User's Manual

ManualsBrandsLiquid Image ManualsElectronicsEgo

Table Of Contents

Please note before use

1. Check if the Micro SD card of this equipment was installed properly.

2. Check if the memory card has enough free space.

3. The lithium battery must be fully charged before the first use. You can either

use the supplied USB cable and charge it with your computer, or use a wall

charger (sold separately)

4. A Liquid Image charging cable must be used to avoid damage to the camera.

1. 2.

. . .

. .

Shutter / Select / Wifi Start & Shutdown button LCD Display

3 Camera Lens 4 Mode Light Indicator 5 Power / Mode button

6 Microphone 7 USB Port 8 HDMI Port

9 Micro SD card slot 10 Accessory Knob

Accessories:Accessories:

Adjustable Flat Adhesive Mount Waterproof casing Protective face cover

Liquid Image will update the software regularly, please refer to the

information on our website and download the newest software.

www.liquidimageco.com

Part Names:

Basic information

(Shutter / Select / Wifi

Start & Shutdown button)

(Power / Mode button)

Mode button

Shutter

Turn on/off:

Firmware Upgrade Procedure:

The Camera will not function without a Micro SDHC card up to 32GB with a

class 6 or higher rating. Insert Micro SDHC card. Turn on the camera by pressing

the Mode button. The Camera will turn on in the 720p@60fps Mode (Blue LED).

The WiFi signal icon will begin flashing once the WiFi module is available in

about 8 seconds. To turn on the Wifi connection, press and hold the Shutter

button down for 3 seconds or until the WiFi icon becomes solid ( see WiFi

setting section of user manual). To turn off the camera, press and hold the

Mode button for three seconds.

If the camera remains in standby mode for three minutes, it will automatically

power off.

Note: If the WIFI function is on, the function of auto shut down will be inactive.

Copy the firmware file to the root directory of the SD card, outside of the main

directory folders. Then, disconnect the USB cable and the camera will

automatically shut down. Now, with the camera off, press and hold both the

on/off button and the shutter button. Once you hear the camera beep, release

both buttons at the same time.

(Please note that LCD will show UP during the process. After the upgrade finishes, the

camera will shut down automatically.)

TipsTips

SOS message

HOT message

When the camera shows SOS, it means the current recording document is

damaged; the user can press any key to repair this document.

LCD display the temperature of the camera is

too high for cooling

temperature of the equipment cannot

be too high

When the shows HOT, it means

and needs to shut down . It won't damage the camera and

is only for reminding the user that the

. The user only needs to reboot the camera after it cools down.

Mode Setting

WIFI wireless WIFI signal icon

Battery shows the battery level

Photo Mode Photo mode or

Continuous photo mode

SD card Icon flashes continuously when

no SD card is recognized

720 mode 720p@60 Frames per second mode

1080 mode 1080p@30 frames per second mode

Mode Switching

720P@60fps recording mode

1080P@30fps recording mode

Photo mode

Pressing the Power / Mode button cycles through the modes in the following

order: 720P 60, 1080P 30, Photo, and Continuous Photo. Press the SHUTTER

and mode buttons at the same time in the 720P/1080P mode will switch to the

PAL / NTSC standard. Press the mode button to switch, and press the SHUTTER

button to save and exit.

Press the SHUTTER button once in the preview mode the camera will start

recording. During the recording process, the blue LED light will flash. Press

again to stop recording the blue LED light will stay .

In the 720P 60 mode, press the ode button briefly to switch to the 1080P 30

mode. In the preview mode, press the SHUTTER button once the camera

will start recording. During the recording process, the green LED light will flash.

Press again to stop recording the green LED light will stay .

In the 1080P 30 mode, press the mode button briefly to switch to the Photo

mode, and the red LED light will be solid.

With the camera in standby mode, if you wish to take a single photo, press the

shutter button briefly. You will hear a beep and see the red LED flash once,

which indicates that a single photo has been taken.

When the camera is turned on, the default mode is 720p@60 frames per second.

