Network PTZ Camera·Quick Start Guide Network PTZ Camera Quick Start Guide i
Network PTZ Camera·Quick Start Guide Quick Start Guide COPYRIGHT © 2018 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
Network PTZ Camera·Quick Start Guide Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY.
Network PTZ Camera·Quick Start Guide IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.
Network PTZ Camera·Quick Start Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Network PTZ Camera·Quick Start Guide 2015/35/EU, the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information, please see: www.recyclethis.info.
Network PTZ Camera·Quick Start Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected. Warnings Follow these safeguards to prevent serious injury or death.
Network PTZ Camera·Quick Start Guide Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard. Make sure that the plug is firmly connected to the power socket. Make sure that the power has been disconnected before you wire, install or dismantle the PTZ camera. When the product is mounted on wall or ceiling, the device shall be firmly fixed.
Network PTZ Camera·Quick Start Guide Do not touch senor modules with fingers. If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an extended period, replace the lens cap to protect the sensor from dirt. Do not aim the camera at the sun or extra bright places. Blooming or smearing may occur otherwise (which is not a malfunction), and affect the endurance of sensor at the same time.
Network PTZ Camera·Quick Start Guide Table of Contents 1 Overview ......................................................................................... 1 1.1 Introduction ............................................................................. 1 1.2 Cable Descriptions .................................................................... 1 1.3 Alarm Output............................................................................ 2 2 Installation ....................................................
Network PTZ Camera·Quick Start Guide 2.7 Installing DE4AxxxI Series PTZ Camera .................................... 37 2.7.1 Ceiling Mounting ............................................................. 37 2.7.2 In-ceiling Mounting ......................................................... 38 3 Setting the PTZ Camera over the LAN........................................... 41 3.1 Wiring .................................................................................... 41 3.2 Activating the Camera .........
Network PTZ Camera·Quick Start Guide 1 Overview 1.1 Introduction The network PTZ camera has the following series: DE1Axxx(I) Series PTZ Camera DE2Axxx(I) Series PTZ Camera DE2xxx(I) Series PTZ Camera DE3xxx Series PTZ Camera DY3xxx Series PTZ Bullet Camera DE4AxxxI Series PTZ Camera Integrated with an optical zoom lens, this series of cameras feature in the PTZ limits, 3D positioning, Day/Night auto switch, 3D DNR, etc., and are widely applied in various kinds of environments. 1.
Network PTZ Camera·Quick Start Guide Power Cord DC12V IN Video Cable RS-485 Alarm Cable .. Audio Cable Network Cable Figure 1-1 Cables of PTZ Camera Power Cord: Supports 12 VDC power supply. Video Cable: Connect BNC Cable to test the video output. Alarm Cable: Connect terminal ALARM-IN with GND interface, and connect terminal ALARM-OUT with ALARM-COM interface. Audio Cable: Connect terminal AUDIO-IN with GND interface.
Network PTZ Camera·Quick Start Guide GND Output DC 30V 1A Power Supply JQC-3FG Relay (10A 250VAC) Direct load Relay Output OUT (n) OUT (n) + DC - ~220V AC Relay Output OUT (n) OUT (n) Figure 1-2 Alarm Output 3 FireWire Zero Line
Network PTZ Camera·Quick Start Guide 2 Installation Before you start: Check the package contents and make sure that the device in the package is in good condition and all the assembly parts are included. Notes: Do not drag the PTZ camera with its waterproof cables; otherwise the waterproof performance is affected. Do not touch the bubble directly by hand. The image blurs otherwise. Do not power up the camera until the installation is finished.
Network PTZ Camera·Quick Start Guide Crack Cover 2.0 Figure 2-1 Open the Cover 2. Unscrew the screws on the camera base with the cross screwdriver, and remove the bubble, as shown in Figure 2-2. Bubble Screw Figure 2-2 Remove the Bubble 3. Open the memory card slot in the camera, and insert the memory card. 4. Align the bubble with the camera base, and install the bubble back. Fix the bubble with four screws, as shown in Figure 2-3.
