USER MANUAL KA20IC2 system To learn more about LINAK, please visit: www.linak.
Page 2 of 23
Contents Preface.................................................................................................................................................. 4 Important information....................................................................................................................... 5 Safety instructions.............................................................................................................................. Before installation, reinstallation or troubleshooting....
Preface Dear User, We are delighted that you have chosen a product from LINAK®. LINAK systems are high-tech products based on many years of experience in the manufacture and development of actuators, electric control boxes, controls and chargers. This User Manual does not address the end-user. It is intended as a source of information for the manufacturer of the equipment or system only, and it will tell you how to install, use and maintain your LINAK electronics.
Important information Important information on LINAK® products can be found under the following headings: Warning! Failure to comply with these instructions may result in accidents involving serious personal injury. Failing to follow these instructions can result in the product being damaged or being destroyed. Safety instruction General Safe use of the system is possible only when the operating instructions are read completely and the instructions contained are strictly observed.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation • Statement – for all intentional and unintentional radiators: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
- Reorient or relocate the receiving antenna. - Increase the separation between the equipment and the receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/ TV technician for help. This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s).
Before installation, de-installation or troubleshooting: • Stop the KA20IC2. • Disconnect the power supply • Relieve the KA20IC2 of any loads, which may be released during the work. Before start-up: • Make sure that the system has been installed as instructed in this User Manual. • Make sure that the voltage is correct before the system is connected to the mains. (See KA20IC2 label in the appendix). • System connection. The individual parts must be connected before connecting to the mains.
Only for EU markets This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
Informations importantes Les informations importantes sur les produits LINAK® peuvent être trouvées dans les rubriques suivantes: Attention! Le non respect de ces instructions peut entraîner des accidents impliquant des blessures graves. Ne pas suivre ces instructions peut entraîner l´endommagement ou destruction du produit. Consignes de sécurité Géneral Le non respect de ces instructions peut entraîner des accidents impliquant des blessures graves.
Avant l´installation, ré-installation ou le dépannage: • Arrêtez KA20IC2 • Retirez la prise du secteur • Soulagez KA20IC2 des toutes charges qui pourraient être émises lors de l´utilisation Avant de démarage: • Assurez-vous que le système a été installalé comme indiqué dans le mannuel d´utilisateur. • Assurez-vous que la tension du boîtier de contrôle est correcte avant que le système soit connecté sur le secteur. • Système de connection.
Seulement pour les marchés au sein de l´UE: Cet appareil peut-être utilisé par des enfants âgés de 8 ans et plus, ainsi que les personnes dont les capacités physiques, sensorielles ou mentales sont réduites ou ayant un manque d´expérience et de connaissance si elles ont bénéficié d´une surveillance ou d´instructions concernant l´utilisation de l´appareil en toute sécurité et compris les risques encourus. Les enfants ne doivent pas jouer avec l´appareil.
Repairs In order to avoid the risk of malfunction, all KA20IC2 repairs must only be carried out by authorised LINAK workshops or repairers, as special tools must be used and special gaskets must be ftted. KA20IC2 under warranty must also be returned to authorised LINAK workshops.
Misc. on the KA20IC2 system This system is a KA20IC2 system developed for leisure beds and for indoor use in private homes. Warranty There is 36 months’ warranty on the KA20IC2 product against manufacturing faults calculated from the production date of the individual products (see label). LINAK A/S’ warranty is only valid in so far as the equipment has been used and maintained correctly and has not been tampered with. Furthermore, the system must not be exposed to violent treatment.
KA20IC2 - Start-up (How to pair Bluetooth connection) It is possible to pair multiple devices to the KA20IC2 via Bluetooth® . See following instructions: 1. Pairing your control Connect the KA20IC2 to the mains using the SMPS. Now the KA20IC2 will be in pairing mode in 3 minutes and the Under Bed Light will blink to indicate this. Take you hand control and press the 2 top buttons at the same time. Now the light will give a long blink and indicate that the control and the KA20IC2 are paired up.
3. Pairing another device later If you wish to connect another control or a smartphone/tablet to the KA20IC2 later, just disconnect, wait 2 minutes and connect the KA20IC to the mains to get it in pairing mode again. See instructions 1 or 2 above to find out how to pair the device, you want. The KA20IC will be in pairing mode every time the system has been out of power and connects again. To get the system out of pairing mode – simply press any button on an already paired device.
Functional description Hand Control HB10BL: Up – down back motor Up – down leg motor Common operation up/down (option) Light Button Hand Control HC05BL: Up – down back motor Up – down leg motor Common operation up/down (option) Light Button Hand Control HC10BL: Up – down back motor Up – down leg motor Common operation up/down (option) Light Button Hand Control HC20BL: Up – down back motor Up – down leg motor up to 3 extra channels Common operation up/down (option) Memory positions (3 positions) Store
Label for KA20IC Label for HB10 Label for HC05 Label for HC10 Label for HC20 Page 18 of 23
Disposal of LINAK products As LINAK customers often ask us how our products can be disposed of or scrapped we have prepared this guidance that enables a classification to different waste fractions for recycling or combustion. Guidance We recommend to disassemble our product into as many fractions as possible at the disposal and try to make it recycable. As examples of main groups within waste fractions we can mention: Metal, plastic, cable shoe, combustible waste and collection for recovery.
Main groups of disposal Product main groups Scrap Cable scrap Electronics scrap Plastic recycling or combustin X X X X HB10BL X X HC05BL X X HC10BL X X HC20BL X X KA20IC Comments Disposal of batteries Details regarding safe disposal of used and leaking batteries: Batteries should be disposed in accordance with appropriate federal, state and local regulations. LINAK recommends that used or leaking batteries are disposed through the local recycling system.
HB10BL Hand Control 47 140 14 Drawing No.: HC05 HC05BL Hand Control 13.5 100 2.9 34 1.
LINAK APPLICATION POLICY The purpose of the application policy is to define areas of responsibilities in relation to applying a LINAK product defined as hardware, software, technical advice, etc. related to an existing or a new customer application. LINAK products as defined above are applicable for a wide range of applications within the Medical, Furniture, Desk, and Industry areas.
FACTORIES CHINA LINAK (Shenzhen) Actuator Systems, Ltd. Phone: +86 755 8610 6656 Fax: +86 755 8610 6990 E-mail: sales@linak.cn www.linak.cn DENMARK LINAK A/S - Group Headquarters, Guderup Phone: +45 73 15 15 15 Fax: +45 74 45 80 48 Fax: +45 73 15 16 13 (Sales) E-mail: info@linak.com www.linak.com SLOVAKIA LINAK Slovakia s.r.o. Phone: +421 51 75 63 414 Fax: +421 51 75 63 410 E-mail: jp@linak.sk www.linak.com USA LINAK U.S. Inc.