(EN-2A4) (EN-2M7) EP-4xx / EP-736 EP Series User Programming Guide Document Number: 10028379 Rev-A or dial
Notices It is IMPORTANT that this instruction manual be read and understood completely before installation or operation is attempted. It is intended that the installation of this unit will be performed only by persons trained and qualified in the installation of access control equipment. The IMPORTANT safeguards and instructions in this manual cannot cover all possible conditions and situations which may occur during installation and use.
Contents 1. Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . 2 General Features. . . . . . . . . . . . . . . . . . . . . . . . . . 2 System Information. . . . . . . . . . . . . . . . . . . . . . . . 2 FTP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SMTP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Time Server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . User Data Export. . . . . . . . . . . . . . . . . . . . . . . . .
1. Introduction This manual contains information regarding the programming and configuration of the EP Series access control system. The system offers multi-station ability to secure doors, manage access of personnel, create and analyze reports, and monitor the system remotely from any Web browser. All monitored activity at the facility is recorded in the system memory — providing a record of all Card Holder entries and exits, input detection, and security or fire detection, if desired.
2. Software Layout System Server Software The Controller browser interface includes two methods available to the operator for programming and navigation. These methods include using the Toolbar and Wizard. The Toolbar provides access to all configuration options, whereas the Wizard provides access to the core system components. The following illustration shows the location of the Toolbar and Wizard icon. Tool Bar Wizard Icon The first time the system is run, the Wizard will run automatically.
Toolbar Menu The Toolbar provides access to all setup, programming, management, and reporting options of the Controller. Administration: Add, edit, or delete Card Holders, card formats and Access Levels, badge layouts and templates. Schedule: Add and edit time schedules, holidays, and unlock schedules. Events: Create events that are assigned to actions. For example, a time schedule can be assigned to an auxiliary output.
4. Using the Wizard The Wizard allows the user to configure the basic settings of the system. Advance through each setting by clicking the Next button. The Wizard will launch automatically the first time the system is run. Visit the Wizard at any time by clicking the icon in the lower left corner of the window. Exit the Wizard Click Next to Advance Wizard Icon »» NOTE: When programming various elements of the system, do not use the same name for multiple items (e.g., use Door 1, Door 2, etc.).
Language Use Language to select the country and language where the system will be located. Click Next to advance. License License displays the basic system information of the Controller. Please print the License Key for future needs or in case of a factory default. Click Next.
Card Format Card Format displays the default card formats of the system. The system includes several pre-configured card formats. If the desired card format is listed, click Next to advance to the next Wizard item. If the desired card format is not listed, click New to enter the format information and click Add. »» NOTE: It is recommended to delete card formats that are not in use.
Holiday Group Use Holiday Groups to define days and times during the year when holiday hours are used. When the holiday starts, the Controller switches from regular hours to holiday hours. When the holiday ends, the regular hours resume. You can assign four holiday groups with up to 30 holidays total among the groups. A holiday can include any number of consecutive days within the same calendar year.
Schedules A Schedule is a combination of a time interval and one or more days of the week. Use schedules to identify the hours and days when inputs, outputs or door access are in operation. Assign holiday groups to the schedule to control when operations occur on holidays. There is one default time schedule of Always, which is defined as 00:00-23:59, seven days per week. Adding a Schedule 1. Click New. 2. Enter the desired name and description (optional) for the schedule. 3.
Doors Displays the Doors that are assigned to the system. Click on the door name to view or edit each door. Editing a Door Select the desired door. Scroll to the bottom of the page and click Edit. After making any edits, be sure to click Save at the bottom of the page. Basic 1. Enter the desired Name and Description (optional) for the door. 2. For multi-floor installations, select the Floor. Reader 1. In the Reader section, select the settings for the door’s reader. Door Contact 1.
Doors (Cont.) Door Lock Mode 1. Choose a Door Lock Name to name the lock for logging. Normal 2. Configure Door Lock Mode as Door Lock Mode follows: • Normal: Lock activates in response to a valid access request and REX unlocks door for exit. • Locked: Does NOT grant access in Man-Trap response to REX, card or code. Door Lock Mode • Locked w/REX: Remains in locked mode, ONLY REX will activate lock. • Unlocked: Door will remain unlocked at ALL times.
Doors (Cont.) Door Status Alarm Output Sets the actions of a door contact on the door. The door contact must be enabled to use these functions. 1. Check Forced Door to trigger the door alarm output if the door opens, but no access was granted. 2. Check Held Door to trigger the door alarm output if the door is held open longer than the Held Open Time. 3. Select Energized or De-energized for the Default State of the Door Status Alarm Output. 4. Select an Output to use for the Door Status Alarm Output. 5.
