USER MANUAL TWINDRIVE ® TD4 To learn more about LINAK, please visit: www.linak.
Contents Preface.................................................................................................................................................. 4 Important information....................................................................................................................... Safety instructions.............................................................................................................................. Before installation, reinstallation or troubleshooting......
Preface Dear User, We are delighted that you have chosen a product from LINAK®. LINAK systems are high-tech products based on many years of experience in the manufacture and development of actuators, electric control boxes, controls and chargers. This User Manual does not address the end-user. It is intended as a source of information for the manufacturer of the equipment or system only, and it will tell you how to install, use and maintain your LINAK electronics.
Important information Important information on LINAK® products can be found under the following headings: Warning! Failure to comply with these instructions may result in accidents involving serious personal injury. Failing to follow these instructions can result in the product being damaged or being destroyed. Safety instruction General Safe use of the system is possible only when the operating instructions are read completely and the instructions contained are strictly observed.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation • Statement – for all intentional and unintentional radiators: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
- Reorient or relocate the receiving antenna. - Increase the separation between the equipment and the receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/ TV technician for help. This device complies with Industry Canada licence-exempt RSS standard(s).
Before installation, de-installation or troubleshooting: • Stop the TD4. • Disconnect the power supply or pull out the mains plug. • Relieve the TD4 of any loads, which may be released during the work. Before start-up: • Make sure that the system has been installed as instructed in this User Manual. • Make sure that the voltage is correct before the system is connected to the mains. (See TD4 label in the appendix). • System connection. The individual parts must be connected before connecting to the mains.
Only for EU markets This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
Informations importantes Les informations importantes sur les produits LINAK® peuvent être trouvées dans les rubriques suivantes: Attention! Le non respect de ces instructions peut entraîner des accidents impliquant des blessures graves. Ne pas suivre ces instructions peut entraîner l´endommagement ou destruction du produit. Consignes de sécurité Géneral Le non respect de ces instructions peut entraîner des accidents impliquant des blessures graves.
Avant l´installation, ré-installation ou le dépannage: • Arrêtez TD4 • Retirez la prise du secteur • Soulagez TD4 des toutes charges qui pourraient être émises lors de l´utilisation Avant de démarage: • Assurez-vous que le système a été installalé comme indiqué dans le mannuel d´utilisateur. • Assurez-vous que la tension du boîtier de contrôle est correcte avant que le système soit connecté sur le secteur. • Système de connection.
Seulement pour les marchés au sein de l´UE: Cet appareil peut-être utilisé par des enfants âgés de 8 ans et plus, ainsi que les personnes dont les capacités physiques, sensorielles ou mentales sont réduites ou ayant un manque d´expérience et de connaissance si elles ont bénéficié d´une surveillance ou d´instructions concernant l´utilisation de l´appareil en toute sécurité et compris les risques encourus. Les enfants ne doivent pas jouer avec l´appareil.
Repairs In order to avoid the risk of malfunction, all TWINDRIVE® repairs must only be carried out by authorised LINAK workshops or repairers, as special tools must be used and special gaskets must be fitted. TWINDRIVE under warranty must also be returned to authorised LINAK workshops.
Misc. on the TWINDRIVE® TD4 system This system is a TWINDRIVE system developed for leisure beds and for indoor use in private homes. Warranty There is 36 months’ warranty on the TWINDRIVE® products against manufacturing faults calculated from the production date of the individual products (see label). LINAK A/S’ warranty is only valid in so far as the equipment has been used and maintained correctly and has not been tampered with. Furthermore, the system must not be exposed to violent treatment.
Mounting instructions for the TWINDRIVE® system: Mounting is made by pushing the TD4 unit into the bed bracket and thereafter slide the closing devices on. It is IMPORTANT to be completely sure that the closing devices are in place before using the TD4. Do not drive the TD4 system without the closing devices mounted The bed brackets must have a smooth surface without burs and welding blops in the area where the TD4 is mounted.
TD4 Standard - Start-up (How to pair Bluetooth connection) It is possible to pair multiple devices to the TD4 via Bluetooth® Smart. See following instructions: 1. Pairing your control Connect the TD4 to the mains via the mains cable. Now the TD4 will be in pairing mode in 3 minutes and the Under Bed Light will blink to indicate this. Take you hand control and press the Back “Up” and “Down” buttons at the same time. Now the light will give a long blink and indicate that the control and the TD4 are paired up.
2. Pairing your smartphone or tablet Connect the TD4 to the mains via the mains cable. Now the TD4 will be in pairing mode in 3 minutes and the Under Bed Light will blink to indicate this. Enable Bluetooth® on your smartphone/tablet. Open the TD4 app and a “search bed” page will be displayed. A list of previously connected Twindrives and Twindrives in pairing mode will appear. Find the TD4 you wish to connect on the list and tap to connect.
3. Pairing another device later If you wish to connect another control or a smartphone/tablet to the TD4 later, just disconnect, wait 2 seconds and connect the TD4 to the mains to get it in pairing mode again. See instructions 1 or 2 above to find out how to pair the device, you want. 1 2 The TD4 will be in pairing mode every time the system has been out of power and connects again. To get the system out of pairing mode – simply press any button on an already paired device.
