Placing Calls Placing Calls 4. Press the (TIED button. The IN USE LED indicator will it up. 2. Listen fora dial one. 3. Dial the phone number. 4, When you have finished your call, press the (alk; button again. The INFUSE LED indicator will turn off. Redial Feature 4. if you get a busy tone, press the button to hang up. Later, press the (talk Button again. Listen for a dial tone. Press the (redial button. This will automatically redial the last telephone number you called.
Storing Numbers Storing Numbers 1. Be sure the BASE UNIT IN USE LED indicator is off and the HANDSET is in STANDBY made {See Special Features Section). 2. Press the button. 3. Dial the number you want to stare. 4. Pressie button again. 5. Dial the TELEPHONE KEYPAD (T) ~ (8) button where you want to store that number. You wife hear one confirmation “beep,” 8. Write the name of the person you will be calling with that number next to the corresponding TELEPHONE KEYPAD ori the TELEPHONE NUMBER CARD. 7.
Recalling Stored Numbers Recalling Stored Numbers from Memory 1. Press the (fal) button 2. Press the (emo button 3. Press the TELEPHONE KEYPAD for the number you have stored. The stored number will be dialed automatically. EXAMPLE: To recall number 115-1968 stored under TELEPHONE KEYPAD) ©. ®. button: ~ Press the (fall) bunion Press the {i Y eee meme’ button -: Eo Press the TELEPHONE KEYPAD © [Leslie ti To obtain the best reception, be sure to raise or reposition the BASE UNIT ANTENNA.
Security System Your cordless telephone uses a digital casing security system to prevent unauthorized use of your telephone line by another nearby cordless telephone, The System has its own identifying signal created by microcomputers in both the BASE UNIT and the HANDSET. Security Code This telephone has an internal security code with 65,536 possible combinations.
1 EX-BASIC p55. © YASHMAK, 220 PME In Recharging the BATTERY PACK Battery Type Use the following type and size of BATTERY PACK: Cordless Telephone BATTERY PACK mah & US, Electronics Inc. Ni-Cd BATTERY PACK: Model 8650 Ni-Cd This BATTERY PACK is available through: U.8. Electronics Service Center 105 Madison Avenue New York, NY 10016 1-800-828-5208 Recharging the BATTERY PACK The nickel cadmium (Ni-Cd) BATTERY PACK in the HANDSET can be recharged many Hines using the built-in charger in the BASE UNIT.
1 Changing the BATTERY PACK Changing the BATTERY PACK The BATTERY PACK provides power for the HANDSET of your cordless telephone. To Replace the BATTERY PACK: 1. Remove the HANDSET BATTERY COMPARTMENT COVER by sliding it down. 2. Pullout the BATTERY PACK PLUG and remove the BATTERY PACK. 3. Plug the new BATTERY PACK into the BATTERY CONNECTOR. 4. Side the HANDSET BATTERY COMPARTMENT COVER firmly into place in its closed position. 8. Before use. charge the new BATTERY PACK for 12 hours.
Le CLE RV Problem Solving Section For your assistance, we have listed below a few common problems. Phone does not work, check the following: 1. BASE UNIT is plugged into power source. 2. HANDSET js charged. 3. TONE/PULSE switch is in the right position. 4. TELEPHONE LINE CORD is plugged into the TELEPHONE JACK. Range of phone limited, check the following: 1. ANTENNA on the BASE UNIT is raised. 2. BASE Unit Is centrally located in your residence. 3.
ERT ol 5 Technical Information Technical Information This cordless telephone uses radio frequencies to allow mobility. There are certain difficulties in using radio frequencies with a cordless telephone. While these are normal, the following could affect the operation of your system. Noise . Electrical purse noise is present in most homes at one time or another. This noise is mast intense during electrical storms.
FCC Requirements Federal Communications Commission Requirements This equipment complies with Part 63 of the FGC Rules. A label on the BASE UNIT of this equipment contains, among other information, the FCC Registration Number and the Ringer Equivalence Number (REN) for this equipment.