Network PTZ Camera·Quick Start Guide Figure 2-3 Install the Bubble 5. Align the cover with the camera, and install the cover back, as shown in Figure 2-4.
Network PTZ Camera·Quick Start Guide 2.1.2 DE2Axxx(I) Series PTZ Camera Note: The installation steps are similar to the installation steps of DE1Axxx(I) series camera. Refer to section 2.1.1 DE1Axxx(I) Series PTZ Camera. 2.1.3 DE2xxx(I) Series PTZ Camera Steps: 1. Open the memory card cover.
Network PTZ Camera·Quick Start Guide 2. Rotate the cover to a proper position, align the memory card with the memory card slot and insert it. Figure 2-7 Insert the Memory Card 3. Rotate the cover and push it back. 2.1.4 DE3xxx Series PTZ Camera Steps: 1. Loosen three screws on the bottom of camera to reveal the memory card slot, as shown in Figure 2-8.
Network PTZ Camera·Quick Start Guide 2. Align the memory card with the memory card slot and insert it. 3. Fix the screws and assemble the PTZ camera. 2.1.5 DY3xxx Series PTZ Bullet Camera For DY3xxx series PTZ bullet camera, the memory card slot is in the camera module and if you need, the memory card can be installed before the camera leaves the factory. In order to prevent damage, we highly recommend that you do not disassemble the PTZ bullet camera by yourself. 2.1.
Network PTZ Camera·Quick Start Guide Decorative Rim Bubble Flange Srews Figure 2-10 Remove the Bubble and the Decorative Rim 3. Open the memory card cover and insert the memory card into the card slot as shown in Figure 2-11 and Figure 2-12.
Network PTZ Camera·Quick Start Guide Memory Card Slot Memory Card Cover Figure 2-12 For 4× Camera Module 4. Close the memory card cover. Fix the four flange screws and push four silicone plugs back to assemble the PTZ camera. 2.2 Installing DE1Axxx(I) Series PTZ Camera 2.2.1 Ceiling Mounting Notes: The thickness of the ceiling shall range from 5 mm to 40 mm. Make sure the ceiling is strong enough to withstand more than four times the weight of the PTZ camera and its accessories. Steps: 1.
Network PTZ Camera·Quick Start Guide OPEN Installation Plate Figure 2-13 Remove the Installation Plate 2. Drill four screw holes in the ceiling according to the installation plate. 3. Align the installation plate with the screw holes, and fix the installation plate on the ceiling.
Network PTZ Camera·Quick Start Guide 4. Route the cables from the cable hole in the installation plate. 5. Align the camera with the installation plate, and rotate the camera clockwise to fix it, as shown in Figure 2-15. LOCK OPEN Figure 2-15 Fix the Camera 2.2.2 Wall Mounting Notes: For cement wall, you need to use the expansion screw to fix the bracket. The mounting hole of the expansion pipe on the wall should align with the mounting hole on the bracket.
Network PTZ Camera·Quick Start Guide 1. Remove the installation plate, and install it on the wall mounting bracket (not supplied) with two screws. Note: Refer to step 1 in section 2.2.1 Ceiling Mounting to remove the installation plate. Figure 2-16 Install the Installation Plate 2. Loosen the fixing screw on the bracket and remove the bracket base. Fixing Screw Bracket Base Figure 2-17 Remove the Bracket Base 3. Install the bracket base on the wall with four screws.
Network PTZ Camera·Quick Start Guide Figure 2-18 Install the Bracket Base 4. Route the cables. Align the camera with the installation plate on the wall mounting bracket, and rotate the camera clockwise to fix it on the bracket. OPEN LOCK Figure 2-19 Install the Camera 5. Connect the cables. Install the wall mounting bracket to the bracket base on the wall, and fix it with the supplied screw.
