Welcome Thar yeu for choosing the new Datatoal® $4 Alarm system far your motorcycle. The system provides many unique features designed to increase the protection of your machine or lo customize its operation to meet your individual requirements. Some af these features can only be adjusted by your dealer and are dependent on local regulations. For these reasons, we advise you iu discuss the options available with your installing dealer.
Your remote control All 54 systems come supplied with 2 remote controls as standard. iris possible to add up to 4 extra gooier controls (8 in ota. The pictures below show the type of transmitter supplied with your alarm gap ending on the type purchased. The midis picture shows the 54 Red/Green strategist which has been converted for added convenience with a key from the original motorcycle.
Changing your remote control battery Models S4 Red and S4 Green Each remote control contains a single long-life lithium tatter {CR1816}. This battery will normally fast at least 12 months. Normal range for the remote control is around 10 meters. As the battery within the remote central comes to the end of its fife, you will notice a reduction in its range and the battery should be replaced. 1. To replace the battery remove the small screw farm the key ead’ of the cremate and spit the two Halves of the case.
Model 54 Yellow The $4 Yeltsin transmitter contains a single CR2032 Lithium cattery. This battery will normally ast at least 24 months. (See $4 Red and Green for range and its reduction with age]. 1. Use a slam! coin, placed in the caress between the two case haves near the key attachment hole, to split the casings. 2. Lift the circuit board from the rubberized seal. 3. Remove the CR2032 Lithium battery from its holder bating the polarity. 4.
Operating the alarm system This section explains ely how the alarm system works. For a more basic explanation refer to the credit card sized instructions (84 Quick Reference) supplied. We advise you fo carry the quick reference card with you for roadside guidance. Arming the system Passive arming Unless the unit has been placed in ‘winter’ mode, the system will always passive arm 45 secants after the ignition is turned OFF.
Arming the system without the movement sensor ‘Ferry’ Mode). To arm the alarm system but have both the movement and nudge sensors turned off; reds the BLACK bunion within 10 seconds of arming the system with the GREY bunion, The indicators will dash twice 10 indicate the alarm has teen armed and thee indicators will flash three further times lo cunning the movement sensors have been tared OFF.
Disarming the system after it has been triggered if the system has been triggered in your absence, a tong audible tone will be heard when the alarm system is disarmed using the transmitter, The system includes a diagnostic mode, which allows vou to identify the circuit that triggered the alarm system. After the long audible tone, the siren will beep and the LED wilt flash a number of dimes fo indicate what triggered the alarm system.
‘Sleep’ mode All alarm systems use a small amount of current during operation and we advise if the machine is to be left for an extended priced in the armed state, it is left connected to a float charger suitable for maintaining the condition of the battery without damaging 1, such as the Datatool® Battery Conditioner (P1 No, 02012011), However the Datatcol® $id systems include & three revel sleep procedure to reduce the current conscription of the system as the motorcycle battery starts to discharge.
‘Panic/locator’ feature Press and hold the BLACK button of the remote Tor 3 secants vita the ignition switched OFF fo enter ‘translocation’ mode The siren will sand and the indicators will sash until any butter is pressed on the remote central lo um the participant mos off, When triggered, the alarm system: reverts to the logical state held bettors the button was pressed 16 activate the campanile made, Cross and Hood BLACK button for three seconds Winter mode The purpose of this mode is to enable you tn lea
The PIN override system ALL Datatoci® $4 Alarms have 4 PIN disarming feature, As 2 new product there is no PIN number programmed into the alarm, therefore we strongly recommend you enter your awn 4 digit number as one of your first priorities. NOTE: If you do not ante: a FIN number and lose or damage your remote corer whilst oud, you will not. he able to disarm your alarm without accessing your secant remote control.
Entering a new PIN code To initiate the PIN number the following procedure should be followed: N ignition “b ignition aw, ignition sanitation ax, Ignition Bros GREY button Press both buttons LED on bike simultaneous within 10 seconds fins hos rapidity confirmation beep 3 secs ‘for 8 seconds J | ONE LONG TONE Repeat procedure to confirm new PIN To set Toast To set To sot Confirmatory Conform Ta confirm Tocantins firsthand second digit thd dig fourth digit first dig second digit third digit fourth digit beep
Disarming the system with your PIN if the transmitter is lost or damaged, or the transmitter hatter is flat, the system can be overridden by your chosen four digit PIN (Personal Identification Number) used in conjunction with the ignition switch. The PIN procedure can only be used after a full alarm reaction has been initialed, The procedure is as follows: 1.
Adding extra remote controls All systems come wile two remote controls programmed into the alarm unit. Should you require extra or replacement remote contrails they can he purchased through any atatcoi® authorized dealer.
Customizing the system iris possible to change the operation of the security 2. Press the BLACK button an the remote control 0 system 10 suit your requirements {see transmitter move backwards through the labels ta Switch ‘eam procedure for delays on how to enter the (ore beep wiki be heard when the switch is software switches), selected). Nee you have entered the software switch section 3.1 3 seeps are heard you have entered Switch 3 which requires a special engineer's code to enter. 1.
Changing the passive arming settings (passive immobilizer or full passive arming) + Once you have found the passive arming selection {Switch 2), press BOTH buttons of the tamer control to select the switch. A triple beep will be heard confirming you have entered the switch, 2.
Special features @sealer delectable only) Tre following features cin only be accessed by an APPROVED Datatool® dealer. Should you wish to have a settling changed from the factory default please discuss this with our dealer first. The factory default settings have been chosen to deliver the pastime performance from the system. The factory default settings ar in void text NOTE: The inclusion of arm and disarm indication beeps is strictly forbidden in all EU countries. No.
Extending your security Extra siren/Pager output This system contains a supplementary output which becomes positive only when the siren Is sounding. This wire is identified by a green and yellow tag on the end. The position of this wire is detailed on your certificate of installation. This stipulate can be used to drive extra sirens, pagers of telephone dalliers.
Safety notice on the care, handling and disposing of batteries NOTE: The battery used in this device may cause a risk of fire or explosion or chemical burn if mistreated. « Da not short-circuit, charge or heat. « Da not deform, take apart, insert in reverse; observe the + and — markings on {ke battery and equipment, + Do not mix batteries. replace all batteries at the same time with new batteries of same system and manufacture.
Quick Reference Guide Disarm Press GREY button immobilize only Ignition OFF for more than 45 seconds Alarm fully Press GREY button within 45 seconds of ignition OFF ‘Ferry Mode’ Press BLACK button within 10 seconds profaning the alarm fully ‘Panic/Locator’ = With the system armed, press and Hold BLAG button unit! the alarm sounds. To silence, press either button on the remote control Hazards : Press GREY and BLACK buttons together until the hazards start to flash.