LK8355 ShenZhen Linkiing Technology Co,.LTD LK8353 Bluetooth 5.2 BLE Module DATASHEET V1.0 Shenzhen Linkiing Tech Co., Ltd 1 / 17 www.linkiing.
LK8355 Version update notes: Version V1.0 Date 2021-5-13 Update content First release Dylan Contact: Shenzhen Linkiing Technology co., LTD E-Mail:Dylan.xia@linkiing.com Phone:13510925951 Address:Floor 2, Building 5, Lihe Industrial Area, 1055 SongBai Road, Xili Town, Nanshan District, Shenzhen, China Shenzhen Linkiing Tech Co., Ltd 2 / 17 www.linkiing.
LK8355 1. Introduction: Key feature: The LK8355 highlighted features are listed below.
LK8355 Wireless applications include: • Lighting • Connected Home • Gateways and Digital Assistants • Building Automation and Security Architecture: Shenzhen Linkiing Tech Co., Ltd 4 / 17 www.linkiing.
LK8355 Size: PIN: Shenzhen Linkiing Tech Co., Ltd 5 / 17 www.linkiing.
LK8355 P IN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 N am e G PIO G PIO G PIO G PIO G PIO GND VCC R ST G PIO G PIO G PIO G PIO G PIO G PIO GND VCC G PIO G PIO G PIO G PIO G PIO G PIO G PIO R ST Shenzhen Linkiing Tech Co.
LK8355 Secondary flows welding temperature control diagram: Shenzhen Linkiing Tech Co., Ltd 7 / 17 www.linkiing.
LK8355 4.4 Precautions for the use of Bluetooth modules (1) Bluetooth use environment, wireless signal applications are greatly affected by the surrounding environment, such as trees, metals and other obstacles will have a certain absorption of wireless signal, so that in practical applications, the distance of data transmission is affected by a certain degree.
LK8355 Antenna Antenna Size: Shenzhen Linkiing Tech Co., Ltd 9 / 17 www.linkiing.
LK8355 Label Stickers: 10mm*10mm Model: LK8353 FCC ID: 2A8JX-LK8353 IC: 20034-LK8353 Shenzhen Linkiing Tech Co., Ltd 10 / 17 www.linkiing.
LK8355 FCC Statement Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The modular can be installed or integrated in mobile or fix devices only. This modular cannot be installed in any portable device. FCC Radiation Exposure Statement The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
LK8355 and 15.209 requirement, Only if the test result comply with FCC part 15C : 15.247 and 15.209 requirement,then the host can be sold legally. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
LK8355 following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
LK8355 OEM INTEGRATION INSTRUCTIONS: This device is intended only for OEM integrators under the following conditions: The module must be installed in the host equipment such that 20 cm is maintained between the antenna and users, and the transmitter module may not be co-located with any other transmitter or antenna. The module shall be only used with the internal on-board antenna that has been originally tested and certified with this module. External antennas are not supported.
LK8355 2.3 Summarize the specific operational use conditions Describe use conditions that are applicable to the modular transmitter, including for example any limits on antennas, etc. For example, if point-to-point antennas are used that require reduction in power or compensation for cable loss, then this information must be in the instructions.
LK8355 (1) to the host product manufacturer, to define the application conditions (mobile, portable – xx cm from a person’s body); and (2) additional text needed for the host product manufacturer to provide to end users in their end-product manuals. If RF exposure statements and use conditions are not provided, then the host product manufacturer is required to take responsibility of the module through a change in FCC ID/IC (new application).
LK8355 2.9 Information on test modes and additional testing requirements5 Additional guidance for testing host products is given in KDB Publication 996369 D04 Module Integration Guide. Test modes should take into consideration different operational conditions for a stand-alone modular transmitter in a host, as well as for multiple simultaneously transmitting modules or other transmitters in a host product.