Network PTZ Camera·Quick Start Guide Figure 2-20 Fix the Bracket 6. Remove the protective film after installation. 2.3 Installing DE2Axxx(I) Series PTZ Camera Note: The installation steps are similar to the installation steps of DE1Axxx(I) series camera. Refer to section 2.2 Installing DE1Axxx(I) Series PTZ Camera. 2.4 Installing DE2xxx(I) Series PTZ Camera DE2xxx series PTZ camera supports wall mounting, ceiling mounting, and installing with junction box.
Network PTZ Camera·Quick Start Guide For wooden wall, you can just use the self-tapping screw to fix the bracket. Make sure that the wall is strong enough to withstand more than eight times the weight of the PTZ camera and its accessories. Steps: 1. Rotate the base plate counterclockwise to separate it from the PTZ camera.
Network PTZ Camera·Quick Start Guide 2. Align the cable hole on the base plate with the hole on the bracket for wiring. And install the base plate to the bracket by fixing three PM4×10 screws (supplied) to the holes marked with digit “2” on the bracket. Figure 2-23 For DE2xxx Series PTZ Camera Figure 2-24 For DE2xxxI Series (IR) PTZ Camera 3. Route the cables through the cable hole. 4. Align the PTZ camera with the base plate.
Network PTZ Camera·Quick Start Guide OPEN LOCK Figure 2-25 Secure DE2xxx Series PTZ Camera OPEN LOCK Figure 2-26 Secure DE2xxxI Series (IR) PTZ Camera 5. Secure the mounting base to the wall with four PA4×25 screws (supplied).
Network PTZ Camera·Quick Start Guide Figure 2-27 Install the Mounting Base 6. Install the PTZ camera to the bracket. 1). Route the cables of the PTZ camera through the wall bracket. 2). Connect the corresponding cables. 3). Hang the bracket together with the PTZ camera on the mounting base. 4). Fix the mounting base with a PM4×10 screw. Figure 2-28 Secure the Mounting Base 2.4.
Network PTZ Camera·Quick Start Guide Notes: The ceiling mounting is applicable to the indoor/outdoor solid ceiling construction. The followings are the mandatory precondition for ceiling mounting: The thickness of the ceiling shall range from 5 mm to 40 mm. Make sure the ceiling is strong enough to withstand more than four times the weight of the PTZ camera and its accessories.
Network PTZ Camera·Quick Start Guide Ceiling Mounting without Junction Box Steps: 1. Rotate the base plate counterclockwise to separate it from the PTZ camera, as shown in Figure 2-21 and Figure 2-22. 2. Attach the drill template (supplied) to the place where you want to fix the PTZ camera, and make sure the front arrow appoints to the monitoring area. Figure 2-31 Attach the Drill Template 3.
Network PTZ Camera·Quick Start Guide Cable Slot Cover Figure 2-33 For DE2xxxI Series (IR) PTZ Camera 4. Attach the base plate to the ceiling and secure it with the supplied three self-tapping screws by aligning with three screw holes in the ceiling, and the front arrows on the drill template and base plate should be aligned together as well, as shown in Figure 2-34 and Figure 2-35.
Network PTZ Camera·Quick Start Guide Figure 2-35 For DE2xxxI Series (IR) PTZ Camera 5. Route the cables through the cable hole. 6. Align the PTZ camera with the base plate. Rotate the PTZ camera clockwise into the base plate, and the PTZ camera is secured with the base plate by three locks on the plate.
Network PTZ Camera·Quick Start Guide 2.4.3 Installing with Junction Box Notes: The thickness of the ceiling shall range from 5 mm to 40 mm. Make sure the ceiling is strong enough to withstand more than four times the weight of the PTZ camera and its accessories. Steps: 1. Rotate the base plate counterclockwise to separate it from the PTZ camera. Notes: The base plate is not required when you install the PTZ camera with junction box. Keep it properly.
