 3 and 4. If the system has a two digit PIN code the follow then entire procedure. . Software Switches The Mongoose AMGEN has a number of software delectable features.
Tum Ignition On MC Enter First Digit of PIN Number u Tum Ignition OFF and then ON ML Enter Second Digit of PIN Number nN Turn Ignition OFF and then ON EB Press Button 1 on Any Valid Transmitter or button 1 of a new transmitter to teach it to the system iB Turn the (animation OFF and ON 5 Enter the first digit of the software switch you wish to change by pressing the Access switch 9 Press Access Switch Once to Change -Passive Arm/Disarm -Horn/Pager Lack On Lute Rearm Lock With Ignition Key -Siren Chirp ON/OF
Mongoose AMGEN Alarm System Installation Instructions Introduction The Mongoose AMGEN alarm is a microprocessor controlled alarm system designed to help protect a vehicle and its contents from being stolen. When armed, the alarm system will trigger if it senses vehicle entry via doors, boot or bonnet or detects movement via an optional shock or movement sensor. The system provides many advanced convenience features and functions to make the system easy to both install and use.
Parts List Mongoose AMGEN Electronics Module Main Wiring Harness 2 x 12 Volt transmitters Immobilizer Wiring Harness LED with wiring harness Access Switch with wiring harness Dual Stage Shock Sensor Part Bag including cable ties, pin switch, screws and bullet connector Mounting Locations Position the electronics module inside the passenger compartment, away from any potential sources of damp or excessive heat.
« One immobilizer circuit either Starter Motor (preferably the starter motor relay if available) Fuel Pump Feed Ignition Coil (if available) Diesel Shut of valve Note : We advise that ECU immobilization is not attempted Main C . RED BLACK ORANGE BLACK/WHITE BLACK/GREEN BROWN GRAY GREEN YELLOW Connect the cable to a permanent 12 volt battery feed (+30) Connect to a good vehicle earth bolt (-31) Connect to an ignition switched supply.
iy The alarm system has the facility to sense signals on door -, door + and Bonnet wires. Therefore the connection points listed above are the recommended configuration but these three wires can be connected in any configuration to make the system as easy to install as possible. ii} If you choose to use the GRAY wire to sense both the bonnet and the trunk, two diodes should be used to prevent interference between the bonnet switch and the trunk light.
BLACK (x2) BROWN/WHITE BROWN/BLACK The two black wires, which exit the electronic module on the left side (via the two pin connector), come directly from the internal embolism relay. Locate the feed wires for the circuit you wish to immobilize, cut the wire and test that the engine does not either start or run. Take care with vehicles with catalytic converters to ensure that unburden fuel can’t damage the converter.
Door Locking S Using SDL Module ( ive P This central door locking system is common on European and Japanese vehicles and many after market central door locking kits which include both motors and a central door locking relay. Locate the COL module which controls the door lack solenoids or the wiring as it exits the drivers or passenger doors into the kick panels. Locate the vehicle lock wire and connect the GREY/RED from the alarm system.
2 Door Locking S Using COL Module (Positive Switch a) Locate the CDL module which controls the door solenoids or the central door locking wiring as it comes out of the drivers or passenger door into the kick panel. Locate the Lock wire and connect the GREY/RED from the alarm system to this wire. Locate the Unlock wire and connect the BLUE/RED from the alarm system to this wire. Join the RED/YELLOW and the RED/BLACK from the alarm system and connect them bath to a permanent feed.
, installation This type of locking can be achieved by adding after market central door locking solenoids in each door. The central door locking in this situation can only be operated by the alarm remote control and not by the ignition key in the door lock cylinders. If an after market central door locking relay is included then follow the instructions for negative pulse locking. a) Join the GREY/YELLOW and the BLUE/YELLOW together and connect to a good earth point.
4. Vacuum Door Locking System This type of locking system is common on German vehicles such as Mercedes, VW and Audi a) Locate the door lock trigger wire that runs from either door to the central docking control system. This will change from 12 volts to earth when the doors are locked and unlocked. b) Cut this wire and connect the BLUE/YELLOW from the alarm system to the cut end which changes voltage when the door locks are activated. [1 Connect the GREY/RED from the alarm system to the other cut end.
Introducing and Removing Transmitters The Mongoose AMGEN can accommodate up to four transmitters. Each time you perform the learn made, the old codes will be deleted therefore, you must teach all transmitters to the system again to ensure that the system continues to respond to all transmitters.
Software Switches The Mongoose AMGEN has a number of software delectable features. These can be changed using the procedure list below. Some of these features are to enable the alarm system to be configured to the vehicle you are installing the system in. Other switch settings will be determined by customer preference and should be discussed with the customer before the installation is completed.
Turn Ignition On . Enter First Digit of PIN Number i. Tum Ignition OFF and then ON .