Doors (Cont.) First Man In Rule First Man in Rule unlocks a door when first Card Holder enters. 1. Check Enable to use a First Man In Rule. 2. Select a Grace Period to allow the selected first man Card Holder(s) access minutes before a scheduled start time. 3. Select up to three time Schedules for the rule to be active. 4. Select the Type of Card Holders (individual or group). 5. Search or choose Card Holder(s) or Groups for the rule. Use the arrows to move the name(s) in and out.
Access Levels An Access Level establishes which doors the Card Holder can access and when they are allowed to access them. Access Levels are comprised of a time schedule and door(s). Adding an Access Level 1. 2. 3. 4. Click New. Enter the Access Level name. Assign a time schedule to the Access Level by choosing it from the drop-down menu. For Door List select the desired doors (or use the search icon to find a specific door) and click the right arrow to move the doors to the field on the right. 5.
Resident Use Resident to enter card users in the database. To Add a Card Holder Individuals who enter the facility are entered in the system as Card Holders. Creating a Card Holder Click New to enter a Card Holder 1. Click New. 2. Enter the name and contact information of the Card Holder. 3. A phone number is required for the resident to be listed on the display panel.
Card Holder (Cont.) Card Holder Options 1. Select ADA Timing for extended timing for the door relay. 2. Select Exempt to allow the Card Holder to bypass Anti-Passback rules (except occupancy rules) if the Card Holder is allowed access to the region. 3. Select a Web User Account to give the Card Holder operator privileges to the server software. 4. Choose the highest Threat Level that the Card Holder will be allowed access.
Card Holder (Cont.) Card Status 1. Select the card’s current status. Card Type 2. Select the function for the card with card type dropdown. Select the card status Access Level 3. For Select Type select Individual or Group access level. 4. For Select Level select the desired access levels (or use the search icon to find a specific access level) and click the right arrow to move the access level to the field on the right. Activation Date 5.
Card Use Card to enter card numbers in the database and assign the card to a Card Holder. Assigning a Card to a Card Holder 1. Select the Card Holder from the main window. 2. Click Add Card. 3. If using Card Scan, select the door where the card will be scanned. 4. Select the appropriate Card Format from the drop-down. 5. Enter the Card Number of the card. 6. If using Card Scan, click the button and present the card to the reader. The card number will populate the Card Number field. 7.
Network Enter the Network configuration information as provided by the IT administrator. DHCP assigns an IP address to the Controller automatically on a network containing a DHCP Server (a router will typically have a built-in DHCP Server). When Static is selected, options IP Address, Subnet Mask, Gateway must be entered. DNS is an Internet service that translates domain names into IP addresses. The IP address of a DNS is required if using NTP time server or SMTP e-mail. Editing Network Settings 1.
Start Save Start Save is the command to save the initial settings for the system and select which page appears on login. Editing Startup Page • Default Page: Use the dropdown selector to choose the page that the system will display upon login. • Save to SD Card: Leave this box selected to save the startup information to the SD card. Un-check to save the startup information to the Controller’s memory.
3. System Programming Connect to the Controller Open a web browser on a local computer and enter the IP address of the Controller (Default = 192.168.0.250). The browser presents the login page as shown. 1. Enter the User ID. • Default User ID = admin 2. Enter the Password. • Default Password = admin 3. Click Login. Just in case, a link is displayed to send a message to the EP Series Super Administrator for a forgotten password.
Card Holder Card Holders are individuals who access the facility and are entered in the system. Access credentials are assigned to Card Holders. There are 3 main Card Holder functionalities that are required for the system to work properly. Administration 1. 2. 3. 4. Fill in your personal information. Enter your First and Last name (required). Enter your phone number (required). Enter your email. The Card Card Enrollment must be completed for a card to be used on the system. To activate a card: 1.
Card Holder (Cont.) Certain features are available to address variable resident needs. Do Not Disturb The Do Not Disturb option can be used to temporarily prevent the resident’s listing to appear on the panel directory. 1. Check the Do Not Disturb check box. 2. Click Save. Unchecking the box will return the resident’s phone number to the directory listing. Vacation When residents go on vacation, their profile can be set to Vacation Mode.