Network PTZ Camera·Quick Start Guide OPEN Base Plate on the Bottom of the Dome Front View of Base Plate Figure 2-38 For DE2xxxI Series (IR) PTZ Camera 2. Attach the drill template (supplied) to the place where you want to fix the PTZ camera, and make sure the front arrow appoints to the monitoring area. 3. Insert two PM4×10 screws into the ceiling, as shown in Figure 2-39. Figure 2-39 Attach the Drill Template 4.
Network PTZ Camera·Quick Start Guide on the drill template and junction box should be aligned together as well. Figure 2-40 Fix the Junction Box 5. Connect the cables and route the cables clockwise through the hooks and fix the camera and the junction box with three hooks. Tighten it clockwise and loosen it anticlockwise. Cable Outlet OPEN LOCK Figure 2-41 Fix the Camera 6. Secure the PTZ camera and remove the protective film.
Network PTZ Camera·Quick Start Guide 2.5 Installing DE3xxx Series PTZ Camera DE3xxx series PTZ camera supports ceiling mounting and in-ceiling mounting. Note: Wall mounting, installation with junction box, and installation with tripod are supported for DE3xxx series PTZ camera. The corresponding accessories shall be purchased separately. 2.5.1 Ceiling Mounting Notes: The thickness of the ceiling shall range from 5 mm to 40 mm.
Network PTZ Camera·Quick Start Guide Figure 2-42 Attach the Drill Template 3. Insert the expansion screws into the ceiling. (Optional) 4. Insert four PM4×10 screws into the ceiling and fix the base plate, as shown in Figure 2-43. Make sure the FRONT arrow of the base plate is of the same direction as the arrow of the drill template. Figure 2-43 Fix the Base Plate 5. Connect the cables and route the cable through the cable outlet. Align the PTZ camera with the base plate.
Network PTZ Camera·Quick Start Guide clockwise into the base plate, and the PTZ camera is secured with the base plate by three locks on the plate. 6. Fix the screws on the side with a screwdriver, as shown in Figure 2-44. ③ ① OPEN ② LOCK Figure 2-44 Fix the Camera 7. Secure the PTZ camera and remove the protective film. 2.5.2 In-ceiling Mounting Notes: Reserve at least 250 mm of height for in-ceiling mounting. The thickness of the ceiling shall range from 5 mm to 40 mm.
Network PTZ Camera·Quick Start Guide Figure 2-45 Drill Template 2. Fix the base plate onto the in-ceiling bracket with the four screws in the package (supplied). Make sure that the cable holes of the base plate are aligned to the cable holes of the bracket, as shown in Figure 2-46. Figure 2-46 Fix the Base Plate to In-ceiling Bracket 3. Connect the cables and route the cable through the cable hole.
Network PTZ Camera·Quick Start Guide 4. Align the PTZ camera with the base plate. Rotate the PTZ camera clockwise into the base plate, and the PTZ camera is secured with the base plate by three locks on the plate. 5. Fix the screws on the side with a screwdriver, as shown in Figure 2-47. ③ ① OPEN ② LOCK Figure 2-47 Fix the Camera 6. Fix the decorative rim with the bubble and the decorative rim will be attached to the in-ceiling bracket automatically, as shown in Figure 2-48.
Network PTZ Camera·Quick Start Guide 2.6 Installing DY3xxx Series PTZ Bullet Camera 2.6.1 Dimensions of DY3xxx Series PTZ Bullet Camera Two structures of DY3xxx Series PTZ bullet cameras are available: wall-mounted PTZ bullet camera and base-mounted PTZ bullet camera. Select the proper PTZ bullet camera and the installation method according to its working environment. Dimensions of wall-mounted PTZ bullet camera is shown in Figure 2-49. 157 367 242 122 φ105 4-φ7 (74.2) (74.
Network PTZ Camera·Quick Start Guide 157 255 195 129 129 4-φ7 100 100 Unit: mm Figure 2-50 Base-mounted PTZ Bullet Camera 2.6.2 Wall Mounting Before you start: The wall-mounted PTZ bullet camera can be installed on cement wall and pole mounting. The installing environment shall meet the following conditions: For cement wall, you need to use the expansion screw to fix the bracket. The mounting hole of the expansion pipe on the wall should align with the mounting hole on the bracket.
