Installation Instructions

MT-1, MT-2
DIGITAL
TRANSMITTERS
Installation
Instructions
DESCRIPTION
The MegaCode series of digital transmitters are
wireless radio controls designed for use with
MegaCode format receivers. The MegaCode radio
format provides unparalleled security. The system
can be programmed to more than a million different
codes.
Each transmitter is pre-set at the factory to one of over
1,000,000 codes. The receiver is programmed by
sending a signal to it from the transmitter(s) that is
going to be used with it. This stores the transmitter’s
code into the receiver’s memory. The receiver will
retain its memory even without power. The receiver
will activate only from these “memorized”
transmitters. Please refer to the receiver’s
instructions for maximum transmitter capability.
PROGRAM TRANSMITTER INTO RECEIVER
Refer to the instructions provided with the receiver
to program transmitters into receiver’s memory.
Some receivers that accept “Block Coding” can be
programmed to accept a user defined block of ID
codes. Transmitter Models MT-1B and MT-2B are
block coded at the factory.
REPLACE BATTERIES
The battery should last 12 to 18 months with normal
use. The red LED on the face of the transmitter will
glow when the unit is activated. When the red LED
lights dimly, or not at all when transmitting, the battery
needs to be replaced. Remove the battery access
door to change the battery. Any type of 9-volt battery
can be used.
LIMITED WARRANTY
This Linear product is warranted against defects in material
and workmanship for twelve (12) months. The Warranty
Expiration Date is labeled on the product.
This warranty
extends only to wholesale customers
who buy direct from
Linear or through Linear’s normal distribution channels.
Linear does not warrant this product to consumers.
Consumers should inquire from their selling dealer as to the
nature of the dealer’s warranty, if any.
There are no
obligations or liabilities on the part of Linear Corporation
for consequential damages arising out of or in
connection with use or performance of this product or
other indirect damages with respect to loss of property,
revenue, or profit, or cost of removal, installation, or
reinstallation.
All implied warranties, including implied
warranties for merchantability and implied warranties for
fitness, are valid only until Warranty Expiration Date as
labeled on the product.
This Linear Corporation Warranty
is in lieu of all other warranties express or implied.
All products returned for warranty service require a Return
Product Authorization Number (RPA#). Contact Linear
Technical Services at 1-800-421-1587 for an RPA# and other
important details.
IMPORTANT !!!
✴
Linear radio controls provide a reliable communications link
and fill an important need in portable wireless signaling.
However, there are some limitations which must be observed.
✴
For U.S. installations only: The radios are required to comply
with FCC Rules and Regulations as Part 15 devices. As such,
they have limited transmitter power and therefore limited
range.
✴
A receiver cannot respond to more than one transmitted signal
at a time and may be blocked by radio signals that occur on
or near their operating frequencies, regardless of code
settings.
✴
Changes or modifications to the device may void FCC
compliance.
✴
Infrequently used radio links should be tested regularly to
protect against undetected interference or fault.
✴
A general knowledge of radio and its vagaries should be
gained prior to acting as a wholesale distributor or dealer, and
these facts should be communicated to the ultimate users.
Copyright © 2000 Linear Corporation 212999 B
INSTR,MT-1&MT-2 Linear P/N: 212999 B Ink: Permanent Black Material: 20 lb. Mead Bond Size: 7.000" X 5.000" Scale: 1-1
ROTATE CLIP
AWAY FROM
BATTERY
DOOR
REMOVE BATTERY
DOOR TO REPLACE
BATTERY
REMOVE VISOR
CLIP BY REMOVING
SCREW
[phone] • FAX [phone]
USA & Canada [phone] & [phone]
Toll Free FAX [phone]
www.linearcorp.com
RED INDICATOR
LIGHTS WHEN
TRANSMITTING
PRESS BUTTON
TO SEND CODE 1
RED INDICATOR
LIGHTS WHEN
TRANSMITTING
PRESS LEFT BUTTON FOR CODE 1
PRESS RIGHT BUTTON FOR CODE 2