Card Holder (Cont.) Assigning a Card to an Existing Card Holder Click Add Card 1. Select the Card Holder from the main window. 2. Click Add Card. Card Format 3. Select the appropriate Card Format from the drop-down field. Choose the Card Format Card Number 4. Enter the Card Number, or use the Auto Scan feature. Auto Scan 5. Choose the Auto Scan door reader where the card will be presented. »» NOTE: Card scanner can only be used with doors 1 - 4. 6.
Card Holder (Cont.) Access Level 1. For Select Type select Individual or Group access level. 2. For Select Level select the desired access levels (or use the search icon to find a specific access level) and click the right arrow to move the access level to the field on the right. Use Arrows to Choose Levels Activation Date 3. Choose an optional activation and expiration date for the card. 4. Click Save to assign the card to the Card Holder. The added card will show on the card list for the Card Holder.
Card Format Card Format displays the default card formats of the system. The system has several pre-configured card formats. If the desired card format is not listed, a custom format may be added. Adding a Card Format 1. Click New. 2. Enter a name and description (optional) for the card format. 3. Enter the facility code bit/length, card number bit/length and parity information as provided by the card manufacturer. 4. Click Add to save the changes.
Access Level An Access Level establishes which doors the Card Holder can access and when they are allowed to access them. Access Levels are comprised of a time schedule and door(s). Adding an Access Level 1. Click New. 2. Enter the desired Access Level Name and Description (optional). 3. Assign a time schedule to the Access Level by choosing it from the Schedule dropdown menu. 4. Select Group or Individual for the Access Group Type. 5.
Schedule A Schedule is a combination of a time interval and one or more days of the week. Use schedules to identify the hours and days when inputs, outputs or door access are in operation. Assign holiday groups to the schedule to control when operations occur on holidays. There is one default time schedule of Always, which is defined as 00:00-23:59, seven days per week. Adding a Schedule 1. Click New. 2. Enter the desired name and description (optional) for the schedule. 3.
Holiday Use Holiday to define days and times during the year when holiday hours are used. When the holiday starts, the Controller switches from regular hours to holiday hours. When the holiday ends, the regular hours resume. You can assign four holiday groups with up to 30 holidays total among the groups. A holiday can include any number of consecutive days within the same calendar year.
Unlock Schedule An Unlock Schedule defines which Schedule will be used with selected access devices to automatically unlock one or more doors. Adding an Unlock Schedule 1. Click New. 2. Enter a Unlock Schedule Name. 3. Select the Schedule when the door will be unlocked. 4. Click the Select Type drop-down to select an individual door or a group of doors. 5.
One Time Unlock Schedule A One Time Unlock Schedule defines one date and time to automatically unlock one selected door. Adding a One Time Unlock Schedule 1. Click New. 2. Enter a Name for the One Time Unlock Schedule. 3. Select the Date when the door will be unlocked. 4. Select the Start Time and End Time for the unlock period. 5. Click the drop-down to select a door to unlock. Click Add to create the One Time Unlock Schedule.
Event Action Event Action allows the operator to create events that are assigned to actions. For example, the operator may assign a time schedule to an auxiliary output. Adding an Event Action 1. Click New and enter a name and description. 2. In the Basic section, name the event, fill in a Description, and select a Schedule for the time the Event Action will be active. To Add an Event Action Click New Event 3. In the Event section, click Insert to add a new event. 4.
Event Code Event Code lists the events that are available to the operator. The user can configure the event to display in the Dashboard and/or require the operator to acknowledge the event. Selecting Event Codes 1. On the Event Code list, edit the checkboxes for the events codes that will display on the dashboard if they occur. 2. On the Event Code list, edit the checkboxes for the events codes that will require operator acknowledgment if they occur.
Threat Level Optional Feature Threat Levels are used in systems to modify existing unlock schedules and Access Level privileges. The system has five predefined Threat Levels. The names of each can be changed to match installation requirements. Current Threat Level Setting 1. Click Edit to change or disable the Threat Level. 2. Uncheck the Turn Off Threat Level checkbox to enable Threat Levels. 3. Use the Threat Level drop-down menu to select a Threat Level. 4. Click Save.
Threat Level Setting Optional Feature There is a three tier hierarchy of Threat Levels to consider when configuring an system. First the System Threat Level, second the Door Threat Level and third the Card Holder Threat Level. See the Door and Card Holder sections for details on setting the Door and Card Holder Threat Levels. System Threat Level Setup 1. Click Edit to change the number or title of the Threat Levels. 2.
