User's Manual

ManualsBrandsLinx Technologies ManualsElectronicsGen1+ RFRX Motor Actuation Controller



RollRiteRADIOFREQUENCYRECEIVER/RADIOFREQUENCYTRANSMITTERInstruction Page1



RollRiteAutomatedTarpSystem

RemoteControlOwner’sGuide

ComponentPhotos

RadioFrequencyTransmitter(figure)

RadioFrequencyReceiver(figure)



ConnectingRFReceivertoMotorController

InstallationRequirements

 Allelectricalterminalsshallbecoatedwithdielectricgrease,SyntheticNLGIGrade2or

equivalent

 RemovenegativeelectricalterminalsofallchassisbatteriespriortoinstallationofRollRite

components

 RollRitemotorrelayandRadioFrequencyReceivershallbeinstalledonaverticalplanewiththe

wires

fromterminalsfacingdown.Thisistheonlyapprovedinstall a tionorientationforRollRite

electricalcomponents

 TorqueMotorRelayTermi nal7/16”fastenersto8ft.lb(11Nm)

InstallationProcedure



1. DisconnectallMainNegativeBatteryTerminalsfromtheVehicleBatterySystem,thereby

isolatingstoredelectricalenergyfromRollRitetarpsystemcomponents

2. ConnectRollRiteMotorController

a. ConnectPositivePowertoBat+Terminal,SlideRedBootoverTerminalconnection

b. ConnectNegativePowertoGNDTerminal,SlideBlack

BootoverTerminalconnection

c. ConnectBlueMotorCabletoM1Terminal,SlideBlueBootoverTerminalconnection

Summary of content (5 pages)

PAGE 1
Roll Rite Automated Tarp System Remote Control Owner’s Guide Component Photos Radio Frequency Transmitter (figure) Radio Frequency Receiver (figure) Connecting RF Receiver to Motor Controller Installation Requirements     All electrical terminals shall be coated with dielectric grease, Synthetic NLGI Grade 2 or equivalent Remove negative electrical terminals of all chassis batteries prior to installation of Roll Rite components Roll Rite motor relay and Radio Frequency Receiver shall be installed on
PAGE 2
d. Connect Yellow Motor Cable to M2 Terminal, Slide Yellow Boot over Terminal connection 3. Connect Radio Frequency Receiver to Roll Rite Motor Controller a. Add dielectric grease to all ¼” terminals of the Radio Frequency Receiver and Motor Controller b. Connect ¼” Flag Terminal of Red Wire to BAT+ Terminal c. Connect ¼” Flag Terminal of Black Wire to GND Terminal d. Connect ¼” Flag Terminal of Yellow Wire to FWD Terminal e. Connect ¼” Flag Terminal of Blue Wire to REV Terminal 4.
PAGE 3
. On the transmitter select the “Tarp” Cover and Uncover button simultaneously (figure) 4. The receiver LED will flash 1 time, indicating the transmitter has paired with the Tarp Motor Receiver Front Hopper Motor Pairing: 1. On the receiver/relay connected to the hopper motor at the front of the trailer, press Uncover and Pair at the same time, the Receiver LED will flash indicating pairing has started (figure) 2.
PAGE 4
Specifications FCC Statement of Compliance This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 5
puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le présent émetteur radio (IC: [IC Company number of your product]) de modèle s'il fait partie du matériel de catégorie I) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci‐dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne.