Normal Operation Arming the Alarm System To manually arm the alarm system and set the immobilizer, turn off the ignition, exit the vehicle and ensure all doors (and boot/bonnet) are properly closed, then press button 1 on your transmitter. The siren will chirp and the hazards will flash once to confirm that the alarm has been armed and the LED will start to flash, If the alarm is connected to your central door locking the doors will be lock at this point.
Valet Mode This is recommended to allow your vehicle to be taken for service or repair, as the setting is remembered even when the battery is disconnected. Disarming the system, turning on the ignition and Pressing and holding both buttons on the transmitter for two seconds enters valet mode. The LED will tum on after two seconds to indicate that the system is in valet mode. The system will remain in this mode until both transmitter button are pressed again for two seconds with the ignition switched on.
Convenience Facilities The LITE-ON VS560 Alarm System has a number of additional convenience feature-: Boot Release/Free Impulsiveness Output The convenience output on the alarm system can be configured for Trunk Release, Free impulse or Latched output depending upon your requirements. Boot Release If your vehicle has a boot release solenoid it can be activated from the transmitter by pressing button 2 for 2 seconds.
Emergency Disarm This facility is provided to allow the system to be disarmed in an emergency if the transmitter batteries have failed or you have lost your transmitter. When the vehicle is entered using the key, the alarm will trigger and the immobilizer will ignition and Passive Arming If selected, this option arms the alarm and set the immobilizer automatically after the ignition has been turned off and a door has been opened and closed.
Control Summary FUNCTION Button 1 Button 2 Conditions Arm (Lock) . Ign OFF Arm (Lock) o Ign OFF Without Sensors Lock . Ign ON Silent Arm . . Ign OFF Silent Arm . »e Ign OFF Without Sensors Disarm (Unlock) . Ign OFF Unlock . Ign ON Silent Disarm . . Ign OFF Panic Mode 2s Ign OFF Car Finder . Ign OFF Auxiliary Output 2s Ign OFF Valet Mode 2s 2s Ign ON KEY .
Introducing and Removing Transmitters Tum the Ignition ON Crass the override switch for 5 seconds until the siren chirps § times and the LED fast flasher twice. ML Press any button on a new transmitter to teach it to the system.
Software Switches The LITE-ON VS580 has a number of software, procedure list below. S re delectable features. These can Software Software Switch Function Default ON OFF Switch Crass Button 1 | Press Button 2 LED ON LED OFF 1 Passive ARM/DISARM Mode OFF ON OFF 2 lan ON Door Lock ON ON OFF 3 Homepage Pager Horn Pager 4 Motor Vacuum Locking 0.58 0.
Tum the Ignition ON and OFF three times within 7 seconds and leave the ignition in the OFF position. NB confirmation that the system is in software switch modification The siren will chirp as made, ML Tum the ignition ON Press the override button once to change switch 1 * Press the override button twice to change switch 2 ¢ Press the override button three times to change switch 3 ete. etc.
ANTENNA WIRE | BLACK VS560 ALARM SYSTEM WIRING DIAGRAM 7 % [ee BLUE ag UNLOCK NC [Tee GREEN ——3 COM PURPLE /WHITE NO — GRAY —y NC WHITE } LOCK CoM PURPLE NO SINGLE STAGE SENSOR SOCKET RED STATUS LED BLUE \ BLACK VALET SWITCH GREY 154 RED BAT (+12V) BLACK ——r GROUND eA BLUE ion (3) GREEN/ WHITE wy.
LITE-ON VS560 Alarm System Installation Instructions Introduction The LITE-ON VS560 alarm is a microprocessor controlled alarm system designed to help protect a vehicle and its contents from being stolen, When system provides many advanced convenience features and functions to make the system easy to both install and use. Transmitter A two button remote control transmitter is used to control the alarm's various features and functions. LITE-ON VE560 system is supplied with two transmitters.
