User Manual

Copyright © 2001 Linear Corporation 218234 A
RSM-2
REMOTE SPEAKER/
MICROPHONE KIT
For Use With the Dual 824
Security System
Installation
Instructions
PRODUCT DESCRIPTION
The Model RSM-2 Remote Speaker/Microphone kit is designed
for use with Linear’s Model Dual 824 Security System. When a
Model VB-2 or VB-3 audio module is installed in the Dual 824
control panel, the RSM-2 speaker and microphone provide
sound and audio monitoring at the keypad.
The RSM-2 speaker mounts inside the DUAL 824KP keypad.
Four locking push-on washers secure the speaker to the keypad
case. The speaker will sound voice prompts for operating the
system from the VB-2 or VB-3 module installed in the DUAL 824
control panel. With the Model VB-2 installed, the Central Station
can talk to the subscriber through the RSM-2 speaker.
The RSM-2 microphone presses into a recess designed into the
keypad’s case. With the Model VB-2 installed into the DUAL 824
control panel, the Central Station can monitor sounds in the
installation. THE MODEL VB-3 AUDIO MODULE DOES NOT
SUPPORT AUDIO MONITORING AND DOES NOT REQUIRE
INSTALLATION OF THE MICROPHONE.
1. KIT COMPONENTS
2. OPEN KEYPAD 3. MOUNT SPEAKER & MICROPHONE 4. ROUTE WIRING
5. CONTROL PANEL CONNECTIONS 6. INSTALL VOICE BOARD 7. KEYPAD CONNECTIONS
8. VOICE SYNTHESIS SETUP 9. REMOTE SYSTEM OPERATION LINEAR LIMITED WARRANTY
This Linear product is warranted against defects in material and workmanship for twelve (12)
months. The Warranty Expiration Date is labeled on the product. This warranty extends only to
wholesale customers who buy direct from Linear or through Linear’s normal distribution channels.
Linear does not warrant this product to consumers. Consumers should inquire from their selling
dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the
part of Linear corporation for consequential damages arising out of or in connection with use or
performance of this product or other indirect damages with respect to loss of property, revenue,
or profi t, or cost of removal, installation, or reinstallation. All implied warranties, including implied
warranties for merchantability and implied warranties for fi tness, are valid only until Warranty
Expiration Date as labeled on the product. This Linear Corporation Warranty is in lieu of all other
warranties express or implied.
All products returned for warranty service require a Return Product Authorization Number (RPA#).
Contact Linear Technical Service at 1-800-421-1587 for an RPA# and other important details.
IMPORTANT !!!
Linear radio controls provide a reliable communications link and fi ll an important need in portable
wireless signalling. However, there are some limitations which must be observed.
• For U.S. installations only: The radios are required to comply with FCC Rules and Regulations
as Part 15 devices. As such, they have limited transmitter power and therefore limited range.
• A receiver cannot respond to more than one transmitted signal at a time and may be blocked
by radio signals that occur on or near their operating frequencies, regardless of code settings.
• Changes or modifi cations to the device may void FCC compliance.
• Infrequently used radio links should be tested regularly to protect against undetected
interference or fault.
• A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale
distributor or dealer, and these facts should be communicated to the ultimate users.