Mechanical emergency lowering Emergency lowering is meant for lowering the bed if a power failure occurs and the bed needs to be driven down into horizontal position. Disconnect the TD4 from the mains. Take the hex key on the side of the TD4. Underneath the TD4 are two gaps for mechanical lowering – simply place the hex key in the gap, one end at a time, and turn the hex key in the direction the arrow indicates. 1 2 3 It is important to turn the key in the direction indicated on the housing.
Cable strain relief It is important to use the cable relief on the TD4. By using the relief you avoid that the mains cable plug is pulled out of the TD4 resulting in a malfunction. Depending on the thickness of the cable, you can choose to lead the cable through all 3 or just around the middle relief.
TD4 Advanced - Start-up (How to pair Bluetooth connection) It is possible to pair multiple devices to the TD4 via Bluetooth® Smart. See following instructions: 1. Pairing your control Connect the TD4 to the mains via the connection cable. Now the TD4 will be in pairing mode in 3 minutes and the Under Bed Light will blink to indicate this. Take you hand control and press the Back “Up” and “Down” buttons at the same time.
2. Pairing your smartphone or tablet Connect the TD4 to the mains via the connection cable. Now the TD4 will be in pairing mode in 3 minutes and the Under Bed Light will blink to indicate this. Enable Bluetooth® on your smartphone/tablet. Open the TD4 app and a “search bed” page will be displayed. A list of previously connected Twindrives and Twindrives in pairing mode will appear. Find the TD4 you wish to connect on the list and tap to connect.
3. Pairing another device later If you wish to connect another control or a smartphone/tablet to the TD4 later, just disconnect, wait 2 minutes and connect the TD4 to the mains to get it in pairing mode again. See instructions 1 or 2 above to find out how to pair the device, you want. 1 2 The TD4 will be in pairing mode every time the system has been out of power and connects again. To get the system out of pairing mode – simply press any button on an already paired device.
Mechanical emergency lowering Emergency lowering is meant for lowering the bed if a power failure occurs and the bed needs to be driven down into horizontal position. Disconnect the TD4 from the mains. Take the hex key on the side of the TD4. Underneath the TD4 are two gaps for mechanical lowering – simply place the hex key in the gap, one end at a time, and turn the hex key in the direction the arrow indicates. 1 2 3 It is important to turn the key in the direction indicated on the housing.
Electrical emergency lowering Connection of emergency lowering: 1. Remove the SMPS from the mains. 2. Notice! If a locking device is mounted on the SMPS remove it now. 3. Unplug the connection cable from the SMPS 4. Connect the connection cable to the battery box for emergency lowering. 1 2 3 4 Cable strain relief It is important to use the cable relief on the TD4. By using the relief you avoid that the connection cable plug is pulled out of the TD4 resulting in a malfunction.
Functional description Hand Control HB10BL: Up – down back motor Up – down leg motor Common operation up/down (option) Hand Control HC05BL: Up – down back motor Up – down leg motor Common operation up/down (option) Light Button Hand Control HC10BL: Up – down back motor Up – down leg motor Common operation up/down (option) Light Button Hand Control HC20BL: Up – down back motor Up – down leg motor up to 3 extra channels Common operation up/down (option) Memory positions (3 positions) Store Button Light
Label for TD4 Advanced Label for TD4 Standard Label for HB10 Label for HC05 Label for HC10 Label for HC20 Page 27 of 28
Disposal of LINAK products As LINAK customers often ask us how our products can be disposed of or scrapped we have prepared this guidance that enables a classification to different waste fractions for recycling or combustion. Guidance We recommend to disassemble our product into as many fractions as possible at the disposal and try to make it recycable. As examples of main groups within waste fractions we can mention: Metal, plastic, cable shoe, combustible waste and collection for recovery.
Main groups of disposal Product main groups TD4 Scrap Cable scrap Electronics scrap X X X X X X X X HB10BL HC05 Plastic recycling or combustin HC10BL X X X HC20BL X X X Comments Disposal of batteries Details regarding safe disposal of used and leaking batteries: Batteries should be disposed in accordance with appropriate federal, state and local regulations. LINAK recommends that used or leaking batteries are disposed through the local recycling system.
DRAWING APPENDIX g No.: TD4_ADVANCED TWINDRIVE® TD4 System Advanced 76 105 19 25.
o.: TD4_STANDARD TWINDRIVE® TD4 System Standard 76 105 19 25.
HB10BL Hand Control Drawing No.: HC05 HC05BL Hand Control 13.5 100 2.9 34 1.
LINAK APPLICATION POLICY The purpose of the application policy is to define areas of responsibilities in relation to applying a LINAK product defined as hardware, software, technical advice, etc. related to an existing or a new customer application. LINAK products as defined above are applicable for a wide range of applications within the Medical, Furniture, Desk, and Industry areas.
FACTORIES CHINA LINAK (Shenzhen) Actuator Systems, Ltd. Phone: +86 755 8610 6656 Fax: +86 755 8610 6990 E-mail: sales@linak.cn www.linak.cn DENMARK SLOVAKIA LINAK A/S - Group Headquarters, Guderup Phone: +45 73 15 15 15 Fax: +45 74 45 80 48 Fax: +45 73 15 16 13 (Sales) E-mail: info@linak.com www.linak.com LINAK Slovakia s.r.o. Phone: +421 51 75 63 414 Fax: +421 51 75 63 410 E-mail: jp@linak.sk www.linak.com USA LINAK U.S. Inc.