Network PTZ Camera·Quick Start Guide 1. Drill screw holes on the wall according to the dimensions of wall-mounted camera and insert four M6 expansion screws into the screw holes, as shown in Figure 2-51. Figure 2-51 Drill Screw Holes 2. Route the cables through the camera bracket and cover the four hex nuts with flat washers. 3. Fix the camera on the wall by knocking the expansion screws into the wall through the bracket, as shown in Figure 2-52.
Network PTZ Camera·Quick Start Guide 2.6.3 Base Mounting Before you start: Base-mounted PTZ bullet camera can be installed on hard plane structures such as cement surface. Note: Make sure that the plane structure is strong enough to withstand more than eight times the weight of the PTZ camera and its accessories. Steps: 1. Drill screw holes on the plane surface according to the dimensions of base-mounted camera. 2.
Network PTZ Camera·Quick Start Guide 2.7 Installing DE4AxxxI Series PTZ Camera DE4AxxxI series (IR) PTZ camera supports ceiling mounting and in-ceiling mounting. Note: Wall mounting, pendant mounting, and installation with junction box are supported for DE4AxxxI series (IR) PTZ camera. The corresponding accessories shall be purchased separately. 2.7.1 Ceiling Mounting Ceiling mounting for DE4AxxxI series (IR) PTZ camera is similar to ceiling mounting for DE2xxx series & DE2xxxI series (IR) PTZ camera.
Network PTZ Camera·Quick Start Guide 2.7.2 In-ceiling Mounting Notes: Reserve at least 250 mm of height for in-ceiling mounting. The thickness of the ceiling shall range from 5 mm to 40 mm. Make sure the ceiling is strong enough to withstand more than four times the weight of the PTZ camera and its accessories Steps: 1. Rotate the base plate counterclockwise to separate it from the PTZ camera, as shown in Figure 2-55.
Network PTZ Camera·Quick Start Guide Ø 2 21 Figure 2-56 Drill Template 3. Align the cable holes of the base plate to the cable holes of the in-ceiling bracket and then fix the base plate onto the bracket with the four screws in the package (supplied), as shown in Figure 2-57. Figure 2-57 Fix the Base Plate to In-ceiling Bracket 4. Connect the cables and route the cables through the cable hole. 5. Align the PTZ camera with the base plate.
Network PTZ Camera·Quick Start Guide ② Fix the Screw ① OPEN LOCK Figure 2-58 Fix the Camera 7. Place the camera and the bracket into the hole drilled in step 2, and rotate the screws clockwise to fix the camera. 8. Fix the decorative rim with the bubble and the decorative rim will be attached to the in-ceiling bracket automatically, as shown in Figure 2-59.
Network PTZ Camera·Quick Start Guide 3 Setting the PTZ Camera over the LAN Notes: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, strengthen your own protection. If the product does not work properly, contact with your dealer or the nearest service center. To ensure network security of the network PTZ camera, we recommend you to have the camera assessed and maintained termly.
Network PTZ Camera·Quick Start Guide or le ab rk C 网络交换机 o tw Ne Network PTZ Camera Ne two rk C abl e Computer Figure 3-2 Connecting via a Switch or a Router 3.2 Activating the Camera Purpose: You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via web browser, activation via SADP, and activation via client software are supported.
Network PTZ Camera·Quick Start Guide Notes: The default IP address of the camera is 192.168.1.64. The computer and the camera should belong to the same subnet. For the camera enables the DHCP by default, you need to use the SADP software to search the IP address. Figure 3-3 Activation Interface (Web) 3. Create a password and input the password into the password field.
Network PTZ Camera·Quick Start Guide 3.2.2 Activation via SADP Software SADP software is used for detecting the online device, activating the device, and resetting the password. Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera. Steps: 1. Run the SADP software to search the online devices. 2. Check the device status from the device list, and select an inactive device. Select inactive device.