Door Door displays the doors that are assigned to the system. Click on the door name for additional information pertaining to each door. »» NOTE: When programming various elements of the system, do not use the same name for multiple items (e.g., use Door 1, Door 2, etc.). »» NOTE: Do not use special characters (<>’?.”;!@#$%^&*()_-+={}:[]\|/). Editing a Door Select the desired door. Scroll to the bottom of the page and click Edit. After making any edits, be sure to click Save at the bottom of the page.
Door (Cont.) Door Lock Mode 1. Choose a Door Lock Name to name the lock for logging. Normal 2. Configure Door Lock Mode as Door Lock Mode follows: • Normal: Lock activates in response to a valid access request and REX unlocks door for exit. • Locked: Does NOT grant access in Man-Trap response to REX, card or code. Door Lock Mode • Locked w/REX: Remains in locked mode, ONLY REX will activate lock. • Unlocked: Door will remain unlocked at ALL times.
Door (Cont.) Door Status Alarm Output Sets the actions of a door contact on the door. The door contact must be enabled to use these functions. 1. Check Forced Door to trigger the door alarm output if the door opens, but no access was granted. 2. Check Held Door to trigger the door alarm output if the door is held open longer than the Held Open Time. 3. Select Energized or De-energized for the Default State of the Door Status Alarm Output. 4. Select an Output to use for the Door Status Alarm Output. 5.
Door (Cont.) First Man In Rule First Man in Rule unlocks a door when first Card Holder enters. 1. Check Enable to use a First Man In Rule. 2. Select a Grace Period to allow the selected first man Card Holder(s) access minutes before a scheduled start time. 3. Select up to three time Schedules for the rule to be active. 4. Select the Type of Card Holders (individual or group). 5. Search or choose Card Holder(s) or Groups for the rule. Use the arrows to move the name(s) in and out.
Aux Input Aux Input displays the inputs that are assigned to the system. Click on the input name to view or edit the settings of the input. Editing an Input 1. Select the desired input and click Edit. 2. Enter a desired Name and Description (optional) for the input. 3. Assign the input to a Floor for viewing on the Dashboard. 4. Select the appropriate Input Type for the input. This setting will be determined by the wiring and type of switch connected to the input (NC or NO, supervised or unsupervised). 5.
Aux Output Aux Output displays the outputs that are assigned to the system. Click on the output name to view or edit the settings of the output. Editing an Output 1. Select the desired output and click Edit. 2. Enter a desired Name and Description (optional) for the output. 3. Configure the Mode of the output: • Single Pulse: Output latches in response to a valid event for the time entered. • Repeating: Output opens and closes in a cycle for the time entered.
Controller Controller displays information pertaining to each system Controller. Click on the Controller name on the list to view or edit information. Editing the Controller Info 1. Select the Controller and click Edit. 2. Enter a desired name and location (optional). 3. Select the appropriate Tamper Input value. This will be determined by the wiring configuration of the input. 4. Select the appropriate Power Fault Input value. This will be determined by the wiring configuration of the input. 5.
User Defined Field User Defined Fields are 20 custom data fields that can be assigned to a Card Holder profile. This field can be used for employee ID or other specific information unique to a Card Holder. Editing User Defined Fields 1. Click Edit to enter user defined fields. 2. Enter any custom data in the 20 User Info fields. 3. Click Save when finished.
User Role User Roles define the access privilege of the operators. A User ID is assigned to each person who will work with the Controller. Each User ID can be configured to have different system privileges. System privileges determine the options the user has available in the Controller browser interface. Setting User Roles 1. Select the User ID to edit and click Edit. 2. Enter the options and name for the Basic settings. 3. Select the Administration options that will be available for the user. 4.
Web User Account Create or edit the Web User Accounts that are used to log into to the Controller. Adding or Editing a Web User 1. To add a new Web User, click New. To edit an existing Web User, click Edit. 2. Enter the User ID, Password and Web User Name of the new user. 3. Assign a User Role, which defines the privilege level of the user account. 4. Enter the Language and Default Page for the user. 5. Assign the Default Floor and enable Floor Show if the floor graphic will display to the user. 6.
Backup Backup enables the system backup and defines the backup device, time and location of the backup. The system automatically assigns a name to the backup at the time of the backup with the following format: • • • • • • • YYYYMMDDHHMMSS YYYY = 4-digit year MM = 2-digit month DD = 2-digit day HH = 2-digit hour MM = 2-digit minutes SS = 2-digit seconds Scheduled Backup 1. To change the backup settings, click Edit. 2. Set a log name for the backup in the Name field. 3.