Parts List LITE-ON vS560 Electronics Module Main Wiring Harness 2x12 Volt transmitters CDL Locking Wiring Harness Immobilizer Wiring Harness Arm Wire LED with wiring harness Access Switch with wiring harness Single Stage Shock Sensor (Optional) Part Bag including cable ties, pin switch, screws and bullet connector Mounting Locations Position the electronics module inside the passenger compartment, away from any potential sources of damp or excessive heat.
¢ Bonnet Switch (install if necessary) Good vehicle earth bolt + One immobilizer circuit either :“+ Starter Motor (preferably the starter motor relay if available) <* Fuel Pump Feed “Ignition Coil (if available) % Diesel Shut of valve Note : We advise that ECU immobilization is not attempted Main Connections RED Connect the cable to a permanent 12 vomit battery feed (+30) BLACK Connect to a good vehicle earth bolt (-31) BLUE Connect to an ignition switched supply.
Ensure that the wire you connect to senses all the doors on the vehicle. . Notes : A i) The alarm system has the facility to sense signals on door -, door + and Bonnet wires. Therefore the connection points listed above are the recommended configuration but these three wires can be connected in any configuration to make the system as easy to install as possible.
RED/BLACK The pager output provides a positive signal when the alarm system is triggered and.can be connected to a pager system or a horn relay to drive the original vehicle hom. A software switch is provided to configure this output and details on how to configure this output can be found below. ORANGE (x2) The two orange wires, which exit the electronic module on circuit you wish to immobilize, cut the wire and test that the engine does not either start or run.
Dewar Locking. : : This central door locking system is common on European and Japanese vehicles and many after market central door locking systems which include both motors and a central door locking relay. . a) Locate the COL module which controls the door lock motors or solenoids or the wiring as it exist the drivers or passengers door into the kick panel. b) Locate the vehicle lock wire and connect the WHITE wire from the alarm system.
2 Dose Locking Stem Using co ve Sue a) Locate the CDL. module which controls the door solenoids or the central door locking wiring as it comes out of the driver's or passenger door into the kick panel. . b} Locate the lock wire and connect the WHITE wire from the alarm system. c) Locate the unlock wire and connect the GREEN wire from the alarm system. d) Connect the PURPLE wire (which is already linked to the HEPPLEWHITE) to a permanent feed.
3 installation of new Motors or Gainsaid This type of locking can be achieved by adding an after market central door locking solenoids in each door. The central door locking in this situation can only be operated by the alarm remote control and.not by the ignition key in the door lock cylinders. if an after market central door locking relay is included then follow the instructions for negative purse locking. a) Connect the PURPLE (which is already linked to the PURPLE/WHITE) to a permanent 12 volt source.
This type of locking system is common on German vehicles such as Mercedes, VW and Audi. a) Locate the door lock trigger wire that runs from either door to the central door locking control system. This will change from 12 volts to earth when the doors are locked and unlocked. b} Cut this wire and connect the BLUE from the alarm system to the cut end that changes voltage when the door locks are activated. ©) Connect the WHITE from the alarm system to the other cut end. d) Join the GREEN and the GREY together.
In traducing and Removing Transmitters The LITE-ON VS560 can accommodate up to four transmitters. Each time you perform the meal mode, the oid codes will be deleted therefore, you must teach all transmitters to the system again to ensure that the system continues to respond to all transmitters. To teach transmitters to the system, proceed as follows :Tum the Ignition ON ML Press the override switch for 5 seconds until the siren chirps 5 times and the LED fast flasher twice.
Software Switches The LITE-ON VS560 has a number of software delectable features. These can be changed using the procedure list below. Some of these features are to enable the lama system to be configured to the vehicle you are installing the system in, Other switch settings will be determined by customer preference and should be discussed with the customer before the installation is completed.
mm) Turn the Ignition ON and OFF three times within 7 seconds and leave the ignition in the OFF position. ML The siren will chirp as confirmation that the system is in software switch modification mode. ML Tur the Ignition ON Press the override button once to change switch 1 * Crass the override button twice to change switch 2 * Press the override button three times to change switch 3 ete.