User's Manual

TPM-100 (MTPM-100) specification Rev. 6 25

May 2004

TPM-100 (MTPM-100) Product Description

Kit content:

1. 4 Generation 1 Wheel sensors

2. Receiver

3. Display

4. 1 x 17cm Wire Antenna

5. 1 x 2.5 meter antenna

6. Wiring harness

7. Accessories

Optional accessories:

1. 2 x Generation 1, Wheel Sensor Kit for 6 Wheel Vehicles

2. Generation 1 Wheel sensor

3. Valve (in separate items, as specified at “Wheel sensor”)

Wheel sensor:

• Specialized LITEON valve to be purchased from Record. 300-0087810

• Generation I sensor-unit (433.92 MHz)

• Washer 215-0096300

• Slider accessory 200-0028140

The nut that holds the sensor-unit to the valve is fixed with a drop of LOCTITE 243 (Cat No. 18941).

Receiver:

The receiver should fit in a VS350/VS320 housing.

Connectors accessible from the outside:

• SMB connector (Snap On Coupling) 1 pcs. (Antenna)

• MOLEX 70555, 3 pin connector 1 pcs. (Wiring harness)

• MOLEX 70555, 4 pin connector 1 pcs. (Display)

Display:

• TPM-100 - A10-2489170 RX SW (IR switch with TPMS logo)

• MTPM-100 - Waeco Specific ID Design Switch.

• MOLEX 70066G, 4-pin connector (Terminals: MOLEX 70058-0022)

The terminals should be connected to the wiring but the connector should be separate in the kit. This

to enable a proper installation of the switch on the dashboard (as with IR-switch)

Antenna:

• 1 x 17cm flexible antenna and SMB connector (Snap On Coupling)

• 1 x 2.5 meter flexible antenna and SMB connector antenna

Wiring harness:

• MOLEX 70066G, 3 pin connector & MOLEX 70058-0022 terminals.

• 0.5- meter cable (2 pcs, red, orange and black) – Permanent Feed Connection on this system.

• Separate fuse with 15cm of wiring on each end. (Not connected to main wiring harness!)

Accessories:

• 3 cable ties (5x430mm)

• 1 double- sided pad (size of largest surface of the receiver-module)

• 1 double- sided pre shaped pad (VST (Very Strong Tape) #6080G) for fixing display.

PAGE 1
TPM-100 (MTPM-100) Product Description Kit content: 1. 2. 3. 4. 5. 6. 7. 4 Generation 1 Wheel sensors Receiver Display 1 x 17cm Wire Antenna 1 x 2.5 meter antenna Wiring harness Accessories Optional accessories: 1. 2. 3. 2 x Generation 1, Wheel Sensor Kit for 6 Wheel Vehicles Generation 1 Wheel sensor Valve (in separate items, as specified at “Wheel sensor”) Wheel sensor: • Specialized LITEON valve to be purchased from Record. 300-0087810 • Generation I sensor-unit (433.
PAGE 2
Functionality: Normal Operation Mode: As soon as the ignition is switched on, the system will perform a self-test. This self-test should take no longer than 108 seconds to be completed. The self-test period is defined as the period from the point that the ignition is switched on to the point that the Electronic Module receiver has received the latest Tire Conditions from each wheel taught to the system. If the system is permanently fed the signals are received when the ignition is switched off.
PAGE 3
PAGE 4
Tire Conditions: During the “Normal Operation Mode” the system will continuously check the condition of all tires. The conditions are then represented by 3 colors: Green Condition: The condition (pressure & temperature) of all tires is ok. (The tire pressure is between (>)75% and (<)150% of the Front or Rear Preset Pressure and the tire temperature is below 85°C.) Indication: The display (LED) will light up green and will turn off after 1 minute.