Save & Reboot Save and Reboot the system. Reboot 1. Click Reboot to force a data save on the Controller and restart the system. 2. Enter an super administrator password and click OK. »» NOTE: Without battery backup, if the system is powered down prior to saving data, data will be lost. The EP series performs an automatic backup every 1.5 hours and/or upon A/C loss when on battery to permanent memory.
IP Address The Internet Protocol (IP) Address area sets all of the network settings including the IP Address, Subnet Mask, Gateway Address, DNS Server 1, DNS Server 2, and HTTP Port. DHCP assigns an IP address to the Controller automatically on a network containing a DHCP Server (a router will typically have a built-in DHCP Server). When Static is selected, options IP Address, Subnet Mask, Gateway must be entered. DNS is an Internet service that translates domain names into IP addresses.
FTP File Transfer Protocol (FTP) enables and configures the system to backup to an FTP location. Enter FTP information as provided by your web host. Editing FTP Settings 1. Check the Enable checkbox to enable an FTP server connection. 2. Enter the IP address of the FTP server in the Server Address field. 3. Enter the communications port number into the Server Port field. 4. Enter the FTP server user name into the Server ID field. 5. Enter the FTP server password into the Server Password field. 6.
SMTP Simple Mail Transfer Protocol (SMTP) provides the ability to send email to specified email addresses. Editing SMTP Settings 1. To allow the Controller to send SMTP e-mail messages, check the Use SMTP Service checkbox. 2. Enter the SMTP mail server URL (typically “mail.your email domain. com”) the the SMTP Server field. 3. Enter the incoming port number of the SMTP mail server in the Port field. 4. Enable TLS if your mail server uses secure server communication (this is common).
Time Server Time Server provides the ability to sync the system to a time server or manually set the time. »» NOTE: Gateway IP and DNS IP addresses must be configured to access public time servers. Refer to IP Address to configure these settings. Editing Time Server Settings 1. To manually set the system time select Manual Time Setting. Skip to Step 6. 2. To use a time server, select NTP Server Synchronization. 3. Select one of the time servers from the Server Address drop box. 4.
User Data Import User Data Import provides the ability to import Card Holder data from a comma separated value (CSV) file. To successfully import a file, the column headers must match those present in the User Data Export file. It is suggested to perform a data export and use it as a template for the import file. You must have the related card formats and Access Levels configured before importing the file. »» WARNING: Do not use special characters (<>’?.”;!@#$%^&*()_-+={}:[]\|/) in any fields.
Log Log displays the most recent events for quick viewing. Viewing the Log 1. When Log is selected, the log displays on the screen. 2. Click the page number or arrows at the bottom of the screen to display other pages of the log. Printing the Log 3. To print out the log, click Print.
1. Log Report The Log Report allows the operator to create a customized report of system, network and Controller events. Customizing the Log Report 1. Select the database to search, either Current DB, User PC, or SD Card. 2. Select beginning and ending Log Date for the search. 3. Select the general events to search for with the Log Type checkboxes. 4. Search for a particular device by checking the Device Name checkbox and enter the device name. 5.
Log Management Log Management allows the operator to create a backup of all log events. The backup can be scheduled and directed to the SD card on the Controller or an FTP location. The backup can also be manually generated to a CSV or DB file. Automatic Log Backup 1. Enter the percentage of log fullness to trigger a pop up message or automatic log backup. 2. The message displayed can be edited in the Pop Up Message field. 3. Enter a name for the backup in the Name field. 4.
Report Report allows the operator to view and print or save a report of items in the system’s memory. The report is created using Filters. Items that match the filters entered will be included in the report. Running a Report 1. Use the Table Name dropdown to select which area of system memory to generate a report from. »» NOTE: The remaining filter options will vary depending on the Table Name selected. Doors, Elevators, Aux In & Out • Select the filters for the report.
Access Report The Access Report allows the user to generate reports for all access events that occur at any door or elevator. Running an Access Report 1. Select Door or Elevator for the Type to search for. 2. Select the starting and ending date range for the search in the Date fields. 3. Select the Door, Card Holder, and Access Level to search for in the Condition fields. 4. To generate the report, click Search. 5. To print the report, click Print. 6. To export the report as a file, click CSV.
System Report The System Report displays the current memory allocation of the database. The report runs when System Report is selected.
Card Holder Group A Card Holder Group contains individual Card Holders for the purposes of common access and reporting. Adding a Card Holder Group 1. Click New. 2. Enter the Card Holder Group Name. 3. For Card Holder List, select the desired card holders (or use the search icon to find a specific card holder) and click the right arrow to move them to the field on the right. »» NOTE: Ctrl-click or shift‑click will select multiple Card Holders. 4. Click Add to save the changes.