Network PTZ Camera·Quick Start Guide 3. Create a password and input the password in the password field, and confirm the password. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Network PTZ Camera·Quick Start Guide Use the SADP software or client software to search and change the IP address of the device. We take modifying the IP Address via SADP software as an example to introduce the IP address modification. Note: For IP address modification via client software, refer to the user manual of client software. Steps: 1. Run the SADP software. 2. Select an active device. 3.
Network PTZ Camera·Quick Start Guide Figure 3-5 Modify the IP Address Note: You can enable the Hik-Connect service for the device during activation. Refer to section 5.1 Enable Hik-Connect Service on Camera. 4. Input the admin password and click Modify to activate your IP address modification. The batch IP address modification is supported by SADP. Refer to the user manual of SADP for details.
Network PTZ Camera·Quick Start Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version/Vista/Win7/Server 2003/Server 2008 32bits CPU: Intel Pentium IV 3.0 GHz or higher RAM: 1G or higher Display: 1024 × 768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.02 and above version, Mozilla Firefox 5 and above version and Google Chrome 18 and above version Steps: 1. Open the web browser. 2.
Network PTZ Camera·Quick Start Guide 4. Click Login. Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the network PTZ camera. Follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in. Figure 4-2 Download Plug-in 6. Reopen the web browser after the installation of the plug-in and repeat the above steps 2-4 to login.
Network PTZ Camera·Quick Start Guide Note: For detailed instructions of further configuration, refer to the user manual of the network camera.
Network PTZ Camera·Quick Start Guide 5 Operating via Hik-Connect App Purpose: Hik-Connect is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so on. Note: Hik-Connect service is not supported by certain camera models. 5.1 Enable Hik-Connect Service on Camera Purpose: Hik-Connect service should be enabled on your camera before using the service. You can enable the service through SADP software or web browser. 5.1.
Network PTZ Camera·Quick Start Guide Figure 5-1 Verification Code Setting (SADP) Note: The verification code is required when you add the camera to Hik-Connect app. 3. Click and read "Terms of Service" and "Privacy Policy". 4. Confirm the settings. 5.1.2 Enable Hik-Connect Service via Web Browser Before you start: You need to activate the camera before enabling the service. Refer to section 3.2 Activating the Camera.
Network PTZ Camera·Quick Start Guide Steps: 1. Access the camera via web browser. Refer to section 4 Accessing via Web Browser. 2. Enter platform access configuration interface: Configuration > Network > Advanced Settings > Platform Access Figure 5-2 Platform Access Configuration (Web) 3. Select Platform Access Mode as Hik-Connect. 4. Check the Enable checkbox. 5. Click and read "Terms of Service" and "Privacy Policy" in pop-up window. 6.
Network PTZ Camera·Quick Start Guide 5.2 Hik-Connect Setup Steps: 1. Download and install the Hik-Connect app by searching “Hik-Connect” in App Store or Google PlayTM. 2. Launch the app and register for a Hik-Connect user account. 3. Log in Hik-Connect app after registration. 5.3 Adding Camera to Hik-Connect Before you start: You need to enable the Hik-Connect service on camera before adding it to your Hik-Connect account. Refer to section 5.1 Enable Hik-Connect Service on Camera. Steps: 1.
Network PTZ Camera·Quick Start Guide You can find the QR code on the camera or on the cover of the quick start guide of the camera in the package. Figure 5-4 Scan QR Code Note: If the QR code is missing or too blur to be recognized, you can also add the camera by tapping the icon and inputting the camera's serial number. 3. Input the verification code of your camera. Notes: The required verification code is the code you create or change when you enabling Hik-Connect service on camera.
Network PTZ Camera·Quick Start Guide 5.4 Initializing the Memory Card Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. You can then start recording any event triggered video in the camera such as motion detection.
Network PTZ Camera·Quick Start Guide 57 UD09613B-A