[phone] • FAX [phone]
USA & Canada [phone] & [phone]
Toll Free FAX [phone]
www.linearcorp.com
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,RSM-2,SPKR/MIC,DUAL 824 - LINEAR P/N: 218234 A- INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - SCALE: 1-1
TWIST SCREWDRIVER IN SLOT
TO OPEN KEYPAD CASE
RSM-2 SPEAKER
LOCATION
RSM-2
MICROPHONE
LOCATION
1 2
43
PLACE SPEAKER ON
MOUNTING POSTS
PRESS ON LOCKING
WASHERS
PLACE MICROPHONE
INTO MOUNTING HOLE
PRESS IN THE
MICROPHONE
WIRING
STRAIN-RELIEF
ZIP-TIE
WIRE
NUTS
MICROPHONE
SPEAKER
PUSH-ON
LOCK
WASHERS
ROUTE CABLES BETWEEN
THE CONTROL PANEL
AND THE KEYPAD
MAXIMUM RECOMMENDED
WIRE RUN IS 100 FEET
USE SHIELDED
TWISTED PAIR
FOR MICROPHONE
(BELDEN #9462 OR
GENERAL CABLE
#E2002S OR
EQUIVALENT)
USE 22 AWG
6-CONDUCTOR
CABLE FOR KEYPAD
AND SPEAKER
(WELCO #9209,
BELDEN # 9576,
OR GENERAL CABLE
#C4066 OR
EQUIVALENT)
KPD
+
KPD
-
KPD
CLK
KPD
DAT
KPD
SPK+
KPD
SPK -
KEYPAD
RED BLACK
ORANGE WHITE
DUAL 824KP
HARDWIRED KEYPAD
MODEL RSM-2
VOICE RESPONSE
SPEAKER
DUAL 824 TERMINALS
MIC #2
+
MIC
COM
MIC #1
+
VB-2 TERMINALS
MODEL RSM-2
VOICE RESPONSE
MICROPHONE
CABLE
SHIELD
CABLE
SHIELD
VB-2
DUAL 824
CAREFULLY PLUG VOICE MODULE
INTO THE TWO CIRCUIT BOARD SOCKETS
BE SURE ALL
PINS ARE ALIGNED
BOARD ARROWS
POINT UP
BE SURE CONTROL PANEL POWER IS DISCONNECTED!
SHIELDED
TWISTED PAIR
WIRE FOR
MICROPHONE
TWIST THE NEGATIVE
WIRE NUT CLOSE
TO END OF THE CABLE
TO KEEP THE SHIELD
FROM SHORTING
TO BOARD
6-CONDUCTOR
WIRE FOR KEYPAD
AND SPEAKER
CONNECT KEYPAD
AND SPEAKER
WIRES WITH
WIRE NUTS
ZIP-TIE WIRES
TO SPEAKER
MOVE JUMPER
TO PINS 2 & 3
TO SILENCE THE
KEYPAD BEEPER
PROGRAMMING STEP #78
ENTERS STEP NUMBER
1 FOR AUDIO ENABLE
STORES VALUE - 1 BING
SYSTEM ARMED
HOME MODE
PROGRAM THE SYSTEM TO
ENABLE AUDIO OUTPUT
FROM THE VOICE BOARD
SWITCH BETWEEN MODES TO
TEST THE AUDIO OUTPUT
ADJUST THE VOICE BOARD'S
VOLUME CONTROL TO SET
THE VOICE LEVEL

A B C
GHI
"
PRS
%
DEF
!
#
JKL
$
MNO
FROM A HOUSE PHONE FROM AN OUTSIDE PHONE
PRESS
ENTER A USER CODE THEN PRESS #
SYSTEM WILL REPORT MODE,
ALARMS, AND TROUBLE
PRESS "1" TO SWITCH
TO OFF MODE
PRESS "2" TO SWITCH
TO CHIME MODE
PRESS "3" TO SWITCH
TO HOME MODE
PRESS "4" TO SWITCH
TO AWAY MODE
PRESS "5" TO LISTEN
TO ALARM STATUS
PRESS "6" TO LISTEN TO
TROUBLE STATUS
PRESS "7" TO LISTEN
TO SENSOR STATUS
NOTE: THE SYSTEM
MUST BE CONNECTED
TO A TELEPHONE LINE
TO USE THESE FUNCTIONS
DIAL THE INSTALLATION; AFTER
TWO RINGS, HANG UP AND DIAL
THE INSTALLATION AGAIN THEN
LISTEN FOR THE TONE (THE
2ND CALL NEEDS TO BE 10-30
SECONDS AFTER 1ST CALL)
PRESS ANY OTHER KEY
EXCEPT # TO HANG UP
- OR -