Door Group The Door Group allows individual doors to be combined in groups. The group can then be added to an Access Level for simpler management. Adding a Door Group 1. Click New. 2. Enter the desired door Group Name. 3. For Door List, select the desired doors (or use the search icon to find a specific door) and click the right arrow to move the doors to the field on the right. »» NOTE: Ctrl-click or shift-click will select multiple doors. 4. Click Add to save the changes.
Access Level Group Add individual Access Levels to Access Level Groups. These groups can then be assigned to cards in the Card Holder section. Adding an Access Level Group 1. Click New. 2. Enter the desired Group Name. 3. For Access Level List, select the desired access level (or use the search icon to find a access level) and click the right arrow to move the access levels to the field on the right. »» NOTE: Ctrl-click or shift-click will select multiple Access Levels. 4. Click Add to save the changes.
Client Management Optional Feature Client Management allows the user to enable/disable, connect/disconnect, and update client Controllers associated to the main Controller’s server database. Client Management allows user to update the firmware of the clients. The firmware for an individual Controller may be updated by clicking the Update Client button for the Controller. If multiple Controllers are connected to a main Controller, the Update All will update all the clients.
Client Replacement Optional Feature Client Replacement is used when an existing client Controller is replaced with a new client Controller. Replace a Client 1. Power off bad Client board and disconnect from network. At the Dashboard the Door and Aux icons are grayed out. 2. Install replacement Client board on the network and set the IP to the same address as the bad client. 3. Save the MAC address of the new client. »» NOTE: Leave the Server address set to 0.0.0.0 4.
Logout Logout prevents unauthorized persons from working in the system but still allows all access control operations to continue. To secure the system, be sure to logout when finished. Logging Out of the Controller 1. When ready to exit, click Logout. 2. The Controller will logout the user and return to the Login screen.
5. Site Map The Site Map is an overview of the pages within the Controller interface. Each page listed in the site map is linked to the page it represents. This allows the user to quickly jump to any section listed in the site map.
6. Lost Card Lost Card is a utility to quickly identify the Card Holder associated with a lost card. The operator may enter any card number to view the Card Holder that is associated with the card, reset a One Time Card, or override a Violation Grace.
7. License License displays the basic system information of the Controller. Please print the License Key for future needs or in case of a factory default. »» NOTE: You can use the MAC address to recover the license key for the system. Visit http://www.e3upgrade.com and enter the MAC address and follow the directions. License Button Press + to View System Info System Information • Press the + sign to display the system configuration information and upgrade options.
8. End User License Agreement IMPORTANT: THIS SOFTWARE END USER LICENSE AGREEMENT (“EULA”) IS A LEGAL AGREEMENT BETWEEN YOU (EITHER AN INDIVIDUAL OR, IF PURCHASED OR OTHERWISE ACQUIRED BY OR FOR AN ENTITY, AN ENTITY) AND NORTEK SECURITY & CONTROL LLC. READ IT CAREFULLY BEFORE USING THE SOFTWARE. IT PROVIDES A LICENSE TO USE THE SOFTWARE AND CONTAINS WARRANTY INFORMATION AND LIABILITY DISCLAIMERS.
1. Nations Convention on the International Sale of Goods. This EULA contains the complete agreement between the parties with respect to the subject matter hereof, and supersedes all prior or contemporaneous agreements or understandings, whether oral or written. You agree that any varying or additional terms contained in any purchase order or other written notification or document issued by you in relation to the Software licensed hereunder shall be of no effect.
Appendix A: Directory Segmentation Objective: • In case of multiple networked TE units with displays (say TE1, TE2 and TE3), residents can be assigned to be displayed on one or more TE units. • This distribution or “segmentation” is done using the Access Level assigned to the Entry Code associated with each Resident. The reasons is that there can be only one Entry code assigned per Resident. Steps to implement Directory Segmentation: 1.
Assign a Directory Code, and check (P) the Directory Listed check box. 3. Select an appropriate Access Level, based on which TE unit the Resident should be displayed on, Typically, a Resident will only be listed on one TE unit’s directory. 3.1. Note: An Entry code with appropriate Access Level is a MUST for the residents to be listed on any directory.
These pages in EP Series User Programming Guide 72
ntentionally left blank.
or dial Copyright © 2019 Nortek Security & Control LLC 10028379 Rev-A