This will be indicated by the LED showing solid blue. To switch between the

different modes of the camera, briefly press the mode button.

ing

and

and solid

and

and solid

- Blue LED

- Green LED

- red LED

TipsTips

Reminder

When the memory card is full, the LCD display will show FUL.

If you wish to format the memory card, please use the following operation:

Insert the memory card into the camera and hold the shutter button. Then,

press the Mode button continuously four times in a row. The LCD will then

show FAT on the screen which indicates that the MicroSD card is being

formatted.

Press MODE

botton

Press MODE

botton

LCD Display

If a Micro SD card is not inserted, and the camera is powered on, the SD card

icon on the right side will flash, as shown in P-01 below. If the Micro SD is

present in the camera, the LCD screen will display as shown in P-02. The display

in the DV mode is as pictured in P-03 below.

P-04

When the battery is low, the LCD display in Video mode will display like picture

P-05. When it is in Camera mode, it will display as shown in P-06. When no bars

remain, it will beep 3 times and the word "LO" flashes on the screen, and the LED

light will flash red. After it stops beeping, the battery icon will begin to flash.

When the battery is about to cut off, the camera will beep 9-12 times. At this

time, the video document that is in the process of recording will be saved before

the power is cut off, and the document will be able to be played normally.

When the USB is used to connect the camera to the computer, the LCD display

will display as shown in P-07. You may access or move the photos and video

files in the camera to the computer. At this time, the battery is also

simultaneously charging.

When an HDMI cable is used to connect to the TV, the LCD display will display as shown

in P-08. The TV will display as shown in P-09.

hen the camera is on, connect it to the TV via the HDMI cable. The camera will play

the first video automatically and stop after this video is completed. Then, press the

shutter button to play the next video, or press the mode button to play the previous

video. If you would like to switch to photo mode, press and hold the mode button for

3 seconds. WHen in photo mode, it will show the first photo automatically. Press the

shutter button to advance to the next photo, or press the mode button to display the

previous photo. To switch back to the video display, press and hold the mode button

for 3 seconds.

The TV screen will show the Digital Video playback icon, the battery symbol,

the video file number/total number of videos, and the playing time/total time.

Picture P-10 is what will be displayed on the TV when connected in photo

viewing mode. It will show the picture file number/ total file number and the

battery symbol.

Only turn the camera off after it has been disconnected from the HDMI cable,

as it will not turn off while still connected to the TV.

hen the camera is connected to both the computer and TV at the same time,

it will override to the MSDC mode, and the LCD screen will display "USB".

While charging, the battery symbol will show the animation

of the battery charging, and the camera will shut down

automatically when it has reached a full charge. If you

wish to use the camera while it is charging, you can press

the shutter button to switch to the 720p mode. Charging

will pause and you will be able to use the camera normally.

While charging, the LCD screen will display as in P-11.

The LCD display shows picture above.

F/W Upgrade Display When Using Micro SD Card:

Low battery

USB connection mode

HDMI connection mode

Note:

Charging

No SD Card

DV Mode(P-01)

SD Card

DSC Mode(P-02)

SD Card

DV Mode(P-03)

F/W

(P-04)

upgrading

DV Mode DSC Mode

(P-05) (P-06)

USB connect to PC Connect to TV

(P-07) (P-08)

00: 00 : 12

000 76/0 0 04000 76/0 0 04

Connect to TV - DV Mode(P-09)

001 68/0 0 12001 68/0 0 12

Connect to TV - DSC Mode(P-10)

Charging(P-11)

Year setting

First two numbers

setting

Next two numbers

setting

Month setting Date setting Clock setting Minute setting

Item Specifications

Insert slot

Base Connection stents

Specification

Video Resolution 1080p @30 frames per second,

720p @60 frames per second.

