Wi.USB-DTS™ User’s Manual Rev 1.0.3 905 Messenger Ln.
RK-Wi.232DTS-FCC Rapid Development Kit User’s Manual Document Control Created By Engineering Review Marketing Review Approved – Engineering Approved – Marketing Gordon Hudson 2/15/06 Revision History Revision 1.0.0 1.0.1 1.0.2 1.0.3 Author GWH TRM TRM TRM Date 2/15/06 2/21/06 2/23/06 3/29/06 © 2006 Radiotronix Inc, all rights reserved Description Document Created from FCC-DTS 1.0.
RK-Wi.232DTS-FCC Rapid Development Kit User’s Manual Table of Contents 1 Description ...............................................................................................................................3 2 Wi.USB Setup ..........................................................................................................................3 3 Using Wi.USB-DTS™ Evaluation Software..............................................................................4 3.1 COM Port Setup and Selection.
RK-Wi.232DTS-FCC Rapid Development Kit User’s Manual 1 Description The Wi.USB-DTS™ is a self-powered, standalone desktop transceiver based on the Radiotronix Wi.232DTS module. The unit draws its power from the USB port. 2 Wi.USB Setup • Install the USB driver in Windows. Do not connect the Wi.USB-DTS™ to your PC without first installing the driver. To install the driver, run the Silicon Laboratories CP210x UART to USB Bridge Driver as illustrated below.
RK-Wi.232DTS-FCC Rapid Development Kit User’s Manual 3 Using Wi.USB-DTS™ Evaluation Software The software supplied with the Wi.USB-DTS™ is used to read and set the volatile and non-volatile registers within the Wi.232DTS™ module contained within. Additionally, it provides a chat interface for basic information exchange. Please refer to the Wi.232DTS™ User’s Manual for more information on the register settings. 3.1 COM Port Setup and Selection. Upon starting the Wi.
RK-Wi.232DTS-FCC Rapid Development Kit 3.3 User’s Manual Non-Volatile Register Page. The Non-Volatile Register page in the evaluation software allows you to change the default settings which will be loaded when the module is powered on. It is important to note that data rates in excess of 19.2kbps cannot be achieved in LP mode due to bandwidth limitations. Tip: If you change the Non-Volatile Data Rate setting, you will have to select this baud rate when you start the Wi.USBDTS™ evaluation software. 3.
RK-Wi.232DTS-FCC Rapid Development Kit User’s Manual 4 Evaluation Software Functions 4.1 Setting Register Values. On both the Volatile and Non-Volatile pages, the registers are labeled by function. To set a register value, select the value from the options available for that register and click the “Write” button. To perform a read of that register, simply click the “Read” button. Descriptions of the register functions can be found in the Wi.232DTS™ User’s Manual. 4.
RK-Wi.232DTS-FCC Rapid Development Kit User’s Manual 5 Notes 5.1 Microsoft Windows / Hilgraeve HyperTerminal The Wi.USB-DTS™ can be used with HyperTerminal to receive and transmit RS-232 data and send files using file transfer protocols such as ZMODEM. HyperTerminal and many other terminal programs assert RTS by default. In the Wi.USB-DTS™, the RTS line is tied to the CMD pin on the module inside the Wi.USB-DTS™ .
RK-Wi.232DTS-FCC Rapid Development Kit User’s Manual 6 FCC Statements of Compliance 6.1 Class B Digital Device Statement FCC NOTICE (FCC ID: Q7V-3F090012X) This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
RK-Wi.232DTS-FCC Rapid Development Kit 6.2 User’s Manual Declaration of Conformity FCC NOTICE (FCC ID: Q7V-3F090012X) This device complies with the rules set forth in Part 15 by the Federal Communications Commission. Operation is subject to the following two conditions: 1) This device may not cause harmful interference 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by Radiotronix, Inc.
RK-Wi.232DTS-FCC Rapid Development Kit 6.3 User’s Manual Radiation Exposure Statement FCC NOTICE (FCC ID: Q7V-3F090012X) The antennas used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Product: Wi.USB-DTS™ FCC ID: Q7V-3F090012X 6.4 Modifications FCC NOTICE (FCC ID: Q7V-3F090012X) Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Product: Wi.