Video file format H.264 MOV

Audio Yes, Mono

Photo Resolution 12.0 Megapixels

Photo format JPEG

Internal memory 256MB

External memory Micro SDHC Class 6+ up to 32GB

Sensor 3MP sensor

Lens F/3.2

135 degree

Lens focus 0.4m to infinite

Shutter speed 1/2 to 1/8000 second

USB 2.0 High Speed

HDMI Mini HDMI output

Battery Power 1030mAh

WiFi Yes

Field of View

Accessory installation

Screw insert hole

Screw fixed axle

Picture of Assembly

Waterproof casing Assembly:Waterproof casing Assembly:

Insert the camera

Hook and

snap closed

Close the water

proof case

Description:

The waterproof housing for the Ego HD can allow you to use the camera in a

variety of environments. The flat adhesive mount connects directly to the

base of the housing and allows you a great amount of versatility and mounting

options.

Power On 1 Beep sound

Button Pressing 1 Beep sound

Wifi activation WIFI icon is solid

720P 60 Video mode Blue light flashes

1080P 30 Video mode Green light flashes

Photo mode Red light flashes once

Continous Photo mode Purple light flashes

Wifi shutdown Wifi icon flashes

Low battery, the battery Red light flashes, short continuous

symbol shows empty beep sounds.

(Sold separately)

User manual

Model: # 727

NEXT NEXT

P- A

The Wifi feature on the camera is off by default, as displayed by the flashing

WiFi icon

To activate the feature, simply hold the shutter button for two seconds,

and you will hear two beeps, and the LCD display will show a solid WiFi symbol.

The WiFi takes 8 seconds to boot, so do not press any buttons during this time.

After the WiFi is activated, press and hold the recording button for two seconds

to shut it off. This procedure will be indicated by a flashing WiFi symbol in the

LCD screen. When the WiFi is activated, it will automatically shut off if you press

the shutter button to begin recording, and will take 8 seconds to complete the

shut-down procedure.

(Note: The WiFi icon will take around 8 seconds after powering on

before it is shown on the LCD screen. Please do not press any buttons until you

see this icon)

(Note: If the WIFI is activated, it will auto switch off if you press shutter button

for recording. And the wifi shutdown process may take around 8 second.)

Wifi setting

Date, time setting

Protective Face Cover

Camera

Assembled

Warning:

1. Keep the sticking area clean

Please use care to follow the correct installation steps for the waterproof

housing to avoid damage to the camera from immersion.

The flat adhesive mount needs to attach to a smooth surface.

Apply the adhesive mount at room temperature.

Let the mount air-dry for 24 hours before use.

Continuous Photo mode

In the photo mode, press the mode button briefly to switch to the Continuous

Photo mode, and the purple LED light will be solid.

With the camera in standby mode (indicated by a solid purple LED) press the

shutter button briefly to activate the continuous shooting mode. You will hear

a beep and see the LED flash every time a photo is recorded. To stop the

continuous shot mode, press the shutter button again briefly, and the LED will

return to a solid state.

- purple LED

With the camera switched off, press the SHUTTER button and press the MODE

button for two seconds to activate the camera, hold the SHUTTER button, and

press the MODE button three times continously to enter the date and time

settings. The sequence of the display is: year-month-day- clock- minute.

The numbers in the LCD screen will flash. To change the numbers press the

mode button, and use the shutter button to confirm your selection.

After you have completed all of your selections for date and time, press the

shutter button and the mode button at the same time to save the settings

and exit.

This manual explains how to safely operate the Ego Sports Camera. Please read

these instructions carefully before using the camera.

Waterproof Casing Base Assembly:Waterproof Casing Base Assembly:

Protective Face Cover Assembly:Protective Face Cover Assembly:

Summary of content (2 pages)

PAGE 1
Continuous Photo mode - purple LED In the photo mode, press the mode button briefly to switch to the Continuous Photo mode, and the purple LED light will be solid. Date, time setting With the camera switched off, press the SHUTTER button and press the MODE button for two seconds to activate the camera, hold the SHUTTER button, and press the MODE button three times continously to enter the date and time settings. The sequence of the display is: year-month-day- clock- minute.
PAGE 2
WiFi application FCC Statement Commonly asked questions and troubleshooting Software installation: You can download and install the "Actionconnect" Application (App) from the Apple Store or Android marketplace. You will be able to see the icon for the application as shown in P-A Internet setting: Turn on the WiFi to your iOS/Android device and choose the network named "EGO".